X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fide%2Fide-iops.c;h=95168833d0691a82c896197a7a4d01beae361479;hb=0c326331c8b107abc0a160e8899d749150b8f76a;hp=cf0678b6116183ebf14e6108154b94955a4d4862;hpb=26bcb879c03254545a19c6700fe5bcef6f21e7b1;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index cf0678b6116..95168833d06 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -472,58 +472,23 @@ int drive_is_ready (ide_drive_t *drive)
 
 EXPORT_SYMBOL(drive_is_ready);
 
-/*
- * Global for All, and taken from ide-pmac.c. Can be called
- * with spinlock held & IRQs disabled, so don't schedule !
- */
-int wait_for_ready (ide_drive_t *drive, int timeout)
-{
-	ide_hwif_t *hwif	= HWIF(drive);
-	u8 stat			= 0;
-
-	while(--timeout) {
-		stat = hwif->INB(IDE_STATUS_REG);
-		if (!(stat & BUSY_STAT)) {
-			if (drive->ready_stat == 0)
-				break;
-			else if ((stat & drive->ready_stat)||(stat & ERR_STAT))
-				break;
-		}
-		mdelay(1);
-	}
-	if ((stat & ERR_STAT) || timeout <= 0) {
-		if (stat & ERR_STAT) {
-			printk(KERN_ERR "%s: wait_for_ready, "
-				"error status: %x\n", drive->name, stat);
-		}
-		return 1;
-	}
-	return 0;
-}
-
 /*
  * This routine busy-waits for the drive status to be not "busy".
  * It then checks the status for all of the "good" bits and none
  * of the "bad" bits, and if all is okay it returns 0.  All other
- * cases return 1 after invoking ide_error() -- caller should just return.
+ * cases return error -- caller may then invoke ide_error().
  *
  * This routine should get fixed to not hog the cpu during extra long waits..
  * That could be done by busy-waiting for the first jiffy or two, and then
  * setting a timer to wake up at half second intervals thereafter,
  * until timeout is achieved, before timing out.
  */
-int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+static int __ide_wait_stat(ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout, u8 *rstat)
 {
-	ide_hwif_t *hwif = HWIF(drive);
-	u8 stat;
-	int i;
+	ide_hwif_t *hwif = drive->hwif;
 	unsigned long flags;
- 
-	/* bail early if we've exceeded max_failures */
-	if (drive->max_failures && (drive->failures > drive->max_failures)) {
-		*startstop = ide_stopped;
-		return 1;
-	}
+	int i;
+	u8 stat;
 
 	udelay(1);	/* spec allows drive 400ns to assert "BUSY" */
 	if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
@@ -541,8 +506,8 @@ int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 b
 					break;
 
 				local_irq_restore(flags);
-				*startstop = ide_error(drive, "status timeout", stat);
-				return 1;
+				*rstat = stat;
+				return -EBUSY;
 			}
 		}
 		local_irq_restore(flags);
@@ -556,11 +521,39 @@ int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 b
 	 */
 	for (i = 0; i < 10; i++) {
 		udelay(1);
-		if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad))
+		if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad)) {
+			*rstat = stat;
 			return 0;
+		}
 	}
-	*startstop = ide_error(drive, "status error", stat);
-	return 1;
+	*rstat = stat;
+	return -EFAULT;
+}
+
+/*
+ * In case of error returns error value after doing "*startstop = ide_error()".
+ * The caller should return the updated value of "startstop" in this case,
+ * "startstop" is unchanged when the function returns 0.
+ */
+int ide_wait_stat(ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+{
+	int err;
+	u8 stat;
+
+	/* bail early if we've exceeded max_failures */
+	if (drive->max_failures && (drive->failures > drive->max_failures)) {
+		*startstop = ide_stopped;
+		return 1;
+	}
+
+	err = __ide_wait_stat(drive, good, bad, timeout, &stat);
+
+	if (err) {
+		char *s = (err == -EBUSY) ? "status timeout" : "status error";
+		*startstop = ide_error(drive, s, stat);
+	}
+
+	return err;
 }
 
 EXPORT_SYMBOL(ide_wait_stat);
@@ -620,15 +613,10 @@ u8 eighty_ninty_three (ide_drive_t *drive)
 
 	/*
 	 * FIXME:
-	 * - change master/slave IDENTIFY order
 	 * - force bit13 (80c cable present) check also for !ivb devices
 	 *   (unless the slave device is pre-ATA3)
 	 */
-#ifndef CONFIG_IDEDMA_IVB
 	if ((id->hw_config & 0x4000) || (ivb && (id->hw_config & 0x2000)))
-#else
-	if (id->hw_config & 0x6000)
-#endif
 		return 1;
 
 no_80w:
@@ -705,35 +693,16 @@ static u8 ide_auto_reduce_xfer (ide_drive_t *drive)
 }
 #endif /* CONFIG_BLK_DEV_IDEDMA */
 
-/*
- * Update the 
- */
-int ide_driveid_update (ide_drive_t *drive)
+int ide_driveid_update(ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= HWIF(drive);
+	ide_hwif_t *hwif = drive->hwif;
 	struct hd_driveid *id;
-#if 0
-	id = kmalloc(SECTOR_WORDS*4, GFP_ATOMIC);
-	if (!id)
-		return 0;
-
-	taskfile_lib_get_identify(drive, (char *)&id);
+	unsigned long timeout, flags;
 
-	ide_fix_driveid(id);
-	if (id) {
-		drive->id->dma_ultra = id->dma_ultra;
-		drive->id->dma_mword = id->dma_mword;
-		drive->id->dma_1word = id->dma_1word;
-		/* anything more ? */
-		kfree(id);
-	}
-	return 1;
-#else
 	/*
 	 * Re-read drive->id for possible DMA mode
 	 * change (copied from ide-probe.c)
 	 */
-	unsigned long timeout, flags;
 
 	SELECT_MASK(drive, 1);
 	if (IDE_CONTROL_REG)
@@ -775,25 +744,19 @@ int ide_driveid_update (ide_drive_t *drive)
 	}
 
 	return 1;
-#endif
 }
 
-/*
- * Similar to ide_wait_stat(), except it never calls ide_error internally.
- *
- * const char *msg == consider adding for verbose errors.
- */
-int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
+int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
 {
-	ide_hwif_t *hwif	= HWIF(drive);
-	int	i, error	= 1;
+	ide_hwif_t *hwif = drive->hwif;
+	int error;
 	u8 stat;
 
 //	while (HWGROUP(drive)->busy)
 //		msleep(50);
 
 #ifdef CONFIG_BLK_DEV_IDEDMA
-	if (hwif->ide_dma_check)	 /* check if host supports DMA */
+	if (hwif->ide_dma_on)	/* check if host supports DMA */
 		hwif->dma_host_off(drive);
 #endif
 
@@ -826,35 +789,10 @@ int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
 	hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
 	if ((IDE_CONTROL_REG) && (drive->quirk_list == 2))
 		hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
-	udelay(1);
-	/*
-	 * Wait for drive to become non-BUSY
-	 */
-	if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
-		unsigned long flags, timeout;
-		local_irq_set(flags);
-		timeout = jiffies + WAIT_CMD;
-		while ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
-			if (time_after(jiffies, timeout))
-				break;
-		}
-		local_irq_restore(flags);
-	}
 
-	/*
-	 * Allow status to settle, then read it again.
-	 * A few rare drives vastly violate the 400ns spec here,
-	 * so we'll wait up to 10usec for a "good" status
-	 * rather than expensively fail things immediately.
-	 * This fix courtesy of Matthew Faupel & Niccolo Rigacci.
-	 */
-	for (i = 0; i < 10; i++) {
-		udelay(1);
-		if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), drive->ready_stat, BUSY_STAT|DRQ_STAT|ERR_STAT)) {
-			error = 0;
-			break;
-		}
-	}
+	error = __ide_wait_stat(drive, drive->ready_stat,
+				BUSY_STAT|DRQ_STAT|ERR_STAT,
+				WAIT_CMD, &stat);
 
 	SELECT_MASK(drive, 0);
 
@@ -872,7 +810,7 @@ int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
 #ifdef CONFIG_BLK_DEV_IDEDMA
 	if (speed >= XFER_SW_DMA_0)
 		hwif->dma_host_on(drive);
-	else if (hwif->ide_dma_check)	/* check if host supports DMA */
+	else if (hwif->ide_dma_on)	/* check if host supports DMA */
 		hwif->dma_off_quietly(drive);
 #endif
 
@@ -899,9 +837,6 @@ int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
 	return error;
 }
 
-EXPORT_SYMBOL(ide_config_drive_speed);
-
-
 /*
  * This should get invoked any time we exit the driver to
  * wait for an interrupt response from a drive.  handler() points