X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fmd.txt;h=1da9d1b1793f3436b3561a48de7fbcd8c893e74e;hb=1c13a243a461dd5b089d29e5d57f260c990e462c;hp=396cdd982c26505ee39a577a64a7fb2c7472985e;hpb=0a3abcf75bf391fec4e32356ab5ddb8f5d2e6b41;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/md.txt b/Documentation/md.txt
index 396cdd982c2..1da9d1b1793 100644
--- a/Documentation/md.txt
+++ b/Documentation/md.txt
@@ -236,6 +236,11 @@ All md devices contain:
      writing the word for the desired state, however some states
      cannot be explicitly set, and some transitions are not allowed.
 
+     Select/poll works on this file.  All changes except between
+     	active_idle and active (which can be frequent and are not
+	very interesting) are notified.  active->active_idle is
+	reported if the metadata is externally managed.
+
      clear
          No devices, no size, no level
          Writing is equivalent to STOP_ARRAY ioctl
@@ -292,6 +297,10 @@ Each directory contains:
 	      writemostly - device will only be subject to read
 		         requests if there are no other options.
 			 This applies only to raid1 arrays.
+	      blocked  - device has failed, metadata is "external",
+	                 and the failure hasn't been acknowledged yet.
+			 Writes that would write to this device if
+			 it were not faulty are blocked.
 	      spare    - device is working, but not a full member.
 			 This includes spares that are in the process
 			 of being recovered to
@@ -301,6 +310,12 @@ Each directory contains:
 	Writing "remove" removes the device from the array.
 	Writing "writemostly" sets the writemostly flag.
 	Writing "-writemostly" clears the writemostly flag.
+	Writing "blocked" sets the "blocked" flag.
+	Writing "-blocked" clear the "blocked" flag and allows writes
+		to complete.
+
+	This file responds to select/poll. Any change to 'faulty'
+	or 'blocked' causes an event.
 
       errors
 	An approximate count of read errors that have been detected on
@@ -332,7 +347,7 @@ Each directory contains:
         for storage of data.  This will normally be the same as the
 	component_size.  This can be written while assembling an
         array.  If a value less than the current component_size is
-        written, component_size will be reduced to this value.
+        written, it will be rejected.
 
 
 An active md device will also contain and entry for each active device
@@ -381,6 +396,19 @@ also have
 	'check' and 'repair' will start the appropriate process
            providing the current state is 'idle'.
 
+      This file responds to select/poll.  Any important change in the value
+      triggers a poll event.  Sometimes the value will briefly be
+      "recover" if a recovery seems to be needed, but cannot be
+      achieved. In that case, the transition to "recover" isn't
+      notified, but the transition away is.
+
+   degraded
+      This contains a count of the number of devices by which the
+      arrays is degraded.  So an optimal array with show '0'.  A
+      single failed/missing drive will show '1', etc.
+      This file responds to select/poll, any increase or decrease
+      in the count of missing devices will trigger an event.
+
    mismatch_count
       When performing 'check' and 'repair', and possibly when
       performing 'resync', md will count the number of errors that are
@@ -450,3 +478,9 @@ These currently include
       there are upper and lower limits (32768, 16).  Default is 128.
   strip_cache_active (currently raid5 only)
       number of active entries in the stripe cache
+  preread_bypass_threshold (currently raid5 only)
+      number of times a stripe requiring preread will be bypassed by
+      a stripe that does not require preread.  For fairness defaults
+      to 1.  Setting this to 0 disables bypass accounting and
+      requires preread stripes to wait until all full-width stripe-
+      writes are complete.  Valid values are 0 to stripe_cache_size.