X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fnet%2FKconfig;h=b034410b7ab63e520143cdd527dcb9f17bb4f0d5;hb=93ab8e84dec242b868ec2e2ae42cb55a46b8c598;hp=d9107e542dface363ef53d71339361d99f7619de;hpb=f589b86d4b6e067b720a253bdb40896857804037;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index d9107e542df..b034410b7ab 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -166,16 +166,6 @@ config NET_SB1000
 
 	  If you don't have this card, of course say N.
 
-config IP1000
-	tristate "IP1000 Gigabit Ethernet support"
-	depends on PCI && EXPERIMENTAL
-	select MII
-	---help---
-	  This driver supports IP1000 gigabit Ethernet cards.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called ipg.  This is recommended.
-
 source "drivers/net/arcnet/Kconfig"
 
 source "drivers/net/phy/Kconfig"
@@ -222,7 +212,7 @@ config MII
 
 config MACB
 	tristate "Atmel MACB support"
-	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
+	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9
 	select PHYLIB
 	help
 	  The Atmel MACB ethernet interface is found on many AT32 and AT91
@@ -1594,6 +1584,18 @@ config 8139_OLD_RX_RESET
 	  experience problems, you can enable this option to restore the
 	  old RX-reset behavior.  If unsure, say N.
 
+config R6040
+	tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
+	depends on NET_PCI && PCI
+	select CRC32
+	select MII
+	help
+	  This is a driver for the R6040 Fast Ethernet MACs found in the
+	  the RDC R-321x System-on-chips.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called r6040. This is recommended.
+
 config SIS900
 	tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
 	depends on NET_PCI && PCI
@@ -1986,12 +1988,19 @@ config E1000E
 
 	  <http://support.intel.com>
 
-	  More specific information on configuring the driver is in
-	  <file:Documentation/networking/e1000e.txt>.
-
 	  To compile this driver as a module, choose M here. The module
 	  will be called e1000e.
 
+config IP1000
+	tristate "IP1000 Gigabit Ethernet support"
+	depends on PCI && EXPERIMENTAL
+	select MII
+	---help---
+	  This driver supports IP1000 gigabit Ethernet cards.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ipg.  This is recommended.
+
 source "drivers/net/ixp2000/Kconfig"
 
 config MYRI_SBUS
@@ -2468,9 +2477,6 @@ config IXGBE
 
 	  <http://support.intel.com>
 
-	  More specific information on configuring the driver is in
-	  <file:Documentation/networking/ixgbe.txt>.
-
 	  To compile this driver as a module, choose M here. The module
 	  will be called ixgbe.
 
@@ -2591,6 +2597,15 @@ config TEHUTI
 	help
 	  Tehuti Networks 10G Ethernet NIC
 
+config BNX2X
+	tristate "Broadcom NetXtremeII 10Gb support"
+	depends on PCI
+	help
+	  This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
+	  To compile this driver as a module, choose M here: the module
+	  will be called bnx2x.  This is recommended.
+
+
 endif # NETDEV_10000
 
 source "drivers/net/tokenring/Kconfig"
@@ -3021,23 +3036,6 @@ config NET_FC
 	  adaptor below. You also should have said Y to "SCSI support" and
 	  "SCSI generic support".
 
-config SHAPER
-	tristate "Traffic Shaper (OBSOLETE)"
-	depends on EXPERIMENTAL
-	---help---
-	  The traffic shaper is a virtual network device that allows you to
-	  limit the rate of outgoing data flow over some other network device.
-	  The traffic that you want to slow down can then be routed through
-	  these virtual devices. See
-	  <file:Documentation/networking/shaper.txt> for more information.
-
-	  An alternative to this traffic shaper are traffic schedulers which
-	  you'll get if you say Y to "QoS and/or fair queuing" in
-	  "Networking options".
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called shaper.  If unsure, say N.
-
 config NETCONSOLE
 	tristate "Network console logging support (EXPERIMENTAL)"
 	depends on EXPERIMENTAL