X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=arch%2Farm%2Fmach-at91%2Fboard-sam9-l9260.c;h=b4834697753499278b85aea36c710d990dd9ce49;hb=14a3c4ab0e58d143c7928c9eb2f2610205e13bf2;hp=99bb4cc23a0950af07d18712b077696c2f6842c9;hpb=a45fbc33137b11e479ea8b7d478a1d7e6488971b;p=linux-2.6-omap-h63xx.git

diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index 99bb4cc23a0..b4834697753 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -38,7 +38,9 @@
 
 #include <mach/board.h>
 #include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
 
+#include "sam9_smc.h"
 #include "generic.h"
 
 
@@ -148,13 +150,34 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
 };
 
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
 
 /*
  * MCI (SD/MMC)
@@ -178,7 +201,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* NAND */
-	at91_add_device_nand(&ek_nand_data);
+	ek_add_device_nand();
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */