X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fata%2Fpata_amd.c;h=0ec9c7d9fe9d607250a07bc47a6ce4d3c087041a;hb=ab77163008c596aad9624ceab190d840c0143fa8;hp=26665c396485898b6785140ba38e8f913760439a;hpb=eddeb0e2d863e3941d8768e70cb50c6120e61fa0;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 26665c39648..0ec9c7d9fe9 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -1,7 +1,6 @@
 /*
  * pata_amd.c 	- AMD PATA for new ATA layer
  *			  (C) 2005-2006 Red Hat Inc
- *			  Alan Cox <alan@redhat.com>
  *
  *  Based on pata-sil680. Errata information is taken from data sheets
  *  and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are
@@ -84,32 +83,32 @@ static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offse
 
 	/* Configure the address set up timing */
 	pci_read_config_byte(pdev, offset + 0x0C, &t);
-	t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
+	t = (t & ~(3 << ((3 - dn) << 1))) | ((clamp_val(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
 	pci_write_config_byte(pdev, offset + 0x0C , t);
 
 	/* Configure the 8bit I/O timing */
 	pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)),
-		((FIT(at.act8b, 1, 16) - 1) << 4) | (FIT(at.rec8b, 1, 16) - 1));
+		((clamp_val(at.act8b, 1, 16) - 1) << 4) | (clamp_val(at.rec8b, 1, 16) - 1));
 
 	/* Drive timing */
 	pci_write_config_byte(pdev, offset + 0x08 + (3 - dn),
-		((FIT(at.active, 1, 16) - 1) << 4) | (FIT(at.recover, 1, 16) - 1));
+		((clamp_val(at.active, 1, 16) - 1) << 4) | (clamp_val(at.recover, 1, 16) - 1));
 
 	switch (clock) {
 		case 1:
-		t = at.udma ? (0xc0 | (FIT(at.udma, 2, 5) - 2)) : 0x03;
+		t = at.udma ? (0xc0 | (clamp_val(at.udma, 2, 5) - 2)) : 0x03;
 		break;
 
 		case 2:
-		t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 2, 10)]) : 0x03;
+		t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 2, 10)]) : 0x03;
 		break;
 
 		case 3:
-		t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 10)]) : 0x03;
+		t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 10)]) : 0x03;
 		break;
 
 		case 4:
-		t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 15)]) : 0x03;
+		t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 15)]) : 0x03;
 		break;
 
 		default: