X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=dd28a0d56981e4e0376fb5010086c817633a6a3b;hb=e5403bff8a4018240f012fd4c7afa24c2e75b469;hp=d0fff6302f68de3b0ec08afd9df111a5974701fe;hpb=4dd9ec4946b4651a295d3bc8df9c15ac692a8f4e;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index d0fff6302f6..dd28a0d5698 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -284,6 +284,11 @@ and is between 256 and 4096 characters. It is defined in the file
 			isolate - enable device isolation (each device, as far
 			          as possible, will get its own protection
 			          domain)
+			fullflush - enable flushing of IO/TLB entries when
+				    they are unmapped. Otherwise they are
+				    flushed before they will be reused, which
+				    is a lot of faster
+
 	amd_iommu_size= [HW,X86-64]
 			Define the size of the aperture for the AMD IOMMU
 			driver. Possible values are:
@@ -653,11 +658,12 @@ and is between 256 and 4096 characters. It is defined in the file
 	earlyprintk=	[X86-32,X86-64,SH,BLACKFIN]
 			earlyprintk=vga
 			earlyprintk=serial[,ttySn[,baudrate]]
+			earlyprintk=dbgp
 
 			Append ",keep" to not disable it when the real console
 			takes over.
 
-			Only vga or serial at a time, not both.
+			Only vga or serial or usb debug port at a time.
 
 			Currently only ttyS0 and ttyS1 are supported.
 
@@ -790,6 +796,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			Defaults to the default architecture's huge page size
 			if not specified.
 
+	i8042.debug	[HW] Toggle i8042 debug mode
 	i8042.direct	[HW] Put keyboard port into non-translated mode
 	i8042.dumbkbd	[HW] Pretend that controller can only read data from
 			     keyboard and cannot control its state
@@ -1226,6 +1233,29 @@ and is between 256 and 4096 characters. It is defined in the file
 			         or
 			         memmap=0x10000$0x18690000
 
+	memory_corruption_check=0/1 [X86]
+			Some BIOSes seem to corrupt the first 64k of
+			memory when doing things like suspend/resume.
+			Setting this option will scan the memory
+			looking for corruption.  Enabling this will
+			both detect corruption and prevent the kernel
+			from using the memory being corrupted.
+			However, its intended as a diagnostic tool; if
+			repeatable BIOS-originated corruption always
+			affects the same memory, you can use memmap=
+			to prevent the kernel from using that memory.
+
+	memory_corruption_check_size=size [X86]
+			By default it checks for corruption in the low
+			64k, making this memory unavailable for normal
+			use.  Use this parameter to scan for
+			corruption in more or less memory.
+
+	memory_corruption_check_period=seconds [X86]
+			By default it checks for corruption every 60
+			seconds.  Use this parameter to check at some
+			other rate.  0 disables periodic checking.
+
 	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
 			range: 0,4 : pattern number
@@ -1423,6 +1453,12 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	nolapic_timer	[X86-32,APIC] Do not use the local APIC timer.
 
+	nox2apic	[X86-64,APIC] Do not enable x2APIC mode.
+
+	x2apic_phys	[X86-64,APIC] Use x2apic physical mode instead of
+			default x2apic cluster mode on platforms
+			supporting x2apic.
+
 	noltlbs		[PPC] Do not use large page/tlb entries for kernel
 			lowmem mapping on PPC40x.
 
@@ -1678,6 +1714,11 @@ and is between 256 and 4096 characters. It is defined in the file
 			autoconfiguration.
 			Ranges are in pairs (memory base and size).
 
+	dynamic_printk
+			Enables pr_debug()/dev_dbg() calls if
+			CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
+			be switched on/off via <debugfs>/dynamic_printk/modules
+
 	print-fatal-signals=
 			[KNL] debug: print fatal signals
 			print-fatal-signals=1: print segfault info to