X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fnet%2Fbnx2x_init.h;h=130927cfc75b63c79f986280029ddc4596f81c46;hb=fd5070370c74c32b7a98090eabb46c53baf41733;hp=4c7750789b62309ca7d410c51122dbafa395d394;hpb=c4c0c56a7a85ed5725786219e4fbca7e840b1531;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/net/bnx2x_init.h b/drivers/net/bnx2x_init.h
index 4c7750789b6..130927cfc75 100644
--- a/drivers/net/bnx2x_init.h
+++ b/drivers/net/bnx2x_init.h
@@ -72,26 +72,26 @@
 
 
 struct raw_op {
-	u32 op		:8;
-	u32 offset	:24;
+	u32 op:8;
+	u32 offset:24;
 	u32 raw_data;
 };
 
 struct op_read {
-	u32 op		:8;
-	u32 offset	:24;
+	u32 op:8;
+	u32 offset:24;
 	u32 pad;
 };
 
 struct op_write {
-	u32 op		:8;
-	u32 offset	:24;
+	u32 op:8;
+	u32 offset:24;
 	u32 val;
 };
 
 struct op_string_write {
-	u32 op		:8;
-	u32 offset	:24;
+	u32 op:8;
+	u32 offset:24;
 #ifdef __LITTLE_ENDIAN
 	u16 data_off;
 	u16 data_len;
@@ -102,8 +102,8 @@ struct op_string_write {
 };
 
 struct op_zero {
-	u32 op		:8;
-	u32 offset	:24;
+	u32 op:8;
+	u32 offset:24;
 	u32 len;
 };
 
@@ -208,7 +208,7 @@ static void bnx2x_init_wr_64(struct bnx2x *bp, u32 addr, const u32 *data,
 /*********************************************************
    There are different blobs for each PRAM section.
    In addition, each blob write operation is divided into a few operations
-   in order to decrease the amount of phys. contigious buffer needed.
+   in order to decrease the amount of phys. contiguous buffer needed.
    Thus, when we select a blob the address may be with some offset
    from the beginning of PRAM section.
    The same holds for the INT_TABLE sections.
@@ -336,7 +336,7 @@ static void bnx2x_init_block(struct bnx2x *bp, u32 op_start, u32 op_end)
 		len = op->str_wr.data_len;
 		data = data_base + op->str_wr.data_off;
 
-		/* carefull! it must be in order */
+		/* careful! it must be in order */
 		if (unlikely(op_type > OP_WB)) {
 
 			/* If E1 only */
@@ -740,7 +740,7 @@ static u8 calc_crc8(u32 data, u8 crc)
 	return crc_res;
 }
 
-/* regiesers addresses are not in order
+/* registers addresses are not in order
    so these arrays help simplify the code */
 static const int cm_start[E1H_FUNC_MAX][9] = {
 	{MISC_FUNC0_START, TCM_FUNC0_START, UCM_FUNC0_START, CCM_FUNC0_START,