return omap_get_gpio_datain(H3_NAND_RB_GPIO_PIN);
}
+#if defined(CONFIG_VIDEO_OV9640) || defined(CONFIG_VIDEO_OV9640_MODULE)
+/*
+ * Common OV9640 register initialization for all image sizes, pixel formats,
+ * and frame rates
+ */
+const static struct ov9640_reg ov9640_common[] = {
+
+ { 0x12, 0x80 }, { 0x11, 0x80 }, { 0x13, 0x88 }, /* COM7, CLKRC, COM8 */
+ { 0x01, 0x58 }, { 0x02, 0x24 }, { 0x04, 0x00 }, /* BLUE, RED, COM1 */
+ { 0x0E, 0x81 }, { 0x0F, 0x4F }, { 0x14, 0xcA }, /* COM5, COM6, COM9 */
+ { 0x16, 0x02 }, { 0x1B, 0x01 }, { 0x24, 0x70 }, /* ?, PSHFT, AEW */
+ { 0x25, 0x68 }, { 0x26, 0xD3 }, { 0x27, 0x90 }, /* AEB, VPT, BBIAS */
+ { 0x2A, 0x00 }, { 0x2B, 0x00 }, { 0x32, 0x24 }, /* EXHCH, EXHCL, HREF */
+ { 0x33, 0x02 }, { 0x37, 0x02 }, { 0x38, 0x13 }, /* CHLF, ADC, ACOM */
+ { 0x39, 0xF0 }, { 0x3A, 0x00 }, { 0x3B, 0x01 }, /* OFON, TSLB, COM11 */
+ { 0x3D, 0x90 }, { 0x3E, 0x02 }, { 0x3F, 0xF2 }, /* COM13, COM14, EDGE */
+ { 0x41, 0x02 }, { 0x42, 0xC8 }, /* COM16, COM17 */
+ { 0x43, 0xF0 }, { 0x44, 0x10 }, { 0x45, 0x6C }, /* ?, ?, ? */
+ { 0x46, 0x6C }, { 0x47, 0x44 }, { 0x48, 0x44 }, /* ?, ?, ? */
+ { 0x49, 0x03 }, { 0x59, 0x49 }, { 0x5A, 0x94 }, /* ?, ?, ? */
+ { 0x5B, 0x46 }, { 0x5C, 0x84 }, { 0x5D, 0x5C }, /* ?, ?, ? */
+ { 0x5E, 0x08 }, { 0x5F, 0x00 }, { 0x60, 0x14 }, /* ?, ?, ? */
+ { 0x61, 0xCE }, /* ? */
+ { 0x62, 0x70 }, { 0x63, 0x00 }, { 0x64, 0x04 }, /* LCC1, LCC2, LCC3 */
+ { 0x65, 0x00 }, { 0x66, 0x00 }, /* LCC4, LCC5 */
+ { 0x69, 0x00 }, { 0x6A, 0x3E }, { 0x6B, 0x3F }, /* HV, MBD, DBLV */
+ { 0x6C, 0x40 }, { 0x6D, 0x30 }, { 0x6E, 0x4B }, /* GSP1, GSP2, GSP3 */
+ { 0x6F, 0x60 }, { 0x70, 0x70 }, { 0x71, 0x70 }, /* GSP4, GSP5, GSP6 */
+ { 0x72, 0x70 }, { 0x73, 0x70 }, { 0x74, 0x60 }, /* GSP7, GSP8, GSP9 */
+ { 0x75, 0x60 }, { 0x76, 0x50 }, { 0x77, 0x48 }, /* GSP10,GSP11,GSP12 */
+ { 0x78, 0x3A }, { 0x79, 0x2E }, { 0x7A, 0x28 }, /* GSP13,GSP14,GSP15 */
+ { 0x7B, 0x22 }, { 0x7C, 0x04 }, { 0x7D, 0x07 }, /* GSP16,GST1, GST2 */
+ { 0x7E, 0x10 }, { 0x7F, 0x28 }, { 0x80, 0x36 }, /* GST3, GST4, GST5 */
+ { 0x81, 0x44 }, { 0x82, 0x52 }, { 0x83, 0x60 }, /* GST6, GST7, GST8 */
+ { 0x84, 0x6C }, { 0x85, 0x78 }, { 0x86, 0x8C }, /* GST9, GST10,GST11 */
+ { 0x87, 0x9E }, { 0x88, 0xBB }, { 0x89, 0xD2 }, /* GST12,GST13,GST14 */
+ { 0x8A, 0xE6 }, { 0x13, 0xaF }, { 0x15, 0x02 }, /* GST15, COM8 */
+ { 0x22, 0x8a }, /* GROS */
+ { OV9640_REG_TERM, OV9640_VAL_TERM }
+};
+
+static int ov9640_sensor_power_set(int power)
+{
+ unsigned char expa;
+ int err;
+
+ /* read current state of GPIO EXPA outputs */
+ err = read_gpio_expa(&expa, 0x27);
+ if (err) {
+ printk(KERN_ERR "Error reading GPIO EXPA\n");
+ return err;
+ }
+ /* Clear GPIO EXPA P3 (CAMERA_MODULE_EN) to power-up/down sensor */
+ if (power)
+ expa |= 0x08;
+ else
+ expa &= ~0x08;
+
+ err = write_gpio_expa(expa, 0x27);
+ if (err) {
+ printk(KERN_ERR "Error writing to GPIO EXPA\n");
+ return err;
+ }
+
+ return err;
+}
+
+static struct v4l2_ifparm ifparm = {
+ .if_type = V4L2_IF_TYPE_BT656,
+ .u = {
+ .bt656 = {
+ .frame_start_on_rising_vs = 1,
+ .nobt_vs_inv = 1,
+ .mode = V4L2_IF_TYPE_BT656_MODE_NOBT_8BIT,
+ .clock_min = OV9640_XCLK_MIN,
+ .clock_max = OV9640_XCLK_MAX,
+ },
+ },
+};
+
+static int ov9640_ifparm(struct v4l2_ifparm *p)
+{
+ *p = ifparm;
+
+ return 0;
+}
+
+static struct ov9640_platform_data h3_ov9640_platform_data = {
+ .power_set = ov9640_sensor_power_set,
+ .default_regs = ov9640_common,
+ .ifparm = ov9640_ifparm,
+};
+#endif
+
+static struct i2c_board_info __initdata h3_i2c_board_info[] = {
++ {
++ I2C_BOARD_INFO("tps65013", 0x48),
++ /* .irq = OMAP_GPIO_IRQ(??), */
++ },
+#if defined(CONFIG_VIDEO_OV9640) || defined(CONFIG_VIDEO_OV9640_MODULE)
+ {
+ I2C_BOARD_INFO("ov9640", 0x30),
+ .platform_data = &h3_ov9640_platform_data,
+ },
+#endif
+ {
+ I2C_BOARD_INFO("isp1301_omap", 0x2d),
+ .type = "isp1301_omap",
+ .irq = OMAP_GPIO_IRQ(14),
+ },
+};
+
static void __init h3_init(void)
{
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
To compile this driver as a module, choose M here: the
module will be called touchwin.
- config TOUCHSCREEN_UCB1400
- tristate "Philips UCB1400 touchscreen"
- select AC97_BUS
- help
- This enables support for the Philips UCB1400 touchscreen interface.
- The UCB1400 is an AC97 audio codec. The touchscreen interface
- will be initialized only after the ALSA subsystem has been
- brought up and the UCB1400 detected. You therefore have to
- configure ALSA support as well (either built-in or modular,
- independently of whether this driver is itself built-in or
- modular) for this driver to work.
-
- To compile this driver as a module, choose M here: the
- module will be called ucb1400_ts.
-
+config TOUCHSCREEN_TSC2005
+ tristate "TSC2005 touchscreen support"
+ help
+ Say Y here for if you are using the touchscreen features of TSC2301.
+
+config TOUCHSCREEN_TSC2102
+ tristate "TSC 2102 based touchscreens"
+ depends on SPI_MASTER
+ select SPI_TSC2102
+ help
+ Say Y here if you have a touchscreen interface using the
+ TI TSC 2102 controller, and your board-specific initialization
+ code includes that in its table of SPI devices. Also make
+ sure the proper SPI controller is selected.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc2102_ts.
+
+config TOUCHSCREEN_TSC210X
+ tristate "TI TSC210x based touchscreens"
+ depends on SPI_MASTER
+ select SPI_TSC210X
+ help
+ Say Y here if you have a touchscreen interface using a
+ TI TSC210x controller, and your board-specific initialisation
+ code includes that in its table of SPI devices.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc210x_ts.
+
+config TOUCHSCREEN_TSC2301
+ tristate "TSC2301 touchscreen support"
+ depends on SPI_TSC2301
+ help
+ Say Y here for if you are using the touchscreen features of TSC2301.
+
+ config TOUCHSCREEN_UCB1400
+ tristate "Philips UCB1400 touchscreen"
+ select AC97_BUS
+ help
+ This enables support for the Philips UCB1400 touchscreen interface.
+ The UCB1400 is an AC97 audio codec. The touchscreen interface
+ will be initialized only after the ALSA subsystem has been
+ brought up and the UCB1400 detected. You therefore have to
+ configure ALSA support as well (either built-in or modular,
+ independently of whether this driver is itself built-in or
+ modular) for this driver to work.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ucb1400_ts.
+
+ config TOUCHSCREEN_WM97XX
+ tristate "Support for WM97xx AC97 touchscreen controllers"
+ depends on AC97_BUS
+ help
+ Say Y here if you have a Wolfson Microelectronics WM97xx
+ touchscreen connected to your system. Note that this option
+ only enables core driver, you will also need to select
+ support for appropriate chip below.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wm97xx-ts.
+
+ config TOUCHSCREEN_WM9705
+ bool "WM9705 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9705
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+ config TOUCHSCREEN_WM9712
+ bool "WM9712 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9712
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+ config TOUCHSCREEN_WM9713
+ bool "WM9713 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
+ controller connected to your system.
+
+ If unsure, say N.
+
+ config TOUCHSCREEN_WM97XX_MAINSTONE
+ tristate "WM97xx Mainstone accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && ARCH_PXA
+ help
+ Say Y here for support for streaming mode with WM97xx touchscreens
+ on Mainstone systems.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mainstone-wm97xx.
+
config TOUCHSCREEN_USB_COMPOSITE
tristate "USB Touchscreen Driver"
depends on USB_ARCH_HAS_HCD
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
obj-$(CONFIG_TOUCHSCREEN_UCB1400) += ucb1400_ts.o
+obj-$(CONFIG_TOUCHSCREEN_TSC2005) += tsc2005.o
+obj-$(CONFIG_TOUCHSCREEN_TSC2102) += tsc2102_ts.o
+obj-$(CONFIG_TOUCHSCREEN_OMAP) += omap/
+obj-$(CONFIG_TOUCHSCREEN_TSC210X) += tsc210x_ts.o
+obj-$(CONFIG_TOUCHSCREEN_TSC2301) += tsc2301_ts.o
+ obj-$(CONFIG_TOUCHSCREEN_WM97XX) += wm97xx-ts.o
+ wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9705) += wm9705.o
+ wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9712) += wm9712.o
+ wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9713) += wm9713.o
+ obj-$(CONFIG_TOUCHSCREEN_WM97XX_MAINSTONE) += mainstone-wm97xx.o
source "drivers/media/video/ivtv/Kconfig"
+source drivers/media/video/omap/Kconfig
+
+ source "drivers/media/video/cx18/Kconfig"
+
config VIDEO_M32R_AR
tristate "AR devices"
depends on M32R && VIDEO_V4L1
If unsure, say N.
- If you have an Eee PC laptop, say Y or M here.
+ config EEEPC_LAPTOP
+ tristate "Eee PC Hotkey Driver (EXPERIMENTAL)"
+ depends on X86
+ depends on ACPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ depends on HWMON
+ depends on EXPERIMENTAL
++
+ ---help---
+ This driver supports the Fn-Fx keys on Eee PC laptops.
+ It also adds the ability to switch camera/wlan on/off.
+
- bool "Serial Trace Interface support"
- depends on ARCH_OMAP16XX || ARCH_OMAP24XX || ARCH_OMAP34XX
- default n
- help
- Serial Trace Interface. The protocols suported for OMAP1/2/3 are
- STI/CSTI/XTIv2 correspondingly.
+config OMAP_STI
++ bool "Serial Trace Interface support"
++ depends on ARCH_OMAP16XX || ARCH_OMAP24XX || ARCH_OMAP34XX
++ default n
++ help
++ Serial Trace Interface. The protocols suported for OMAP1/2/3 are
++ STI/CSTI/XTIv2 correspondingly.
+
+config OMAP_STI_CONSOLE
+ bool "STI console support"
+ depends on OMAP_STI
+ help
+ This enables a console driver by way of STI/XTI.
config ENCLOSURE_SERVICES
tristate "Enclosure Services"
obj-$(CONFIG_IBM_ASM) += ibmasm/
obj-$(CONFIG_HDPU_FEATURES) += hdpuftrs/
+obj-$(CONFIG_OMAP_STI) += sti/
obj-$(CONFIG_MSI_LAPTOP) += msi-laptop.o
obj-$(CONFIG_ACER_WMI) += acer-wmi.o
- obj-$(CONFIG_ASUS_LAPTOP) += asus-laptop.o
+ obj-$(CONFIG_ASUS_LAPTOP) += asus-laptop.o
+ obj-$(CONFIG_EEEPC_LAPTOP) += eeepc-laptop.o
obj-$(CONFIG_ATMEL_PWM) += atmel_pwm.o
obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o
obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o
return err;
}
- static int __devexit omapflash_remove(struct platform_device *pdev)
+ static int __exit omapflash_remove(struct platform_device *pdev)
{
struct omapflash_info *info = platform_get_drvdata(pdev);
+ struct flash_platform_data *pdata = pdev->dev.platform_data;
platform_set_drvdata(pdev, NULL);
To compile this driver as a module, choose M here: the
module will be called ehci-hcd.
+choice
+ prompt "PHY/TLL mode"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ Choose PHY or TLL mode of operation
+
+config OMAP_EHCI_PHY_MODE
+ bool "PHY mode: ISP1504 on Port1/2 (NEW 3430ES2.0)"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ EHCI PHY mode. Port1 and Port2 are connected to ISP1504 transcievers
+
+config OMAP_EHCI_TLL_MODE
+ bool "TLL mode: (EXPERIMENTAL)"
+ depends on USB_EHCI_HCD && EXPERIMENTAL && ARCH_OMAP34XX
+ ---help---
+ OMAP EHCI controller has TLL mode of operation for all 3 ports.
+ Use this mode when no transciever is present
+endchoice
config USB_EHCI_ROOT_HUB_TT
- bool "Root Hub Transaction Translators (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
+ bool "Root Hub Transaction Translators"
+ depends on USB_EHCI_HCD
---help---
Some EHCI chips have vendor-specific extensions to integrate
transaction translators, so that no OHCI or UHCI companion
return ret;
}
- #else
- #warning "don't include kernel headers in userspace"
- #endif /* __KERNEL__ */
+/**
+ * kfifo_get_to_user - gets some data from the FIFO
+ * @fifo: the fifo to be used.
+ * @buffer: where the data must be copied. user buffer
+ * @len: the size of the destination buffer.
+ *
+ * This function copies at most @len bytes from the FIFO into the
+ * user @buffer and returns the number of copied bytes.
+ */
+static inline unsigned int kfifo_get_to_user(struct kfifo *fifo,
+ unsigned char __user *buffer,
+ unsigned int len)
+{
+ unsigned long flags;
+ unsigned int ret;
+
+ spin_lock_irqsave(fifo->lock, flags);
+
+ ret = __kfifo_get_to_user(fifo, buffer, len);
+
+ /*
+ * optimization: if the FIFO is empty, set the indices to 0
+ * so we don't wrap the next time
+ */
+ if (fifo->in == fifo->out)
+ fifo->in = fifo->out = 0;
+
+ spin_unlock_irqrestore(fifo->lock, flags);
+
+ return ret;
+}
+
#endif
obj-$(CONFIG_SECURITY_SMACK) += commoncap.o smack/built-in.o
obj-$(CONFIG_SECURITY_CAPABILITIES) += commoncap.o capability.o
obj-$(CONFIG_SECURITY_ROOTPLUG) += commoncap.o root_plug.o
+obj-$(CONFIG_SECURITY_LOWMEM) += commoncap.o lowmem.o
+ obj-$(CONFIG_CGROUP_DEVICE) += device_cgroup.o
projects / linux-2.6-omap-h63xx.git / commitdiff