X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fmfd%2Fsm501.c;h=e2530df4d85cb00bed8d36825546bc837f531b8e;hb=4f46d6e7e5ffbce0ee1d1a80767fdf45e56cc863;hp=afd82966f9a0782ad5624f45fcf4538e3755a73f;hpb=acf63867ae06ef95eea7bf445ded2f05528a81b1;p=linux-2.6-omap-h63xx.git diff --git a/drivers/mfd/sm501.c b/drivers/mfd/sm501.c index afd82966f9a..e2530df4d85 100644 --- a/drivers/mfd/sm501.c +++ b/drivers/mfd/sm501.c @@ -22,6 +22,7 @@ #include #include +#include #include @@ -48,31 +49,13 @@ struct sm501_devdata { unsigned int pdev_id; unsigned int irq; void __iomem *regs; + unsigned int rev; }; #define MHZ (1000 * 1000) #ifdef DEBUG -static const unsigned int misc_div[] = { - [0] = 1, - [1] = 2, - [2] = 4, - [3] = 8, - [4] = 16, - [5] = 32, - [6] = 64, - [7] = 128, - [8] = 3, - [9] = 6, - [10] = 12, - [11] = 24, - [12] = 48, - [13] = 96, - [14] = 192, - [15] = 384, -}; - -static const unsigned int px_div[] = { +static const unsigned int div_tab[] = { [0] = 1, [1] = 2, [2] = 4, @@ -101,12 +84,12 @@ static const unsigned int px_div[] = { static unsigned long decode_div(unsigned long pll2, unsigned long val, unsigned int lshft, unsigned int selbit, - unsigned long mask, const unsigned int *dtab) + unsigned long mask) { if (val & selbit) pll2 = 288 * MHZ; - return pll2 / dtab[(val >> lshft) & mask]; + return pll2 / div_tab[(val >> lshft) & mask]; } #define fmt_freq(x) ((x) / MHZ), ((x) % MHZ), (x) @@ -141,10 +124,10 @@ static void sm501_dump_clk(struct sm501_devdata *sm) } sdclk0 = (misct & (1<<12)) ? pll2 : 288 * MHZ; - sdclk0 /= misc_div[((misct >> 8) & 0xf)]; + sdclk0 /= div_tab[((misct >> 8) & 0xf)]; sdclk1 = (misct & (1<<20)) ? pll2 : 288 * MHZ; - sdclk1 /= misc_div[((misct >> 16) & 0xf)]; + sdclk1 /= div_tab[((misct >> 16) & 0xf)]; dev_dbg(sm->dev, "MISCT=%08lx, PM0=%08lx, PM1=%08lx\n", misct, pm0, pm1); @@ -158,19 +141,19 @@ static void sm501_dump_clk(struct sm501_devdata *sm) "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), " "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", (pmc & 3 ) == 0 ? '*' : '-', - fmt_freq(decode_div(pll2, pm0, 24, 1<<29, 31, px_div)), - fmt_freq(decode_div(pll2, pm0, 16, 1<<20, 15, misc_div)), - fmt_freq(decode_div(pll2, pm0, 8, 1<<12, 15, misc_div)), - fmt_freq(decode_div(pll2, pm0, 0, 1<<4, 15, misc_div))); + fmt_freq(decode_div(pll2, pm0, 24, 1<<29, 31)), + fmt_freq(decode_div(pll2, pm0, 16, 1<<20, 15)), + fmt_freq(decode_div(pll2, pm0, 8, 1<<12, 15)), + fmt_freq(decode_div(pll2, pm0, 0, 1<<4, 15))); dev_dbg(sm->dev, "PM1[%c]: " "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), " "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n", (pmc & 3 ) == 1 ? '*' : '-', - fmt_freq(decode_div(pll2, pm1, 24, 1<<29, 31, px_div)), - fmt_freq(decode_div(pll2, pm1, 16, 1<<20, 15, misc_div)), - fmt_freq(decode_div(pll2, pm1, 8, 1<<12, 15, misc_div)), - fmt_freq(decode_div(pll2, pm1, 0, 1<<4, 15, misc_div))); + fmt_freq(decode_div(pll2, pm1, 24, 1<<29, 31)), + fmt_freq(decode_div(pll2, pm1, 16, 1<<20, 15)), + fmt_freq(decode_div(pll2, pm1, 8, 1<<12, 15)), + fmt_freq(decode_div(pll2, pm1, 0, 1<<4, 15))); } static void sm501_dump_regs(struct sm501_devdata *sm) @@ -366,11 +349,11 @@ int sm501_unit_power(struct device *dev, unsigned int unit, unsigned int to) mode &= 3; /* get current power mode */ if (unit >= ARRAY_SIZE(sm->unit_power)) { - dev_err(dev, "%s: bad unit %d\n", __FUNCTION__, unit); + dev_err(dev, "%s: bad unit %d\n", __func__, unit); goto already; } - dev_dbg(sm->dev, "%s: unit %d, cur %d, to %d\n", __FUNCTION__, unit, + dev_dbg(sm->dev, "%s: unit %d, cur %d, to %d\n", __func__, unit, sm->unit_power[unit], to); if (to == 0 && sm->unit_power[unit] == 0) { @@ -436,46 +419,108 @@ struct sm501_clock { unsigned long mclk; int divider; int shift; + unsigned int m, n, k; }; +/* sm501_calc_clock + * + * Calculates the nearest discrete clock frequency that + * can be achieved with the specified input clock. + * the maximum divisor is 3 or 5 + */ + +static int sm501_calc_clock(unsigned long freq, + struct sm501_clock *clock, + int max_div, + unsigned long mclk, + long *best_diff) +{ + int ret = 0; + int divider; + int shift; + long diff; + + /* try dividers 1 and 3 for CRT and for panel, + try divider 5 for panel only.*/ + + for (divider = 1; divider <= max_div; divider += 2) { + /* try all 8 shift values.*/ + for (shift = 0; shift < 8; shift++) { + /* Calculate difference to requested clock */ + diff = sm501fb_round_div(mclk, divider << shift) - freq; + if (diff < 0) + diff = -diff; + + /* If it is less than the current, use it */ + if (diff < *best_diff) { + *best_diff = diff; + + clock->mclk = mclk; + clock->divider = divider; + clock->shift = shift; + ret = 1; + } + } + } + + return ret; +} + +/* sm501_calc_pll + * + * Calculates the nearest discrete clock frequency that can be + * achieved using the programmable PLL. + * the maximum divisor is 3 or 5 + */ + +static unsigned long sm501_calc_pll(unsigned long freq, + struct sm501_clock *clock, + int max_div) +{ + unsigned long mclk; + unsigned int m, n, k; + long best_diff = 999999999; + + /* + * The SM502 datasheet doesn't specify the min/max values for M and N. + * N = 1 at least doesn't work in practice. + */ + for (m = 2; m <= 255; m++) { + for (n = 2; n <= 127; n++) { + for (k = 0; k <= 1; k++) { + mclk = (24000000UL * m / n) >> k; + + if (sm501_calc_clock(freq, clock, max_div, + mclk, &best_diff)) { + clock->m = m; + clock->n = n; + clock->k = k; + } + } + } + } + + /* Return best clock. */ + return clock->mclk / (clock->divider << clock->shift); +} + /* sm501_select_clock * - * selects nearest discrete clock frequency the SM501 can achive + * Calculates the nearest discrete clock frequency that can be + * achieved using the 288MHz and 336MHz PLLs. * the maximum divisor is 3 or 5 */ + static unsigned long sm501_select_clock(unsigned long freq, struct sm501_clock *clock, int max_div) { unsigned long mclk; - int divider; - int shift; - long diff; long best_diff = 999999999; /* Try 288MHz and 336MHz clocks. */ for (mclk = 288000000; mclk <= 336000000; mclk += 48000000) { - /* try dividers 1 and 3 for CRT and for panel, - try divider 5 for panel only.*/ - - for (divider = 1; divider <= max_div; divider += 2) { - /* try all 8 shift values.*/ - for (shift = 0; shift < 8; shift++) { - /* Calculate difference to requested clock */ - diff = sm501fb_round_div(mclk, divider << shift) - freq; - if (diff < 0) - diff = -diff; - - /* If it is less than the current, use it */ - if (diff < best_diff) { - best_diff = diff; - - clock->mclk = mclk; - clock->divider = divider; - clock->shift = shift; - } - } - } + sm501_calc_clock(freq, clock, max_div, mclk, &best_diff); } /* Return best clock. */ @@ -497,6 +542,7 @@ unsigned long sm501_set_clock(struct device *dev, unsigned long gate = readl(sm->regs + SM501_CURRENT_GATE); unsigned long clock = readl(sm->regs + SM501_CURRENT_CLOCK); unsigned char reg; + unsigned int pll_reg = 0; unsigned long sm501_freq; /* the actual frequency acheived */ struct sm501_clock to; @@ -511,14 +557,28 @@ unsigned long sm501_set_clock(struct device *dev, * requested frequency the value must be multiplied by * 2. This clock also has an additional pre divisor */ - sm501_freq = (sm501_select_clock(2 * req_freq, &to, 5) / 2); - reg=to.shift & 0x07;/* bottom 3 bits are shift */ - if (to.divider == 3) - reg |= 0x08; /* /3 divider required */ - else if (to.divider == 5) - reg |= 0x10; /* /5 divider required */ - if (to.mclk != 288000000) - reg |= 0x20; /* which mclk pll is source */ + if (sm->rev >= 0xC0) { + /* SM502 -> use the programmable PLL */ + sm501_freq = (sm501_calc_pll(2 * req_freq, + &to, 5) / 2); + reg = to.shift & 0x07;/* bottom 3 bits are shift */ + if (to.divider == 3) + reg |= 0x08; /* /3 divider required */ + else if (to.divider == 5) + reg |= 0x10; /* /5 divider required */ + reg |= 0x40; /* select the programmable PLL */ + pll_reg = 0x20000 | (to.k << 15) | (to.n << 8) | to.m; + } else { + sm501_freq = (sm501_select_clock(2 * req_freq, + &to, 5) / 2); + reg = to.shift & 0x07;/* bottom 3 bits are shift */ + if (to.divider == 3) + reg |= 0x08; /* /3 divider required */ + else if (to.divider == 5) + reg |= 0x10; /* /5 divider required */ + if (to.mclk != 288000000) + reg |= 0x20; /* which mclk pll is source */ + } break; case SM501_CLOCK_V2XCLK: @@ -579,6 +639,10 @@ unsigned long sm501_set_clock(struct device *dev, } writel(mode, sm->regs + SM501_POWER_MODE_CONTROL); + + if (pll_reg) + writel(pll_reg, sm->regs + SM501_PROGRAMMABLE_PLL_CONTROL); + sm501_sync_regs(sm); dev_info(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n", @@ -599,15 +663,24 @@ EXPORT_SYMBOL_GPL(sm501_set_clock); * finds the closest available frequency for a given clock */ -unsigned long sm501_find_clock(int clksrc, +unsigned long sm501_find_clock(struct device *dev, + int clksrc, unsigned long req_freq) { + struct sm501_devdata *sm = dev_get_drvdata(dev); unsigned long sm501_freq; /* the frequency achiveable by the 501 */ struct sm501_clock to; switch (clksrc) { case SM501_CLOCK_P2XCLK: - sm501_freq = (sm501_select_clock(2 * req_freq, &to, 5) / 2); + if (sm->rev >= 0xC0) { + /* SM502 -> use the programmable PLL */ + sm501_freq = (sm501_calc_pll(2 * req_freq, + &to, 5) / 2); + } else { + sm501_freq = (sm501_select_clock(2 * req_freq, + &to, 5) / 2); + } break; case SM501_CLOCK_V2XCLK: @@ -651,13 +724,14 @@ static void sm501_device_release(struct device *dev) */ static struct platform_device * -sm501_create_subdev(struct sm501_devdata *sm, - char *name, unsigned int res_count) +sm501_create_subdev(struct sm501_devdata *sm, char *name, + unsigned int res_count, unsigned int platform_data_size) { struct sm501_device *smdev; smdev = kzalloc(sizeof(struct sm501_device) + - sizeof(struct resource) * res_count, GFP_KERNEL); + (sizeof(struct resource) * res_count) + + platform_data_size, GFP_KERNEL); if (!smdev) return NULL; @@ -665,11 +739,15 @@ sm501_create_subdev(struct sm501_devdata *sm, smdev->pdev.name = name; smdev->pdev.id = sm->pdev_id; - smdev->pdev.resource = (struct resource *)(smdev+1); - smdev->pdev.num_resources = res_count; - smdev->pdev.dev.parent = sm->dev; + if (res_count) { + smdev->pdev.resource = (struct resource *)(smdev+1); + smdev->pdev.num_resources = res_count; + } + if (platform_data_size) + smdev->pdev.dev.platform_data = (void *)(smdev+1); + return &smdev->pdev; } @@ -757,7 +835,7 @@ static int sm501_register_usbhost(struct sm501_devdata *sm, { struct platform_device *pdev; - pdev = sm501_create_subdev(sm, "sm501-usb", 3); + pdev = sm501_create_subdev(sm, "sm501-usb", 3, 0); if (!pdev) return -ENOMEM; @@ -768,12 +846,55 @@ static int sm501_register_usbhost(struct sm501_devdata *sm, return sm501_register_device(sm, pdev); } +static void sm501_setup_uart_data(struct sm501_devdata *sm, + struct plat_serial8250_port *uart_data, + unsigned int offset) +{ + uart_data->membase = sm->regs + offset; + uart_data->mapbase = sm->io_res->start + offset; + uart_data->iotype = UPIO_MEM; + uart_data->irq = sm->irq; + uart_data->flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ; + uart_data->regshift = 2; + uart_data->uartclk = (9600 * 16); +} + +static int sm501_register_uart(struct sm501_devdata *sm, int devices) +{ + struct platform_device *pdev; + struct plat_serial8250_port *uart_data; + + pdev = sm501_create_subdev(sm, "serial8250", 0, + sizeof(struct plat_serial8250_port) * 3); + if (!pdev) + return -ENOMEM; + + uart_data = pdev->dev.platform_data; + + if (devices & SM501_USE_UART0) { + sm501_setup_uart_data(sm, uart_data++, 0x30000); + sm501_unit_power(sm->dev, SM501_GATE_UART0, 1); + sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 12, 0); + sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x01e0, 0); + } + if (devices & SM501_USE_UART1) { + sm501_setup_uart_data(sm, uart_data++, 0x30020); + sm501_unit_power(sm->dev, SM501_GATE_UART1, 1); + sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 13, 0); + sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x1e00, 0); + } + + pdev->id = PLAT8250_DEV_SM501; + + return sm501_register_device(sm, pdev); +} + static int sm501_register_display(struct sm501_devdata *sm, resource_size_t *mem_avail) { struct platform_device *pdev; - pdev = sm501_create_subdev(sm, "sm501-fb", 4); + pdev = sm501_create_subdev(sm, "sm501-fb", 4, 0); if (!pdev) return -ENOMEM; @@ -891,6 +1012,7 @@ static unsigned int sm501_mem_local[] = { static int sm501_init_dev(struct sm501_devdata *sm) { + struct sm501_initdata *idata; resource_size_t mem_avail; unsigned long dramctrl; unsigned long devid; @@ -908,12 +1030,17 @@ static int sm501_init_dev(struct sm501_devdata *sm) return -EINVAL; } + /* disable irqs */ + writel(0, sm->regs + SM501_IRQ_MASK); + dramctrl = readl(sm->regs + SM501_DRAM_CONTROL); mem_avail = sm501_mem_local[(dramctrl >> 13) & 0x7]; dev_info(sm->dev, "SM501 At %p: Version %08lx, %ld Mb, IRQ %d\n", sm->regs, devid, (unsigned long)mem_avail >> 20, sm->irq); + sm->rev = devid & SM501_DEVICEID_REVMASK; + sm501_dump_gate(sm); ret = device_create_file(sm->dev, &dev_attr_dbg_regs); @@ -924,15 +1051,14 @@ static int sm501_init_dev(struct sm501_devdata *sm) /* check to see if we have some device initialisation */ - if (sm->platdata) { - struct sm501_platdata *pdata = sm->platdata; - - if (pdata->init) { - sm501_init_regs(sm, sm->platdata->init); + idata = sm->platdata ? sm->platdata->init : NULL; + if (idata) { + sm501_init_regs(sm, idata); - if (pdata->init->devices & SM501_USE_USB_HOST) - sm501_register_usbhost(sm, &mem_avail); - } + if (idata->devices & SM501_USE_USB_HOST) + sm501_register_usbhost(sm, &mem_avail); + if (idata->devices & (SM501_USE_UART0 | SM501_USE_UART1)) + sm501_register_uart(sm, idata->devices); } ret = sm501_check_clocks(sm); @@ -1252,6 +1378,8 @@ static struct pci_driver sm501_pci_drv = { .remove = sm501_pci_remove, }; +MODULE_ALIAS("platform:sm501"); + static struct platform_driver sm501_plat_drv = { .driver = { .name = "sm501",