X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Finfiniband%2Fhw%2Fipath%2Fipath_iba6110.c;h=8e0794d316fb69a9fbe7886447af75ef8c92c821;hb=27b044a815df7d4530bc68560796680ed588070c;hp=9e4e8d4c6e2035769ddef2a080a1f7163bef8678;hpb=0cd43f83d381c4246a08cd775834833d6fd64805;p=linux-2.6-omap-h63xx.git diff --git a/drivers/infiniband/hw/ipath/ipath_iba6110.c b/drivers/infiniband/hw/ipath/ipath_iba6110.c index 9e4e8d4c6e2..8e0794d316f 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6110.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c @@ -38,6 +38,7 @@ #include #include +#include #include "ipath_kernel.h" #include "ipath_registers.h" @@ -207,8 +208,8 @@ static const struct ipath_kregs ipath_ht_kregs = { .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus), .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig), /* - * These should not be used directly via ipath_read_kreg64(), - * use them with ipath_read_kreg64_port(), + * These should not be used directly via ipath_write_kreg64(), + * use them with ipath_write_kreg64_port(), */ .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0), .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0) @@ -283,6 +284,14 @@ static const struct ipath_cregs ipath_ht_cregs = { #define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 #define INFINIPATH_EXTS_MEMBIST_CORRECT 0x0000000000008000 + +/* TID entries (memory), HT-only */ +#define INFINIPATH_RT_ADDR_MASK 0xFFFFFFFFFFULL /* 40 bits valid */ +#define INFINIPATH_RT_VALID 0x8000000000000000ULL +#define INFINIPATH_RT_ADDR_SHIFT 0 +#define INFINIPATH_RT_BUFSIZE_MASK 0x3FFFULL +#define INFINIPATH_RT_BUFSIZE_SHIFT 48 + /* * masks and bits that are different in different chips, or present only * in one @@ -401,6 +410,14 @@ static const struct ipath_hwerror_msgs ipath_6110_hwerror_msgs[] = { INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"), }; +#define TXE_PIO_PARITY ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | \ + INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) \ + << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) +#define RXE_EAGER_PARITY (INFINIPATH_HWE_RXEMEMPARITYERR_EAGERTID \ + << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) + +static int ipath_ht_txe_recover(struct ipath_devdata *); + /** * ipath_ht_handle_hwerrors - display hardware errors. * @dd: the infinipath device @@ -449,13 +466,12 @@ static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg, /* * make sure we get this much out, unless told to be quiet, + * it's a parity error we may recover from, * or it's occurred within the last 5 seconds */ - if ((hwerrs & ~(dd->ipath_lasthwerror | - ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) || - (ipath_debug & __IPATH_VERBDBG)) + if ((hwerrs & ~(dd->ipath_lasthwerror | TXE_PIO_PARITY | + RXE_EAGER_PARITY)) || + (ipath_debug & __IPATH_VERBDBG)) dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx " "(cleared)\n", (unsigned long long) hwerrs); dd->ipath_lasthwerror |= hwerrs; @@ -466,7 +482,7 @@ static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg, (hwerrs & ~dd->ipath_hwe_bitsextant)); ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control); - if (ctrl & INFINIPATH_C_FREEZEMODE) { + if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) { /* * parity errors in send memory are recoverable, * just cancel the send (if indicated in * sendbuffererror), @@ -475,50 +491,14 @@ static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg, * occur if a processor speculative read is done to the PIO * buffer while we are sending a packet, for example. */ - if (hwerrs & ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) { - ipath_stats.sps_txeparity++; - ipath_dbg("Recovering from TXE parity error (%llu), " - "hwerrstatus=%llx\n", - (unsigned long long) ipath_stats.sps_txeparity, - (unsigned long long) hwerrs); - ipath_disarm_senderrbufs(dd); - hwerrs &= ~((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT); - if (!hwerrs) { /* else leave in freeze mode */ - ipath_write_kreg(dd, - dd->ipath_kregs->kr_control, - dd->ipath_control); - return; - } - } - if (hwerrs) { - /* - * if any set that we aren't ignoring; only - * make the complaint once, in case it's stuck - * or recurring, and we get here multiple - * times. - */ - if (dd->ipath_flags & IPATH_INITTED) { - ipath_dev_err(dd, "Fatal Hardware Error (freeze " - "mode), no longer usable, SN %.16s\n", - dd->ipath_serial); - isfatal = 1; - } - *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY; - /* mark as having had error */ - *dd->ipath_statusp |= IPATH_STATUS_HWERROR; - /* - * mark as not usable, at a minimum until driver - * is reloaded, probably until reboot, since no - * other reset is possible. - */ - dd->ipath_flags &= ~IPATH_INITTED; - } else { - ipath_dbg("Clearing freezemode on ignored hardware " - "error\n"); + if ((hwerrs & TXE_PIO_PARITY) && ipath_ht_txe_recover(dd)) + hwerrs &= ~TXE_PIO_PARITY; + if (hwerrs & RXE_EAGER_PARITY) + ipath_dev_err(dd, "RXE parity, Eager TID error is not " + "recoverable\n"); + if (!hwerrs) { + ipath_dbg("Clearing freezemode on ignored or " + "recovered hardware error\n"); ctrl &= ~INFINIPATH_C_FREEZEMODE; ipath_write_kreg(dd, dd->ipath_kregs->kr_control, ctrl); @@ -586,7 +566,32 @@ static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg, dd->ipath_hwerrmask); } - ipath_dev_err(dd, "%s hardware error\n", msg); + if (hwerrs) { + /* + * if any set that we aren't ignoring; only + * make the complaint once, in case it's stuck + * or recurring, and we get here multiple + * times. + */ + ipath_dev_err(dd, "%s hardware error\n", msg); + if (dd->ipath_flags & IPATH_INITTED) { + ipath_dev_err(dd, "Fatal Hardware Error (freeze " + "mode), no longer usable, SN %.16s\n", + dd->ipath_serial); + isfatal = 1; + } + *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY; + /* mark as having had error */ + *dd->ipath_statusp |= IPATH_STATUS_HWERROR; + /* + * mark as not usable, at a minimum until driver + * is reloaded, probably until reboot, since no + * other reset is possible. + */ + dd->ipath_flags &= ~IPATH_INITTED; + } + else + *msg = 0; /* recovered from all of them */ if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) /* * for status file; if no trailing brace is copied, @@ -657,7 +662,8 @@ static int ipath_ht_boardname(struct ipath_devdata *dd, char *name, if (n) snprintf(name, namelen, "%s", n); - if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || dd->ipath_minrev > 3)) { + if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || + dd->ipath_minrev > 3)) { /* * This version of the driver only supports Rev 3.2 and 3.3 */ @@ -913,49 +919,40 @@ static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev, } } -static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, - int pos) +static int ipath_ht_intconfig(struct ipath_devdata *dd) { - u32 int_handler_addr_lower; - u32 int_handler_addr_upper; - u64 ihandler; - u32 intvec; + int ret; + + if (dd->ipath_intconfig) { + ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, + dd->ipath_intconfig); /* interrupt address */ + ret = 0; + } else { + ipath_dev_err(dd, "No interrupts enabled, couldn't setup " + "interrupt address\n"); + ret = -EINVAL; + } + + return ret; +} - /* use indirection register to get the intr handler */ - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower); - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper); +static void ipath_ht_irq_update(struct pci_dev *dev, int irq, + struct ht_irq_msg *msg) +{ + struct ipath_devdata *dd = pci_get_drvdata(dev); + u64 prev_intconfig = dd->ipath_intconfig; - ihandler = (u64) int_handler_addr_lower | - ((u64) int_handler_addr_upper << 32); + dd->ipath_intconfig = msg->address_lo; + dd->ipath_intconfig |= ((u64) msg->address_hi) << 32; /* - * kernels with CONFIG_PCI_MSI set the vector in the irq field of - * struct pci_device, so we use that to program the internal - * interrupt register (not config space) with that value. The BIOS - * must still have done the basic MSI setup. - */ - intvec = pdev->irq; - /* - * clear any vector bits there; normally not set but we'll overload - * this for some debug purposes (setting the HTC debug register - * value from software, rather than GPIOs), so it might be set on a - * driver reload. + * If the previous value of dd->ipath_intconfig is zero, we're + * getting configured for the first time, and must not program the + * intconfig register here (it will be programmed later, when the + * hardware is ready). Otherwise, we should. */ - ihandler &= ~0xff0000; - /* x86 vector goes in intrinfo[23:16] */ - ihandler |= intvec << 16; - ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, " - "interruptconfig %llx\n", int_handler_addr_lower, - int_handler_addr_upper, intvec, - (unsigned long long) ihandler); - - /* can't program yet, so save for interrupt setup */ - dd->ipath_intconfig = ihandler; - /* keep going, so we find link control stuff also */ - - return ihandler != 0; + if (prev_intconfig) + ipath_ht_intconfig(dd); } /** @@ -971,12 +968,19 @@ static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, static int ipath_setup_ht_config(struct ipath_devdata *dd, struct pci_dev *pdev) { - int pos, ret = 0; - int ihandler = 0; + int pos, ret; + + ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update); + if (ret < 0) { + ipath_dev_err(dd, "Couldn't create interrupt handler: " + "err %d\n", ret); + goto bail; + } + dd->ipath_irq = ret; + ret = 0; /* - * Read the capability info to find the interrupt info, and also - * handle clearing CRC errors in linkctrl register if necessary. We + * Handle clearing CRC errors in linkctrl register if necessary. We * do this early, before we ever enable errors or hardware errors, * mostly to avoid causing the chip to enter freeze mode. */ @@ -1000,17 +1004,9 @@ static int ipath_setup_ht_config(struct ipath_devdata *dd, } if (!(cap_type & 0xE0)) slave_or_pri_blk(dd, pdev, pos, cap_type); - else if (cap_type == HT_INTR_DISC_CONFIG) - ihandler = set_int_handler(dd, pdev, pos); } while ((pos = pci_find_next_capability(pdev, pos, PCI_CAP_ID_HT))); - if (!ihandler) { - ipath_dev_err(dd, "Couldn't find interrupt handler in " - "config space\n"); - ret = -ENODEV; - } - bail: return ret; } @@ -1172,6 +1168,8 @@ static void ipath_ht_init_hwerrors(struct ipath_devdata *dd) if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST)) ipath_dev_err(dd, "MemBIST did not complete!\n"); + if (extsval & INFINIPATH_EXTS_MEMBIST_CORRECT) + ipath_dbg("MemBIST corrected\n"); ipath_check_htlink(dd); @@ -1360,25 +1358,6 @@ static void ipath_ht_quiet_serdes(struct ipath_devdata *dd) ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val); } -static int ipath_ht_intconfig(struct ipath_devdata *dd) -{ - int ret; - - if (!dd->ipath_intconfig) { - ipath_dev_err(dd, "No interrupts enabled, couldn't setup " - "interrupt address\n"); - ret = 1; - goto bail; - } - - ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, - dd->ipath_intconfig); /* interrupt address */ - ret = 0; - -bail: - return ret; -} - /** * ipath_pe_put_tid - write a TID in chip * @dd: the infinipath device @@ -1394,6 +1373,9 @@ static void ipath_ht_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, u32 type, unsigned long pa) { + if (!dd->ipath_kregbase) + return; + if (pa != dd->ipath_tidinvalid) { if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) { dev_info(&dd->pcidev->dev, @@ -1410,10 +1392,10 @@ static void ipath_ht_put_tid(struct ipath_devdata *dd, pa |= lenvalid | INFINIPATH_RT_VALID; } } - if (dd->ipath_kregbase) - writeq(pa, tidptr); + writeq(pa, tidptr); } + /** * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager * @dd: the infinipath device @@ -1475,7 +1457,7 @@ static void ipath_ht_tidtemplate(struct ipath_devdata *dd) static int ipath_ht_early_init(struct ipath_devdata *dd) { u32 __iomem *piobuf; - u32 pioincr, val32, egrsize; + u32 pioincr, val32; int i; /* @@ -1495,7 +1477,6 @@ static int ipath_ht_early_init(struct ipath_devdata *dd) * errors interrupts if we ever see one). */ dd->ipath_rcvegrbufsize = dd->ipath_piosize2k; - egrsize = dd->ipath_rcvegrbufsize; /* * the min() check here is currently a nop, but it may not @@ -1544,7 +1525,7 @@ static int ipath_ht_early_init(struct ipath_devdata *dd) INFINIPATH_S_ABORT); ipath_get_eeprom_info(dd); - if(dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' && + if (dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' && dd->ipath_serial[1] == '2' && dd->ipath_serial[2] == '8') { /* * Later production QHT7040 has same changes as QHT7140, so @@ -1557,13 +1538,31 @@ static int ipath_ht_early_init(struct ipath_devdata *dd) return 0; } + +static int ipath_ht_txe_recover(struct ipath_devdata *dd) +{ + int cnt = ++ipath_stats.sps_txeparity; + if (cnt >= IPATH_MAX_PARITY_ATTEMPTS) { + if (cnt == IPATH_MAX_PARITY_ATTEMPTS) + ipath_dev_err(dd, + "Too many attempts to recover from " + "TXE parity, giving up\n"); + return 0; + } + dev_info(&dd->pcidev->dev, + "Recovering from TXE PIO parity error\n"); + ipath_disarm_senderrbufs(dd, 1); + return 1; +} + + /** * ipath_init_ht_get_base_info - set chip-specific flags for user code * @dd: the infinipath device * @kbase: ipath_base_info pointer * * We set the PCIE flag because the lower bandwidth on PCIe vs - * HyperTransport can affect some user packet algorithims. + * HyperTransport can affect some user packet algorithms. */ static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase) { @@ -1575,6 +1574,14 @@ static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase) return 0; } +static void ipath_ht_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + ht_destroy_irq(dd->ipath_irq); + dd->ipath_irq = 0; + dd->ipath_intconfig = 0; +} + /** * ipath_init_iba6110_funcs - set up the chip-specific function pointers * @dd: the infinipath device @@ -1598,6 +1605,7 @@ void ipath_init_iba6110_funcs(struct ipath_devdata *dd) dd->ipath_f_cleanup = ipath_setup_ht_cleanup; dd->ipath_f_setextled = ipath_setup_ht_setextled; dd->ipath_f_get_base_info = ipath_ht_get_base_info; + dd->ipath_f_free_irq = ipath_ht_free_irq; /* * initialize chip-specific variables