X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=aeedb89a307ae2d8b1f6c9aa58399146e6c332b2;hb=4ce707fbb6ee23d95a71679180cf9c273bee8943;hp=954b23cecfd19bc98f996c26ecfbd7bf8f0f44e9;hpb=21cdbc1378e8aa96e1ed4a606dce1a8e7daf7fdf;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 954b23cecfd..aeedb89a307 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -492,11 +492,23 @@ and is between 256 and 4096 characters. It is defined in the file
 			Range: 0 - 8192
 			Default: 64
 
+	dma_debug=off	If the kernel is compiled with DMA_API_DEBUG support
+			this option disables the debugging code at boot.
+
+	dma_debug_entries=<number>
+			This option allows to tune the number of preallocated
+			entries for DMA-API debugging code. One entry is
+			required per DMA-API allocation. Use this if the
+			DMA-API debugging code disables itself because the
+			architectural default is too low.
+
 	hpet=		[X86-32,HPET] option to control HPET usage
-			Format: { enable (default) | disable | force }
+			Format: { enable (default) | disable | force |
+				verbose }
 			disable: disable HPET and use PIT instead
 			force: allow force enabled of undocumented chips (ICH4,
 			VIA, nVidia)
+			verbose: show contents of HPET registers during setup
 
 	com20020=	[HW,NET] ARCnet - COM20020 chipset
 			Format:
@@ -834,6 +846,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			       If specified, z/VM IUCV HVC accepts connections
 			       from listed z/VM user IDs only.
 
+	i2c_bus=	[HW] Override the default board specific I2C bus speed
+			     or register an additional I2C bus that is not
+			     registered from board initialization code.
+			     Format:
+			     <bus_id>,<clkrate>
+
 	i8042.debug	[HW] Toggle i8042 debug mode
 	i8042.direct	[HW] Put keyboard port into non-translated mode
 	i8042.dumbkbd	[HW] Pretend that controller can only read data from
@@ -1323,8 +1341,13 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
-			range: 0,4 : pattern number
 			default : 0 <disable>
+			Specifies the number of memtest passes to be
+			performed. Each pass selects another test
+			pattern from a given set of patterns. Memtest
+			fills the memory with this pattern, validates
+			memory contents and reserves bad memory
+			regions that are detected.
 
 	meye.*=		[HW] Set MotionEye Camera parameters
 			See Documentation/video4linux/meye.txt.
@@ -2017,15 +2040,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			If enabled at boot time, /selinux/disable can be used
 			later to disable prior to initial policy load.
 
-	selinux_compat_net =
-			[SELINUX] Set initial selinux_compat_net flag value.
-                        Format: { "0" | "1" }
-                        0 -- use new secmark-based packet controls
-                        1 -- use legacy packet controls
-                        Default value is 0 (preferred).
-                        Value can be changed at runtime via
-                        /selinux/compat_net.
-
 	serialnumber	[BUGS=X86-32]
 
 	shapers=	[NET]