X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=arch%2Fx86%2FKconfig;h=7820d447bb8d31f71c40b1347ca94d8cf2a9649f;hb=c885df50f571faf9fd9f395361cfff1b3a16e06e;hp=68d91c8233f42162039af96c8ed1fdd3e1d6a88e;hpb=1bbe44f69d7ea20740aaf5aba356e331a74b58b3;p=linux-2.6-omap-h63xx.git

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 68d91c8233f..7820d447bb8 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -577,35 +577,29 @@ config SWIOTLB
 
 config IOMMU_HELPER
 	def_bool (CALGARY_IOMMU || GART_IOMMU || SWIOTLB || AMD_IOMMU)
+
 config MAXSMP
 	bool "Configure Maximum number of SMP Processors and NUMA Nodes"
-	depends on X86_64 && SMP
+	depends on X86_64 && SMP && BROKEN
 	default n
 	help
 	  Configure maximum number of CPUS and NUMA Nodes for this architecture.
 	  If unsure, say N.
 
-if MAXSMP
 config NR_CPUS
-	int
-	default "4096"
-endif
-
-if !MAXSMP
-config NR_CPUS
-	int "Maximum number of CPUs (2-4096)"
-	range 2 4096
+	int "Maximum number of CPUs (2-512)" if !MAXSMP
+	range 2 512
 	depends on SMP
+	default "4096" if MAXSMP
 	default "32" if X86_NUMAQ || X86_SUMMIT || X86_BIGSMP || X86_ES7000
 	default "8"
 	help
 	  This allows you to specify the maximum number of CPUs which this
-	  kernel will support.  The maximum supported value is 4096 and the
+	  kernel will support.  The maximum supported value is 512 and the
 	  minimum value which makes sense is 2.
 
 	  This is purely to save memory - each supported CPU adds
 	  approximately eight kilobytes to the kernel image.
-endif
 
 config SCHED_SMT
 	bool "SMT (Hyperthreading) scheduler support"
@@ -996,17 +990,10 @@ config NUMA_EMU
 	  into virtual nodes when booted with "numa=fake=N", where N is the
 	  number of nodes. This is only useful for debugging.
 
-if MAXSMP
-
 config NODES_SHIFT
-	int
-	default "9"
-endif
-
-if !MAXSMP
-config NODES_SHIFT
-	int "Maximum NUMA Nodes (as a power of 2)"
+	int "Maximum NUMA Nodes (as a power of 2)" if !MAXSMP
 	range 1 9   if X86_64
+	default "9" if MAXSMP
 	default "6" if X86_64
 	default "4" if X86_NUMAQ
 	default "3"
@@ -1014,7 +1001,6 @@ config NODES_SHIFT
 	help
 	  Specify the maximum number of NUMA Nodes available on the target
 	  system.  Increases memory reserved to accomodate various tables.
-endif
 
 config HAVE_ARCH_BOOTMEM_NODE
 	def_bool y
@@ -1073,6 +1059,36 @@ config HIGHPTE
 	  low memory.  Setting this option will put user-space page table
 	  entries in high memory.
 
+config X86_CHECK_BIOS_CORRUPTION
+        bool "Check for low memory corruption"
+	help
+	 Periodically check for memory corruption in low memory, which
+	 is suspected to be caused by BIOS.  Even when enabled in the
+	 configuration, it is disabled at runtime.  Enable it by
+	 setting "memory_corruption_check=1" on the kernel command
+	 line.  By default it scans the low 64k of memory every 60
+	 seconds; see the memory_corruption_check_size and
+	 memory_corruption_check_period parameters in
+	 Documentation/kernel-parameters.txt to adjust this.
+
+	 When enabled with the default parameters, this option has
+	 almost no overhead, as it reserves a relatively small amount
+	 of memory and scans it infrequently.  It both detects corruption
+	 and prevents it from affecting the running system.
+
+	 It is, however, intended as a diagnostic tool; if repeatable
+	 BIOS-originated corruption always affects the same memory,
+	 you can use memmap= to prevent the kernel from using that
+	 memory.
+
+config X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK
+        bool "Set the default setting of memory_corruption_check"
+	depends on X86_CHECK_BIOS_CORRUPTION
+	default y
+	help
+	 Set whether the default state of memory_corruption_check is
+	 on or off.
+
 config MATH_EMULATION
 	bool
 	prompt "Math emulation" if X86_32