X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fusb%2Fserial%2Fkeyspan.h;h=b52fb657a24410887e7925c874c36b48c3c3c771;hb=0031a06e2f07ab0d1bc98c31dbb6801f95f4bf01;hp=74ce8bca3e668422af542a6b709b3e762bc42418;hpb=2eccd6f65a0d4844318b1e30755cafd063833908;p=linux-2.6-omap-h63xx.git

diff --git a/drivers/usb/serial/keyspan.h b/drivers/usb/serial/keyspan.h
index 74ce8bca3e6..b52fb657a24 100644
--- a/drivers/usb/serial/keyspan.h
+++ b/drivers/usb/serial/keyspan.h
@@ -103,90 +103,6 @@ static int  keyspan_usa67_send_setup	(struct usb_serial *serial,
 					 struct usb_serial_port *port,
 					 int reset_port);
 
-/* Struct used for firmware - increased size of data section
-   to allow Keyspan's 'C' firmware struct to be used unmodified */
-struct ezusb_hex_record {
-	__u16 address;
-	__u8 data_size;
-	__u8 data[64];
-};
-
-/* Conditionally include firmware images, if they aren't
-   included create a null pointer instead.  Current 
-   firmware images aren't optimised to remove duplicate
-   addresses in the image itself. */
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA28
-	#include "keyspan_usa28_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa28_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA28X
-	#include "keyspan_usa28x_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa28x_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA28XA
-	#include "keyspan_usa28xa_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa28xa_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA28XB
-	#include "keyspan_usa28xb_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa28xb_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA19
-	#include "keyspan_usa19_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa19_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA19QI
-	#include "keyspan_usa19qi_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa19qi_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_MPR
-        #include "keyspan_mpr_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_mpr_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA19QW
-	#include "keyspan_usa19qw_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa19qw_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA18X
-	#include "keyspan_usa18x_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa18x_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA19W
-	#include "keyspan_usa19w_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa19w_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA49W
-	#include "keyspan_usa49w_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa49w_firmware = NULL;
-#endif
-
-#ifdef CONFIG_USB_SERIAL_KEYSPAN_USA49WLC
-        #include "keyspan_usa49wlc_fw.h"
-#else
-	static const struct ezusb_hex_record *keyspan_usa49wlc_firmware = NULL;
-#endif
-
 /* Values used for baud rate calculation - device specific */
 #define	KEYSPAN_INVALID_BAUD_RATE		(-1)
 #define	KEYSPAN_BAUD_RATE_OK			(0)
@@ -636,10 +552,6 @@ static struct usb_serial_driver keyspan_pre_device = {
 	},
 	.description		= "Keyspan - (without firmware)",
 	.id_table		= keyspan_pre_ids,
-	.num_interrupt_in	= NUM_DONT_CARE,
-	.num_interrupt_out	= NUM_DONT_CARE,
-	.num_bulk_in		= NUM_DONT_CARE,
-	.num_bulk_out		= NUM_DONT_CARE,
 	.num_ports		= 1,
 	.attach			= keyspan_fake_startup,
 };
@@ -651,10 +563,6 @@ static struct usb_serial_driver keyspan_1port_device = {
 	},
 	.description		= "Keyspan 1 port adapter",
 	.id_table		= keyspan_1port_ids,
-	.num_interrupt_in	= NUM_DONT_CARE,
-	.num_interrupt_out	= NUM_DONT_CARE,
-	.num_bulk_in		= NUM_DONT_CARE,
-	.num_bulk_out		= NUM_DONT_CARE,
 	.num_ports		= 1,
 	.open			= keyspan_open,
 	.close			= keyspan_close,
@@ -679,10 +587,6 @@ static struct usb_serial_driver keyspan_2port_device = {
 	},
 	.description		= "Keyspan 2 port adapter",
 	.id_table		= keyspan_2port_ids,
-	.num_interrupt_in	= NUM_DONT_CARE,
-	.num_interrupt_out	= NUM_DONT_CARE,
-	.num_bulk_in		= NUM_DONT_CARE,
-	.num_bulk_out		= NUM_DONT_CARE,
 	.num_ports		= 2,
 	.open			= keyspan_open,
 	.close			= keyspan_close,
@@ -707,10 +611,6 @@ static struct usb_serial_driver keyspan_4port_device = {
 	},
 	.description		= "Keyspan 4 port adapter",
 	.id_table		= keyspan_4port_ids,
-	.num_interrupt_in	= NUM_DONT_CARE,
-	.num_interrupt_out	= NUM_DONT_CARE,
-	.num_bulk_in		= NUM_DONT_CARE,
-	.num_bulk_out		= NUM_DONT_CARE,
 	.num_ports		= 4,
 	.open			= keyspan_open,
 	.close			= keyspan_close,