X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=30d44b78171a53e5dcc9e3b42d67266f61975a75;hb=c010b2f76c3032e48097a6eef291d8593d5d79a6;hp=312fe77764a48cba9fb04e000fc2dffeba7fa978;hpb=84c3d4aaec3338201b449034beac41635866bddf;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 312fe77764a..30d44b78171 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -147,10 +147,14 @@ and is between 256 and 4096 characters. It is defined in the file
 			default: 0
 
 	acpi_sleep=	[HW,ACPI] Sleep options
-			Format: { s3_bios, s3_mode, s3_beep }
+			Format: { s3_bios, s3_mode, s3_beep, old_ordering }
 			See Documentation/power/video.txt for s3_bios and s3_mode.
 			s3_beep is for debugging; it makes the PC's speaker beep
 			as soon as the kernel's real-mode entry point is called.
+			old_ordering causes the ACPI 1.0 ordering of the _PTS
+			control method, wrt putting devices into low power
+			states, to be enforced (the ACPI 2.0 ordering of _PTS is
+			used by default).
 
 	acpi_sci=	[HW,ACPI] ACPI System Control Interrupt trigger mode
 			Format: { level | edge | high | low }
@@ -818,7 +822,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			See Documentation/ide/ide.txt.
 
 	idle=		[X86]
-			Format: idle=poll or idle=mwait
+			Format: idle=poll or idle=mwait, idle=halt, idle=nomwait
 			Poll forces a polling idle loop that can slightly improves the performance
 			of waking up a idle CPU, but will use a lot of power and make the system
 			run hot. Not recommended.
@@ -826,6 +830,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			to not use it because it doesn't save as much power as a normal idle
 			loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
 			as idle=poll.
+			idle=halt. Halt is forced to be used for CPU idle.
+			In such case C2/C3 won't be used again.
+			idle=nomwait. Disable mwait for CPU C-states
 
 	ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
 			Claim all unknown PCI IDE storage controllers.
@@ -1199,7 +1206,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			         or
 			         memmap=0x10000$0x18690000
 
-	memtest=	[KNL,X86_64] Enable memtest
+	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
 			range: 0,4 : pattern number
 			default : 0 <disable>
@@ -1272,6 +1279,13 @@ and is between 256 and 4096 characters. It is defined in the file
 			This usage is only documented in each driver source
 			file if at all.
 
+	nf_conntrack.acct=
+			[NETFILTER] Enable connection tracking flow accounting
+			0 to disable accounting
+			1 to enable accounting
+			Default value depends on CONFIG_NF_CT_ACCT that is
+			going to be removed in 2.6.29.
+
 	nfsaddrs=	[NFS]
 			See Documentation/filesystems/nfsroot.txt.
 
@@ -1534,6 +1548,9 @@ and is between 256 and 4096 characters. It is defined in the file
 				Use with caution as certain devices share
 				address decoders between ROMs and other
 				resources.
+		norom		[X86-32,X86_64] Do not assign address space to
+				expansion ROMs that do not already have
+				BIOS assigned address ranges.
 		irqmask=0xMMMM	[X86-32] Set a bit mask of IRQs allowed to be
 				assigned automatically to PCI devices. You can
 				make the kernel exclude IRQs of your ISA cards
@@ -2148,6 +2165,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			Note that genuine overcurrent events won't be
 			reported either.
 
+	unknown_nmi_panic
+			[X86-32,X86-64]
+			Set unknown_nmi_panic=1 early on boot.
+
 	usbcore.autosuspend=
 			[USB] The autosuspend time delay (in seconds) used
 			for newly-detected USB devices (default 2).  This