X-Git-Url: http://pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=include%2Fnet%2Fmac80211.h;h=ff137fd7714f2909aca78a352990366cb02005b9;hb=6951df34d50330f1b117fd8371d7f7df39f43f6a;hp=b52721008be81dd34e3b6379e8729c5abf439b0a;hpb=1e24b15b267293567a8d752721c7ae63f281325a;p=linux-2.6-omap-h63xx.git

diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index b52721008be..ff137fd7714 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -177,9 +177,10 @@ enum ieee80211_bss_change {
  * @aid: association ID number, valid only when @assoc is true
  * @use_cts_prot: use CTS protection
  * @use_short_preamble: use 802.11b short preamble
+ * @dtim_period: num of beacons before the next DTIM, for PSM
  * @timestamp: beacon timestamp
  * @beacon_int: beacon interval
- * @assoc_capability: capabbilities taken from assoc resp
+ * @assoc_capability: capabilities taken from assoc resp
  * @assoc_ht: association in HT mode
  * @ht_conf: ht capabilities
  * @ht_bss_conf: ht extended capabilities
@@ -191,6 +192,7 @@ struct ieee80211_bss_conf {
 	/* erp related data */
 	bool use_cts_prot;
 	bool use_short_preamble;
+	u8 dtim_period;
 	u16 beacon_int;
 	u16 assoc_capability;
 	u64 timestamp;
@@ -430,6 +432,7 @@ enum ieee80211_conf_flags {
  * @radio_enabled: when zero, driver is required to switch off the radio.
  *	TODO make a flag
  * @beacon_int: beacon interval (TODO make interface config)
+ * @listen_interval: listen interval in units of beacon interval
  * @flags: configuration flags defined above
  * @power_level: requested transmit power (in dBm)
  * @max_antenna_gain: maximum antenna gain (in dBi)
@@ -444,6 +447,7 @@ struct ieee80211_conf {
 	int radio_enabled;
 
 	int beacon_int;
+	u16 listen_interval;
 	u32 flags;
 	int power_level;
 	int max_antenna_gain;
@@ -704,10 +708,7 @@ enum ieee80211_tkip_key_type {
  *	rely on the host system for such buffering. This option is used
  *	to configure the IEEE 802.11 upper layer to buffer broadcast and
  *	multicast frames when there are power saving stations so that
- *	the driver can fetch them with ieee80211_get_buffered_bc(). Note
- *	that not setting this flag works properly only when the
- *	%IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
- *	otherwise the stack will not know when the DTIM beacon was sent.
+ *	the driver can fetch them with ieee80211_get_buffered_bc().
  *
  * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
  *	Hardware is not capable of short slot operation on the 2.4 GHz band.
@@ -785,6 +786,9 @@ enum ieee80211_hw_flags {
  * @max_signal: Maximum value for signal (rssi) in RX information, used
  *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
  *
+ * @max_listen_interval: max listen interval in units of beacon interval
+ *     that HW supports
+ *
  * @queues: number of available hardware transmit queues for
  *	data packets. WMM/QoS requires at least four, these
  *	queues need to have configurable access parameters.
@@ -812,7 +816,9 @@ struct ieee80211_hw {
 	unsigned int extra_tx_headroom;
 	int channel_change_time;
 	int vif_data_size;
-	u16 queues, ampdu_queues;
+	u16 queues;
+	u16 ampdu_queues;
+	u16 max_listen_interval;
 	s8 max_signal;
 };
 
@@ -1090,10 +1096,8 @@ enum ieee80211_ampdu_mlme_action {
  *	See the section "Frame filtering" for more information.
  *	This callback must be implemented and atomic.
  *
- * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon
- *	generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set)
- *	mac80211 calls this function when a TIM bit must be set or cleared
- *	for a given AID. Must be atomic.
+ * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
+ * 	must be set or cleared for a given AID. Must be atomic.
  *
  * @set_key: See the section "Hardware crypto acceleration"
  *	This callback can sleep, and is only called between add_interface