X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=arch%2Fx86%2FKconfig;h=44d4f2130d014be68f3a0171d2e4e980b78443ad;hb=d84705969f898f294bc3fc32eca33580f14105bd;hp=ac2fb0641a041e4a28055867140f458613673dc2;hpb=45edb89ffd6386f95a7a9e1e5461b0e61c76aa14;p=linux-2.6-omap-h63xx.git diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index ac2fb0641a0..44d4f2130d0 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -29,6 +29,7 @@ config X86 select HAVE_FTRACE select HAVE_KVM if ((X86_32 && !X86_VOYAGER && !X86_VISWS && !X86_NUMAQ) || X86_64) select HAVE_ARCH_KGDB if !X86_VOYAGER + select HAVE_ARCH_TRACEHOOK select HAVE_GENERIC_DMA_COHERENT if X86_32 select HAVE_EFFICIENT_UNALIGNED_ACCESS @@ -553,6 +554,7 @@ config CALGARY_IOMMU_ENABLED_BY_DEFAULT config AMD_IOMMU bool "AMD IOMMU support" select SWIOTLB + select PCI_MSI depends on X86_64 && PCI && ACPI help With this option you can enable support for AMD IOMMU hardware in @@ -577,35 +579,29 @@ config SWIOTLB config IOMMU_HELPER def_bool (CALGARY_IOMMU || GART_IOMMU || SWIOTLB || AMD_IOMMU) + config MAXSMP bool "Configure Maximum number of SMP Processors and NUMA Nodes" - depends on X86_64 && SMP + depends on X86_64 && SMP && BROKEN default n help Configure maximum number of CPUS and NUMA Nodes for this architecture. If unsure, say N. -if MAXSMP -config NR_CPUS - int - default "4096" -endif - -if !MAXSMP config NR_CPUS - int "Maximum number of CPUs (2-4096)" - range 2 4096 + int "Maximum number of CPUs (2-512)" if !MAXSMP + range 2 512 depends on SMP + default "4096" if MAXSMP default "32" if X86_NUMAQ || X86_SUMMIT || X86_BIGSMP || X86_ES7000 default "8" help This allows you to specify the maximum number of CPUs which this - kernel will support. The maximum supported value is 4096 and the + kernel will support. The maximum supported value is 512 and the minimum value which makes sense is 2. This is purely to save memory - each supported CPU adds approximately eight kilobytes to the kernel image. -endif config SCHED_SMT bool "SMT (Hyperthreading) scheduler support" @@ -951,9 +947,9 @@ config NUMA local memory controller of the CPU and add some more NUMA awareness to the kernel. - For i386 this is currently highly experimental and should be only + For 32-bit this is currently highly experimental and should be only used for kernel development. It might also cause boot failures. - For x86_64 this is recommended on all multiprocessor Opteron systems. + For 64-bit this is recommended on all multiprocessor Opteron systems. If the system is EM64T, you should say N unless your system is EM64T NUMA. @@ -996,17 +992,10 @@ config NUMA_EMU into virtual nodes when booted with "numa=fake=N", where N is the number of nodes. This is only useful for debugging. -if MAXSMP - config NODES_SHIFT - int - default "9" -endif - -if !MAXSMP -config NODES_SHIFT - int "Maximum NUMA Nodes (as a power of 2)" + int "Maximum NUMA Nodes (as a power of 2)" if !MAXSMP range 1 9 if X86_64 + default "9" if MAXSMP default "6" if X86_64 default "4" if X86_NUMAQ default "3" @@ -1014,7 +1003,6 @@ config NODES_SHIFT help Specify the maximum number of NUMA Nodes available on the target system. Increases memory reserved to accomodate various tables. -endif config HAVE_ARCH_BOOTMEM_NODE def_bool y @@ -1034,7 +1022,7 @@ config HAVE_ARCH_ALLOC_REMAP config ARCH_FLATMEM_ENABLE def_bool y - depends on X86_32 && ARCH_SELECT_MEMORY_MODEL && X86_PC && !NUMA + depends on X86_32 && ARCH_SELECT_MEMORY_MODEL && !NUMA config ARCH_DISCONTIGMEM_ENABLE def_bool y @@ -1050,7 +1038,7 @@ config ARCH_SPARSEMEM_DEFAULT config ARCH_SPARSEMEM_ENABLE def_bool y - depends on X86_64 || NUMA || (EXPERIMENTAL && X86_PC) + depends on X86_64 || NUMA || (EXPERIMENTAL && X86_PC) || X86_GENERICARCH select SPARSEMEM_STATIC if X86_32 select SPARSEMEM_VMEMMAP_ENABLE if X86_64 @@ -1131,10 +1119,10 @@ config MTRR You can safely say Y even if your machine doesn't have MTRRs, you'll just add about 9 KB to your kernel. - See for more information. + See for more information. config MTRR_SANITIZER - bool + def_bool y prompt "MTRR cleanup support" depends on MTRR help @@ -1145,7 +1133,7 @@ config MTRR_SANITIZER The largest mtrr entry size for a continous block can be set with mtrr_chunk_size. - If unsure, say N. + If unsure, say Y. config MTRR_SANITIZER_ENABLE_DEFAULT int "MTRR cleanup enable value (0-1)" @@ -1205,7 +1193,6 @@ config IRQBALANCE config SECCOMP def_bool y prompt "Enable seccomp to safely compute untrusted bytecode" - depends on PROC_FS help This kernel feature is useful for number crunching applications that may need to compute untrusted bytecode during their @@ -1213,7 +1200,7 @@ config SECCOMP the process as file descriptors supporting the read/write syscalls, it's possible to isolate those applications in their own address space using seccomp. Once seccomp is - enabled via /proc//seccomp, it cannot be disabled + enabled via prctl(PR_SET_SECCOMP), it cannot be disabled and the task is only allowed to execute a few safe syscalls defined by each seccomp mode. @@ -1263,7 +1250,7 @@ config KEXEC strongly in flux, so no good recommendation can be made. config CRASH_DUMP - bool "kernel crash dumps (EXPERIMENTAL)" + bool "kernel crash dumps" depends on X86_64 || (X86_32 && HIGHMEM) help Generate crash dump after being started by kexec. @@ -1370,14 +1357,14 @@ config PHYSICAL_ALIGN Don't change this unless you know what you are doing. config HOTPLUG_CPU - bool "Support for suspend on SMP and hot-pluggable CPUs (EXPERIMENTAL)" - depends on SMP && HOTPLUG && EXPERIMENTAL && !X86_VOYAGER + bool "Support for hot-pluggable CPUs" + depends on SMP && HOTPLUG && !X86_VOYAGER ---help--- - Say Y here to experiment with turning CPUs off and on, and to - enable suspend on SMP systems. CPUs can be controlled through - /sys/devices/system/cpu. - Say N if you want to disable CPU hotplug and don't need to - suspend. + Say Y here to allow turning CPUs off and on. CPUs can be + controlled through /sys/devices/system/cpu. + ( Note: power management support will enable this option + automatically on SMP systems. ) + Say N if you want to disable CPU hotplug. config COMPAT_VDSO def_bool y @@ -1392,6 +1379,51 @@ config COMPAT_VDSO If unsure, say Y. +config CMDLINE_BOOL + bool "Built-in kernel command line" + default n + help + Allow for specifying boot arguments to the kernel at + build time. On some systems (e.g. embedded ones), it is + necessary or convenient to provide some or all of the + kernel boot arguments with the kernel itself (that is, + to not rely on the boot loader to provide them.) + + To compile command line arguments into the kernel, + set this option to 'Y', then fill in the + the boot arguments in CONFIG_CMDLINE. + + Systems with fully functional boot loaders (i.e. non-embedded) + should leave this option set to 'N'. + +config CMDLINE + string "Built-in kernel command string" + depends on CMDLINE_BOOL + default "" + help + Enter arguments here that should be compiled into the kernel + image and used at boot time. If the boot loader provides a + command line at boot time, it is appended to this string to + form the full kernel command line, when the system boots. + + However, you can use the CONFIG_CMDLINE_OVERRIDE option to + change this behavior. + + In most cases, the command line (whether built-in or provided + by the boot loader) should specify the device for the root + file system. + +config CMDLINE_OVERRIDE + bool "Built-in command line overrides boot loader arguments" + default n + depends on CMDLINE_BOOL + help + Set this option to 'Y' to have the kernel ignore the boot loader + command line, and use ONLY the built-in command line. + + This is used to work around broken boot loaders. This should + be set to 'N' under normal conditions. + endmenu config ARCH_ENABLE_MEMORY_HOTPLUG @@ -1657,6 +1689,14 @@ config DMAR_FLOPPY_WA workaround will setup a 1:1 mapping for the first 16M to make floppy (an ISA device) work. +config INTR_REMAP + bool "Support for Interrupt Remapping (EXPERIMENTAL)" + depends on X86_64 && X86_IO_APIC && PCI_MSI && ACPI && EXPERIMENTAL + help + Supports Interrupt remapping for IO-APIC and MSI devices. + To use x2apic mode in the CPU's which support x2APIC enhancements or + to support platforms with CPU's having > 8 bit APIC ID, say Y. + source "drivers/pci/pcie/Kconfig" source "drivers/pci/Kconfig" @@ -1787,7 +1827,7 @@ config COMPAT_FOR_U64_ALIGNMENT config SYSVIPC_COMPAT def_bool y - depends on X86_64 && COMPAT && SYSVIPC + depends on COMPAT && SYSVIPC endmenu