X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fserial%2F8250_hp300.c;h=0e1410f2c03394362f25a07b6ce27981dff38ab2;hb=1b821bfb034c5db5af62b463e3001243905179ba;hp=53e81a44c1a3917fece986bef143e38401ff6f7e;hpb=2e1ca21d46aaef95101723fa402f39d3a95aba59;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/serial/8250_hp300.c b/drivers/serial/8250_hp300.c
index 53e81a44c1a..0e1410f2c03 100644
--- a/drivers/serial/8250_hp300.c
+++ b/drivers/serial/8250_hp300.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/serial.h>
 #include <linux/serial_core.h>
+#include <linux/serial_8250.h>
 #include <linux/delay.h>
 #include <linux/dio.h>
 #include <linux/console.h>
@@ -35,7 +36,7 @@ static struct hp300_port *hp300_ports;
 #ifdef CONFIG_HPDCA
 
 static int __devinit hpdca_init_one(struct dio_dev *d,
-                                const struct dio_device_id *ent);
+					const struct dio_device_id *ent);
 static void __devexit hpdca_remove_one(struct dio_dev *d);
 
 static struct dio_device_id hpdca_dio_tbl[] = {
@@ -84,7 +85,7 @@ extern int hp300_uart_scode;
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 /*
- * Parse the bootinfo to find descriptions for headless console and 
+ * Parse the bootinfo to find descriptions for headless console and
  * debug serial ports and register them with the 8250 driver.
  * This function should be called before serial_console_init() is called
  * to make sure the serial console will be available for use. IA-64 kernel
@@ -125,13 +126,11 @@ int __init hp300_setup_serial_console(void)
 		printk(KERN_WARNING "Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
 		return 0;
 #endif
-	}
-	else {
+	} else {
 #ifdef CONFIG_HPDCA
 		unsigned long pa = dio_scodetophysaddr(scode);
-		if (!pa) {
+		if (!pa)
 			return 0;
-		}
 
 		printk(KERN_INFO "Serial console is HP DCA at select code %d\n", scode);
 
@@ -144,26 +143,23 @@ int __init hp300_setup_serial_console(void)
 		/* Enable board-interrupts */
 		out_8(pa + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
 
-		if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80) {
+		if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80)
 			add_preferred_console("ttyS", port.line, "9600n8");
-		}
 #else
 		printk(KERN_WARNING "Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
 		return 0;
 #endif
 	}
 
-	if (early_serial_setup(&port) < 0) {
+	if (early_serial_setup(&port) < 0)
 		printk(KERN_WARNING "hp300_setup_serial_console(): early_serial_setup() failed.\n");
-	}
-
 	return 0;
 }
 #endif /* CONFIG_SERIAL_8250_CONSOLE */
 
 #ifdef CONFIG_HPDCA
 static int __devinit hpdca_init_one(struct dio_dev *d,
-                                const struct dio_device_id *ent)
+				const struct dio_device_id *ent)
 {
 	struct uart_port port;
 	int line;
@@ -209,7 +205,7 @@ static int __devinit hpdca_init_one(struct dio_dev *d,
 
 static int __init hp300_8250_init(void)
 {
-	static int called = 0;
+	static int called;
 #ifdef CONFIG_HPAPCI
 	int line;
 	unsigned long base;
@@ -238,13 +234,12 @@ static int __init hp300_8250_init(void)
 	 * Port 1 is either the console or the DCA.
 	 */
 	for (i = 1; i < 4; i++) {
-		/* Port 1 is the console on a 425e, on other machines it's mapped to
-		 * DCA.
+		/* Port 1 is the console on a 425e, on other machines it's
+		 * mapped to DCA.
 		 */
 #ifdef CONFIG_SERIAL_8250_CONSOLE
-		if (i == 1) {
+		if (i == 1)
 			continue;
-		}
 #endif
 
 		/* Create new serial device */
@@ -258,7 +253,8 @@ static int __init hp300_8250_init(void)
 
 		/* Memory mapped I/O */
 		uport.iotype = UPIO_MEM;
-		uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
+		uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
+			      | UPF_BOOT_AUTOCONF;
 		/* XXX - no interrupt support yet */
 		uport.irq = 0;
 		uport.uartclk = HPAPCI_BAUD_BASE * 16;
@@ -269,8 +265,8 @@ static int __init hp300_8250_init(void)
 		line = serial8250_register_port(&uport);
 
 		if (line < 0) {
-			printk(KERN_NOTICE "8250_hp300: register_serial() APCI %d"
-			       " irq %d failed\n", i, uport.irq);
+			printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
+			       " %d irq %d failed\n", i, uport.irq);
 			kfree(port);
 			continue;
 		}