X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fata%2Fpata_opti.c;h=e4fa4d565e96331dfed1fa0bedfcb44a36248fe3;hb=9144f3821d2cba9f16cdf3ff1b881384f4b68b53;hp=8f79447b6151a006629ce1b0aea6a94d7f030b4d;hpb=c4ec20717313daafba59225f812db89595952b83;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index 8f79447b615..e4fa4d565e9 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -1,7 +1,6 @@
 /*
  * pata_opti.c 	- ATI PATA for new ATA layer
  *			  (C) 2005 Red Hat Inc
- *			  Alan Cox <alan@redhat.com>
  *
  * Based on
  *  linux/drivers/ide/pci/opti621.c		Version 0.7	Sept 10, 2002
@@ -64,22 +63,7 @@ static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
 	if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
 		return -ENOENT;
 
-	return ata_std_prereset(link, deadline);
-}
-
-/**
- *	opti_probe_reset		-	probe reset
- *	@ap: ATA port
- *
- *	Perform the ATA probe and bus reset sequence plus specific handling
- *	for this hardware. The Opti needs little handling - we have no UDMA66
- *	capability that needs cable detection. All we must do is check the port
- *	is enabled.
- */
-
-static void opti_error_handler(struct ata_port *ap)
-{
-	ata_bmdma_drive_eh(ap, opti_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+	return ata_sff_prereset(link, deadline);
 }
 
 /**
@@ -165,58 +149,19 @@ static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
 }
 
 static struct scsi_host_template opti_sht = {
-	.module			= THIS_MODULE,
-	.name			= DRV_NAME,
-	.ioctl			= ata_scsi_ioctl,
-	.queuecommand		= ata_scsi_queuecmd,
-	.can_queue		= ATA_DEF_QUEUE,
-	.this_id		= ATA_SHT_THIS_ID,
-	.sg_tablesize		= LIBATA_MAX_PRD,
-	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
-	.emulated		= ATA_SHT_EMULATED,
-	.use_clustering		= ATA_SHT_USE_CLUSTERING,
-	.proc_name		= DRV_NAME,
-	.dma_boundary		= ATA_DMA_BOUNDARY,
-	.slave_configure	= ata_scsi_slave_config,
-	.slave_destroy		= ata_scsi_slave_destroy,
-	.bios_param		= ata_std_bios_param,
+	ATA_PIO_SHT(DRV_NAME),
 };
 
 static struct ata_port_operations opti_port_ops = {
-	.set_piomode	= opti_set_piomode,
-	.tf_load	= ata_tf_load,
-	.tf_read	= ata_tf_read,
-	.check_status 	= ata_check_status,
-	.exec_command	= ata_exec_command,
-	.dev_select 	= ata_std_dev_select,
-
-	.freeze		= ata_bmdma_freeze,
-	.thaw		= ata_bmdma_thaw,
-	.error_handler	= opti_error_handler,
-	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+	.inherits	= &ata_sff_port_ops,
 	.cable_detect	= ata_cable_40wire,
-
-	.bmdma_setup 	= ata_bmdma_setup,
-	.bmdma_start 	= ata_bmdma_start,
-	.bmdma_stop	= ata_bmdma_stop,
-	.bmdma_status 	= ata_bmdma_status,
-
-	.qc_prep 	= ata_qc_prep,
-	.qc_issue	= ata_qc_issue_prot,
-
-	.data_xfer	= ata_data_xfer,
-
-	.irq_handler	= ata_interrupt,
-	.irq_clear	= ata_bmdma_irq_clear,
-	.irq_on		= ata_irq_on,
-
-	.port_start	= ata_sff_port_start,
+	.set_piomode	= opti_set_piomode,
+	.prereset	= opti_pre_reset,
 };
 
 static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	static const struct ata_port_info info = {
-		.sht = &opti_sht,
 		.flags = ATA_FLAG_SLAVE_POSS,
 		.pio_mask = 0x1f,
 		.port_ops = &opti_port_ops
@@ -227,7 +172,7 @@ static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	if (!printed_version++)
 		dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
 
-	return ata_pci_init_one(dev, ppi);
+	return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL);
 }
 
 static const struct pci_device_id opti[] = {