X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Finput%2Fserio%2Fi8042.c;h=170f71ee5772cda51f08298ccf7dd779ffa14bba;hb=a8cac817764a494705aebd99fd51bdf6cdc28ec9;hp=65a74cfc187b12199bb3f291775e9223da504198;hpb=62429f434091586d54b37b8dd46076e7c08b27b9;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/input/serio/i8042.c b/drivers/input/serio/i8042.c
index 65a74cfc187..170f71ee577 100644
--- a/drivers/input/serio/i8042.c
+++ b/drivers/input/serio/i8042.c
@@ -885,6 +885,20 @@ static long i8042_panic_blink(long count)
 
 #undef DELAY
 
+#ifdef CONFIG_X86
+static void i8042_dritek_enable(void)
+{
+	char param = 0x90;
+	int error;
+
+	error = i8042_command(&param, 0x1059);
+	if (error)
+		printk(KERN_WARNING
+			"Failed to enable DRITEK extension: %d\n",
+			error);
+}
+#endif
+
 #ifdef CONFIG_PM
 /*
  * Here we try to restore the original BIOS settings. We only want to
@@ -938,10 +952,20 @@ static int i8042_resume(struct platform_device *dev)
 	i8042_ctr |= I8042_CTR_AUXDIS | I8042_CTR_KBDDIS;
 	i8042_ctr &= ~(I8042_CTR_AUXINT | I8042_CTR_KBDINT);
 	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
-		printk(KERN_ERR "i8042: Can't write CTR to resume\n");
-		return -EIO;
+		printk(KERN_WARNING "i8042: Can't write CTR to resume, retrying...\n");
+		msleep(50);
+		if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
+			printk(KERN_ERR "i8042: CTR write retry failed\n");
+			return -EIO;
+		}
 	}
 
+
+#ifdef CONFIG_X86
+	if (i8042_dritek)
+		i8042_dritek_enable();
+#endif
+
 	if (i8042_mux_present) {
 		if (i8042_set_mux_mode(1, NULL) || i8042_enable_mux_ports())
 			printk(KERN_WARNING
@@ -1160,6 +1184,11 @@ static int __devinit i8042_probe(struct platform_device *dev)
 	if (error)
 		return error;
 
+#ifdef CONFIG_X86
+	if (i8042_dritek)
+		i8042_dritek_enable();
+#endif
+
 	if (!i8042_noaux) {
 		error = i8042_setup_aux();
 		if (error && error != -ENODEV && error != -EBUSY)
@@ -1171,14 +1200,6 @@ static int __devinit i8042_probe(struct platform_device *dev)
 		if (error)
 			goto out_fail;
 	}
-#ifdef CONFIG_X86
-	if (i8042_dritek) {
-		char param = 0x90;
-		error = i8042_command(&param, 0x1059);
-		if (error)
-			goto out_fail;
-	}
-#endif
 /*
  * Ok, everything is ready, let's register all serio ports
  */