X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=include%2Flinux%2Fipmi.h;h=7a9db390c56a491e3221ed8154ac76ed89295c8f;hb=8d00647f2cf0780497274a4b0ab0e66509579459;hp=796ca009fd468a8716cd8d6b31570bcc83ca4faf;hpb=5a3e3b2230980cf2ce6e5e56b816dde19b993939;p=linux-2.6-omap-h63xx.git

diff --git a/include/linux/ipmi.h b/include/linux/ipmi.h
index 796ca009fd4..7a9db390c56 100644
--- a/include/linux/ipmi.h
+++ b/include/linux/ipmi.h
@@ -208,6 +208,15 @@ struct kernel_ipmi_msg
    code as the first byte of the incoming data, unlike a response. */
 
 
+/*
+ * Modes for ipmi_set_maint_mode() and the userland IOCTL.  The AUTO
+ * setting is the default and means it will be set on certain
+ * commands.  Hard setting it on and off will override automatic
+ * operation.
+ */
+#define IPMI_MAINTENANCE_MODE_AUTO	0
+#define IPMI_MAINTENANCE_MODE_OFF	1
+#define IPMI_MAINTENANCE_MODE_ON	2
 
 #ifdef __KERNEL__
 
@@ -373,6 +382,35 @@ int ipmi_unregister_for_cmd(ipmi_user_t   user,
 			    unsigned char cmd,
 			    unsigned int  chans);
 
+/*
+ * Go into a mode where the driver will not autonomously attempt to do
+ * things with the interface.  It will still respond to attentions and
+ * interrupts, and it will expect that commands will complete.  It
+ * will not automatcially check for flags, events, or things of that
+ * nature.
+ *
+ * This is primarily used for firmware upgrades.  The idea is that
+ * when you go into firmware upgrade mode, you do this operation
+ * and the driver will not attempt to do anything but what you tell
+ * it or what the BMC asks for.
+ *
+ * Note that if you send a command that resets the BMC, the driver
+ * will still expect a response from that command.  So the BMC should
+ * reset itself *after* the response is sent.  Resetting before the
+ * response is just silly.
+ *
+ * If in auto maintenance mode, the driver will automatically go into
+ * maintenance mode for 30 seconds if it sees a cold reset, a warm
+ * reset, or a firmware NetFN.  This means that code that uses only
+ * firmware NetFN commands to do upgrades will work automatically
+ * without change, assuming it sends a message every 30 seconds or
+ * less.
+ *
+ * See the IPMI_MAINTENANCE_MODE_xxx defines for what the mode means.
+ */
+int ipmi_get_maintenance_mode(ipmi_user_t user);
+int ipmi_set_maintenance_mode(ipmi_user_t user, int mode);
+
 /*
  * Allow run-to-completion mode to be set for the interface of
  * a specific user.
@@ -656,4 +694,11 @@ struct ipmi_timing_parms
 #define IPMICTL_GET_TIMING_PARMS_CMD	_IOR(IPMI_IOC_MAGIC, 23, \
 					     struct ipmi_timing_parms)
 
+/*
+ * Set the maintenance mode.  See ipmi_set_maintenance_mode() above
+ * for a description of what this does.
+ */
+#define IPMICTL_GET_MAINTENANCE_MODE_CMD	_IOR(IPMI_IOC_MAGIC, 30, int)
+#define IPMICTL_SET_MAINTENANCE_MODE_CMD	_IOW(IPMI_IOC_MAGIC, 31, int)
+
 #endif /* __LINUX_IPMI_H */