===================================
The regulator machine driver interface is intended for board/machine specific
-initialisation code to configure the regulator subsystem. Typical things that
-machine drivers would do are :-
+initialisation code to configure the regulator subsystem.
- 1. Regulator -> Device mapping.
- 2. Regulator supply configuration.
- 3. Power Domain constraint setting.
-
-
-
-1. Regulator -> device mapping
-==============================
Consider the following machine :-
Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
The drivers for consumers A & B must be mapped to the correct regulator in
order to control their power supply. This mapping can be achieved in machine
-initialisation code by calling :-
+initialisation code by creating a struct regulator_consumer_supply for
+each regulator.
+
+struct regulator_consumer_supply {
+ struct device *dev; /* consumer */
+ const char *supply; /* consumer supply - e.g. "vcc" */
+};
-int regulator_set_device_supply(const char *regulator, struct device *dev,
- const char *supply);
+e.g. for the machine above
-and is shown with the following code :-
+static struct regulator_consumer_supply regulator1_consumers[] = {
+{
+ .dev = &platform_consumerB_device.dev,
+ .supply = "Vcc",
+},};
-regulator_set_device_supply("Regulator-1", devB, "Vcc");
-regulator_set_device_supply("Regulator-2", devA, "Vcc");
+static struct regulator_consumer_supply regulator2_consumers[] = {
+{
+ .dev = &platform_consumerA_device.dev,
+ .supply = "Vcc",
+},};
This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2
to the 'Vcc' supply for Consumer A.
-
-2. Regulator supply configuration.
-==================================
-Consider the following machine (again) :-
-
- Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
- |
- +-> [Consumer B @ 3.3V]
+Constraints can now be registered by defining a struct regulator_init_data
+for each regulator power domain. This structure also maps the consumers
+to their supply regulator :-
+
+static struct regulator_init_data regulator1_data = {
+ .constraints = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(regulator1_consumers),
+ .consumer_supplies = regulator1_consumers,
+};
Regulator-1 supplies power to Regulator-2. This relationship must be registered
with the core so that Regulator-1 is also enabled when Consumer A enables it's
-supply (Regulator-2).
-
-This relationship can be register with the core via :-
-
-int regulator_set_supply(const char *regulator, const char *regulator_supply);
-
-In this example we would use the following code :-
-
-regulator_set_supply("Regulator-2", "Regulator-1");
-
-Relationships can be queried by calling :-
-
-const char *regulator_get_supply(const char *regulator);
-
-
-3. Power Domain constraint setting.
-===================================
-Each power domain within a system has physical constraints on voltage and
-current. This must be defined in software so that the power domain is always
-operated within specifications.
-
-Consider the following machine (again) :-
-
- Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
- |
- +-> [Consumer B @ 3.3V]
-
-This gives us two regulators and two power domains:
-
- Domain 1: Regulator-2, Consumer B.
- Domain 2: Consumer A.
-
-Constraints can be registered by calling :-
-
-int regulator_set_platform_constraints(const char *regulator,
- struct regulation_constraints *constraints);
-
-The example is defined as follows :-
-
-struct regulation_constraints domain_1 = {
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
+supply (Regulator-2). The supply regulator is set by the supply_regulator_dev
+field below:-
+
+static struct regulator_init_data regulator2_data = {
+ .supply_regulator_dev = &platform_regulator1_device.dev,
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 2000000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(regulator2_consumers),
+ .consumer_supplies = regulator2_consumers,
};
-struct regulation_constraints domain_2 = {
- .min_uV = 1800000,
- .max_uV = 2000000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
+Finally the regulator devices must be registered in the usual manner.
+
+static struct platform_device regulator_devices[] = {
+{
+ .name = "regulator",
+ .id = DCDC_1,
+ .dev = {
+ .platform_data = ®ulator1_data,
+ },
+},
+{
+ .name = "regulator",
+ .id = DCDC_2,
+ .dev = {
+ .platform_data = ®ulator2_data,
+ },
+},
};
+/* register regulator 1 device */
+platform_device_register(&wm8350_regulator_devices[0]);
-regulator_set_platform_constraints("Regulator-1", &domain_1);
-regulator_set_platform_constraints("Regulator-2", &domain_2);
+/* register regulator 2 device */
+platform_device_register(&wm8350_regulator_devices[1]);
* core.c -- Voltage/Current Regulator framework.
*
* Copyright 2007, 2008 Wolfson Microelectronics PLC.
+ * Copyright 2008 SlimLogic Ltd.
*
- * Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
+ * Author: Liam Girdwood <lrg@slimlogic.co.uk>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
struct list_head list;
struct device *dev;
const char *supply;
- const char *regulator;
+ struct regulator_dev *regulator;
};
-static inline struct regulator_dev *to_rdev(struct device *d)
-{
- return container_of(d, struct regulator_dev, dev);
-}
-
/*
* struct regulator
*
static ssize_t regulator_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
ssize_t ret;
mutex_lock(&rdev->mutex);
static ssize_t regulator_uA_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", _regulator_get_current_limit(rdev));
}
static ssize_t regulator_opmode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
int mode = _regulator_get_mode(rdev);
switch (mode) {
static ssize_t regulator_state_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
int state = _regulator_is_enabled(rdev);
if (state > 0)
static ssize_t regulator_min_uA_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "constraint not defined\n");
static ssize_t regulator_max_uA_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "constraint not defined\n");
static ssize_t regulator_min_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "constraint not defined\n");
static ssize_t regulator_max_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "constraint not defined\n");
static ssize_t regulator_total_uA_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
struct regulator *regulator;
int uA = 0;
static ssize_t regulator_num_users_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", rdev->use_count);
}
static ssize_t regulator_type_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
switch (rdev->desc->type) {
case REGULATOR_VOLTAGE:
static ssize_t regulator_suspend_mem_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_disk_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_standby_uV_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_mem_mode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_disk_mode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_standby_mode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_mem_state_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_disk_state_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static ssize_t regulator_suspend_standby_state_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
if (!rdev->constraints)
return sprintf(buf, "not defined\n");
static void regulator_dev_release(struct device *dev)
{
- struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator_dev *rdev = dev_get_drvdata(dev);
kfree(rdev);
}
/* enable & disable are mandatory for suspend control */
if (!rdev->desc->ops->set_suspend_enable ||
- !rdev->desc->ops->set_suspend_disable)
+ !rdev->desc->ops->set_suspend_disable) {
+ printk(KERN_ERR "%s: no way to set suspend state\n",
+ __func__);
return -EINVAL;
+ }
if (rstate->enabled)
ret = rdev->desc->ops->set_suspend_enable(rdev);
printk(KERN_INFO "regulator: %s: %s\n", rdev->desc->name, buf);
}
+/**
+ * set_machine_constraints - sets regulator constraints
+ * @regulator: regulator source
+ *
+ * Allows platform initialisation code to define and constrain
+ * regulator circuits e.g. valid voltage/current ranges, etc. NOTE:
+ * Constraints *must* be set by platform code in order for some
+ * regulator operations to proceed i.e. set_voltage, set_current_limit,
+ * set_mode.
+ */
+static int set_machine_constraints(struct regulator_dev *rdev,
+ struct regulation_constraints *constraints)
+{
+ int ret = 0;
+
+ rdev->constraints = constraints;
+
+ /* do we need to apply the constraint voltage */
+ if (rdev->constraints->apply_uV &&
+ rdev->constraints->min_uV == rdev->constraints->max_uV &&
+ rdev->desc->ops->set_voltage) {
+ ret = rdev->desc->ops->set_voltage(rdev,
+ rdev->constraints->min_uV, rdev->constraints->max_uV);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to apply %duV"
+ " constraint\n", __func__,
+ rdev->constraints->min_uV);
+ rdev->constraints = NULL;
+ goto out;
+ }
+ }
+
+ /* are we enabled at boot time by firmware / bootloader */
+ if (rdev->constraints->boot_on)
+ rdev->use_count = 1;
+
+ /* do we need to setup our suspend state */
+ if (constraints->initial_state)
+ ret = suspend_prepare(rdev, constraints->initial_state);
+
+ print_constraints(rdev);
+out:
+ return ret;
+}
+
+/**
+ * set_supply - set regulator supply regulator
+ * @regulator: regulator name
+ * @supply: supply regulator name
+ *
+ * Called by platform initialisation code to set the supply regulator for this
+ * regulator. This ensures that a regulators supply will also be enabled by the
+ * core if it's child is enabled.
+ */
+static int set_supply(struct regulator_dev *rdev,
+ struct regulator_dev *supply_rdev)
+{
+ int err;
+
+ err = sysfs_create_link(&rdev->dev.kobj, &supply_rdev->dev.kobj,
+ "supply");
+ if (err) {
+ printk(KERN_ERR
+ "%s: could not add device link %s err %d\n",
+ __func__, supply_rdev->dev.kobj.name, err);
+ goto out;
+ }
+ rdev->supply = supply_rdev;
+ list_add(&rdev->slist, &supply_rdev->supply_list);
+out:
+ return err;
+}
+
+/**
+ * set_consumer_device_supply: Bind a regulator to a symbolic supply
+ * @regulator: regulator source
+ * @dev: device the supply applies to
+ * @supply: symbolic name for supply
+ *
+ * Allows platform initialisation code to map physical regulator
+ * sources to symbolic names for supplies for use by devices. Devices
+ * should use these symbolic names to request regulators, avoiding the
+ * need to provide board-specific regulator names as platform data.
+ */
+static int set_consumer_device_supply(struct regulator_dev *rdev,
+ struct device *consumer_dev, const char *supply)
+{
+ struct regulator_map *node;
+
+ if (supply == NULL)
+ return -EINVAL;
+
+ node = kmalloc(sizeof(struct regulator_map), GFP_KERNEL);
+ if (node == NULL)
+ return -ENOMEM;
+
+ node->regulator = rdev;
+ node->dev = consumer_dev;
+ node->supply = supply;
+
+ list_add(&node->list, ®ulator_map_list);
+ return 0;
+}
+
+static void unset_consumer_device_supply(struct regulator_dev *rdev,
+ struct device *consumer_dev)
+{
+ struct regulator_map *node, *n;
+
+ list_for_each_entry_safe(node, n, ®ulator_map_list, list) {
+ if (rdev == node->regulator &&
+ consumer_dev == node->dev) {
+ list_del(&node->list);
+ kfree(node);
+ return;
+ }
+ }
+}
+
#define REG_STR_SIZE 32
static struct regulator *create_regulator(struct regulator_dev *rdev,
struct regulator_dev *rdev;
struct regulator_map *map;
struct regulator *regulator = ERR_PTR(-ENODEV);
- const char *supply = id;
if (id == NULL) {
printk(KERN_ERR "regulator: get() with no identifier\n");
list_for_each_entry(map, ®ulator_map_list, list) {
if (dev == map->dev &&
strcmp(map->supply, id) == 0) {
- supply = map->regulator;
- break;
- }
- }
-
- list_for_each_entry(rdev, ®ulator_list, list) {
- if (strcmp(supply, rdev->desc->name) == 0 &&
- try_module_get(rdev->owner))
+ rdev = map->regulator;
goto found;
+ }
}
printk(KERN_ERR "regulator: Unable to get requested regulator: %s\n",
id);
return regulator;
found:
+ if (!try_module_get(rdev->owner))
+ goto out;
+
regulator = create_regulator(rdev, dev, id);
if (regulator == NULL) {
regulator = ERR_PTR(-ENOMEM);
module_put(rdev->owner);
}
+out:
mutex_unlock(®ulator_list_mutex);
return regulator;
}
* Returns 0 on success.
*/
struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
- void *reg_data)
+ struct device *dev, void *driver_data)
{
static atomic_t regulator_no = ATOMIC_INIT(0);
struct regulator_dev *rdev;
- int ret;
+ struct regulator_init_data *init_data = dev->platform_data;
+ int ret, i;
if (regulator_desc == NULL)
return ERR_PTR(-EINVAL);
mutex_lock(®ulator_list_mutex);
mutex_init(&rdev->mutex);
- rdev->reg_data = reg_data;
+ rdev->reg_data = driver_data;
rdev->owner = regulator_desc->owner;
rdev->desc = regulator_desc;
INIT_LIST_HEAD(&rdev->consumer_list);
INIT_LIST_HEAD(&rdev->slist);
BLOCKING_INIT_NOTIFIER_HEAD(&rdev->notifier);
+ /* preform any regulator specific init */
+ if (init_data->regulator_init) {
+ ret = init_data->regulator_init(rdev->reg_data);
+ if (ret < 0) {
+ kfree(rdev);
+ rdev = ERR_PTR(ret);
+ goto out;
+ }
+ }
+
+ /* set regulator constraints */
+ ret = set_machine_constraints(rdev, &init_data->constraints);
+ if (ret < 0) {
+ kfree(rdev);
+ rdev = ERR_PTR(ret);
+ goto out;
+ }
+
+ /* register with sysfs */
rdev->dev.class = ®ulator_class;
- device_initialize(&rdev->dev);
+ rdev->dev.parent = dev;
snprintf(rdev->dev.bus_id, sizeof(rdev->dev.bus_id),
- "regulator_%ld_%s",
- (unsigned long)atomic_inc_return(®ulator_no) - 1,
- regulator_desc->name);
-
- ret = device_add(&rdev->dev);
- if (ret == 0)
- list_add(&rdev->list, ®ulator_list);
- else {
+ "regulator.%d", atomic_inc_return(®ulator_no) - 1);
+ ret = device_register(&rdev->dev);
+ if (ret != 0) {
kfree(rdev);
rdev = ERR_PTR(ret);
+ goto out;
+ }
+
+ dev_set_drvdata(&rdev->dev, rdev);
+
+ /* set supply regulator if it exists */
+ if (init_data->supply_regulator_dev) {
+ ret = set_supply(rdev,
+ dev_get_drvdata(init_data->supply_regulator_dev));
+ if (ret < 0) {
+ device_unregister(&rdev->dev);
+ kfree(rdev);
+ rdev = ERR_PTR(ret);
+ goto out;
+ }
+ }
+
+ /* add consumers devices */
+ for (i = 0; i < init_data->num_consumer_supplies; i++) {
+ ret = set_consumer_device_supply(rdev,
+ init_data->consumer_supplies[i].dev,
+ init_data->consumer_supplies[i].supply);
+ if (ret < 0) {
+ for (--i; i >= 0; i--)
+ unset_consumer_device_supply(rdev,
+ init_data->consumer_supplies[i].dev);
+ device_unregister(&rdev->dev);
+ kfree(rdev);
+ rdev = ERR_PTR(ret);
+ goto out;
+ }
}
+
+ list_add(&rdev->list, ®ulator_list);
+out:
mutex_unlock(®ulator_list_mutex);
return rdev;
}
}
EXPORT_SYMBOL_GPL(regulator_unregister);
-/**
- * regulator_set_supply - set regulator supply regulator
- * @regulator: regulator name
- * @supply: supply regulator name
- *
- * Called by platform initialisation code to set the supply regulator for this
- * regulator. This ensures that a regulators supply will also be enabled by the
- * core if it's child is enabled.
- */
-int regulator_set_supply(const char *regulator, const char *supply)
-{
- struct regulator_dev *rdev, *supply_rdev;
- int err;
-
- if (regulator == NULL || supply == NULL)
- return -EINVAL;
-
- mutex_lock(®ulator_list_mutex);
-
- list_for_each_entry(rdev, ®ulator_list, list) {
- if (!strcmp(rdev->desc->name, regulator))
- goto found_regulator;
- }
- mutex_unlock(®ulator_list_mutex);
- return -ENODEV;
-
-found_regulator:
- list_for_each_entry(supply_rdev, ®ulator_list, list) {
- if (!strcmp(supply_rdev->desc->name, supply))
- goto found_supply;
- }
- mutex_unlock(®ulator_list_mutex);
- return -ENODEV;
-
-found_supply:
- err = sysfs_create_link(&rdev->dev.kobj, &supply_rdev->dev.kobj,
- "supply");
- if (err) {
- printk(KERN_ERR
- "%s: could not add device link %s err %d\n",
- __func__, supply_rdev->dev.kobj.name, err);
- goto out;
- }
- rdev->supply = supply_rdev;
- list_add(&rdev->slist, &supply_rdev->supply_list);
-out:
- mutex_unlock(®ulator_list_mutex);
- return err;
-}
-EXPORT_SYMBOL_GPL(regulator_set_supply);
-
-/**
- * regulator_get_supply - get regulator supply regulator
- * @regulator: regulator name
- *
- * Returns the supply supply regulator name or NULL if no supply regulator
- * exists (i.e the regulator is supplied directly from USB, Line, Battery, etc)
- */
-const char *regulator_get_supply(const char *regulator)
-{
- struct regulator_dev *rdev;
-
- if (regulator == NULL)
- return NULL;
-
- mutex_lock(®ulator_list_mutex);
- list_for_each_entry(rdev, ®ulator_list, list) {
- if (!strcmp(rdev->desc->name, regulator))
- goto found;
- }
- mutex_unlock(®ulator_list_mutex);
- return NULL;
-
-found:
- mutex_unlock(®ulator_list_mutex);
- if (rdev->supply)
- return rdev->supply->desc->name;
- else
- return NULL;
-}
-EXPORT_SYMBOL_GPL(regulator_get_supply);
-
-/**
- * regulator_set_machine_constraints - sets regulator constraints
- * @regulator: regulator source
- *
- * Allows platform initialisation code to define and constrain
- * regulator circuits e.g. valid voltage/current ranges, etc. NOTE:
- * Constraints *must* be set by platform code in order for some
- * regulator operations to proceed i.e. set_voltage, set_current_limit,
- * set_mode.
- */
-int regulator_set_machine_constraints(const char *regulator_name,
- struct regulation_constraints *constraints)
-{
- struct regulator_dev *rdev;
- int ret = 0;
-
- if (regulator_name == NULL)
- return -EINVAL;
-
- mutex_lock(®ulator_list_mutex);
-
- list_for_each_entry(rdev, ®ulator_list, list) {
- if (!strcmp(regulator_name, rdev->desc->name))
- goto found;
- }
- ret = -ENODEV;
- goto out;
-
-found:
- mutex_lock(&rdev->mutex);
- rdev->constraints = constraints;
-
- /* do we need to apply the constraint voltage */
- if (rdev->constraints->apply_uV &&
- rdev->constraints->min_uV == rdev->constraints->max_uV &&
- rdev->desc->ops->set_voltage) {
- ret = rdev->desc->ops->set_voltage(rdev,
- rdev->constraints->min_uV, rdev->constraints->max_uV);
- if (ret < 0) {
- printk(KERN_ERR "%s: failed to apply %duV"
- " constraint\n", __func__,
- rdev->constraints->min_uV);
- rdev->constraints = NULL;
- goto out;
- }
- }
-
- /* are we enabled at boot time by firmware / bootloader */
- if (rdev->constraints->boot_on)
- rdev->use_count = 1;
-
- /* do we need to setup our suspend state */
- if (constraints->initial_state)
- ret = suspend_prepare(rdev, constraints->initial_state);
-
- print_constraints(rdev);
- mutex_unlock(&rdev->mutex);
-
-out:
- mutex_unlock(®ulator_list_mutex);
- return ret;
-}
-EXPORT_SYMBOL_GPL(regulator_set_machine_constraints);
-
-
-/**
- * regulator_set_device_supply: Bind a regulator to a symbolic supply
- * @regulator: regulator source
- * @dev: device the supply applies to
- * @supply: symbolic name for supply
- *
- * Allows platform initialisation code to map physical regulator
- * sources to symbolic names for supplies for use by devices. Devices
- * should use these symbolic names to request regulators, avoiding the
- * need to provide board-specific regulator names as platform data.
- */
-int regulator_set_device_supply(const char *regulator, struct device *dev,
- const char *supply)
-{
- struct regulator_map *node;
-
- if (regulator == NULL || supply == NULL)
- return -EINVAL;
-
- node = kmalloc(sizeof(struct regulator_map), GFP_KERNEL);
- if (node == NULL)
- return -ENOMEM;
-
- node->regulator = regulator;
- node->dev = dev;
- node->supply = supply;
-
- mutex_lock(®ulator_list_mutex);
- list_add(&node->list, ®ulator_map_list);
- mutex_unlock(®ulator_list_mutex);
- return 0;
-}
-EXPORT_SYMBOL_GPL(regulator_set_device_supply);
-
/**
* regulator_suspend_prepare: prepare regulators for system wide suspend
* @state: system suspend state
}
EXPORT_SYMBOL_GPL(rdev_get_id);
+struct device *rdev_get_dev(struct regulator_dev *rdev)
+{
+ return &rdev->dev;
+}
+EXPORT_SYMBOL_GPL(rdev_get_dev);
+
+void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data)
+{
+ return reg_init_data->driver_data;
+}
+EXPORT_SYMBOL_GPL(regulator_get_init_drvdata);
+
static int __init regulator_init(void)
{
printk(KERN_INFO "regulator: core version %s\n", REGULATOR_VERSION);
projects / linux-2.6-omap-h63xx.git / commitdiff