#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.26-rc8
-# Wed Jun 25 13:39:12 2008
+# Thu Jul 3 11:48:41 2008
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_NO_IOPORT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
#
# Non-8250 serial port support
#
+CONFIG_SERIAL_SAMSUNG=y
+# CONFIG_SERIAL_SAMSUNG_DEBUG is not set
+CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_SERIAL_S3C2410=y
-CONFIG_SERIAL_S3C2410_CONSOLE=y
+CONFIG_SERIAL_S3C2412=y
+CONFIG_SERIAL_S3C2440=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
# CONFIG_SAMPLES is not set
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_ERRORS=y
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
-config SERIAL_S3C2410
- tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support"
- depends on ARM && ARCH_S3C2410
- select SERIAL_CORE
+config SERIAL_SAMSUNG
+ tristate "Samsung SoC serial support"
+ depends on ARM && PLAT_S3C24XX
help
Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
providing /dev/ttySAC0, 1 and 2 (note, some machines may not
provide all of these ports, depending on how the serial port
pins are configured.
- Currently this driver supports the UARTS on the S3C2410, S3C2440,
- S3C2442, S3C2412 and S3C2413 CPUs.
+config SERIAL_SAMSUNG_DEBUG
+ bool "Samsung SoC serial debug"
+ depends on SERIAL_SAMSUNG
+ help
+ Add support for debugging the serial driver. Since this is
+ generally being used as a console, we use our own output
+ routines that go via the low-level debug printascii()
+ function.
-config SERIAL_S3C2410_CONSOLE
- bool "Support for console on S3C2410 serial port"
- depends on SERIAL_S3C2410=y
+config SERIAL_SAMSUNG_CONSOLE
+ bool "Support for console on Samsung SoC serial port"
+ depends on SERIAL_SAMSUNG=y
select SERIAL_CORE_CONSOLE
help
Allow selection of the S3C24XX on-board serial ports for use as
your boot loader about how to pass options to the kernel at
boot time.)
+config SERIAL_S3C2400
+ tristate "Samsung S3C2410 Serial port support"
+ depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
+ default y if CPU_S3C2400
+ help
+ Serial port support for the Samsung S3C2400 SoC
+
+config SERIAL_S3C2410
+ tristate "Samsung S3C2410 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S3C2410
+ default y if CPU_S3C2410
+ help
+ Serial port support for the Samsung S3C2410 SoC
+
+config SERIAL_S3C2412
+ tristate "Samsung S3C2412/S3C2413 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S3C2412
+ default y if CPU_S3C2412
+ help
+ Serial port support for the Samsung S3C2412 and S3C2413 SoC
+
+config SERIAL_S3C2440
+ tristate "Samsung S3C2440/S3C2442 Serial port support"
+ depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442)
+ default y if CPU_S3C2440
+ default y if CPU_S3C2442
+ help
+ Serial port support for the Samsung S3C2440 and S3C2442 SoC
+
+
+
config SERIAL_DZ
bool "DECstation DZ serial driver"
depends on MACH_DECSTATION && 32BIT
obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
+obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
+obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o
obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
+obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
+obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
--- /dev/null
+/* linux/drivers/serial/s3c240.c
+ *
+ * Driver for Samsung SoC onboard UARTs.
+ *
+ * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+
+#include <asm/irq.h>
+
+#include <asm/hardware.h>
+
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+
+#include "samsung.h"
+
+static int s3c2400_serial_getsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ clk->divisor = 1;
+ clk->name = "pclk";
+
+ return 0;
+}
+
+static int s3c2400_serial_setsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ return 0;
+}
+
+static int s3c2400_serial_resetport(struct uart_port *port,
+ struct s3c2410_uartcfg *cfg)
+{
+ dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n",
+ port, port->mapbase, cfg);
+
+ wr_regl(port, S3C2410_UCON, cfg->ucon);
+ wr_regl(port, S3C2410_ULCON, cfg->ulcon);
+
+ /* reset both fifos */
+
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon);
+
+ return 0;
+}
+
+static struct s3c24xx_uart_info s3c2400_uart_inf = {
+ .name = "Samsung S3C2400 UART",
+ .type = PORT_S3C2400,
+ .fifosize = 16,
+ .rx_fifomask = S3C2410_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2410_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2410_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2410_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
+ .get_clksrc = s3c2400_serial_getsource,
+ .set_clksrc = s3c2400_serial_setsource,
+ .reset_port = s3c2400_serial_resetport,
+};
+
+static int s3c2400_serial_probe(struct platform_device *dev)
+{
+ return s3c24xx_serial_probe(dev, &s3c2400_uart_inf);
+}
+
+static struct platform_driver s3c2400_serial_drv = {
+ .probe = s3c2400_serial_probe,
+ .remove = s3c24xx_serial_remove,
+ .driver = {
+ .name = "s3c2400-uart",
+ .owner = THIS_MODULE,
+ },
+};
+
+s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf);
+
+static inline int s3c2400_serial_init(void)
+{
+ return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf);
+}
+
+static inline void s3c2400_serial_exit(void)
+{
+ platform_driver_unregister(&s3c2400_serial_drv);
+}
+
+module_init(s3c2400_serial_init);
+module_exit(s3c2400_serial_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver");
+MODULE_ALIAS("platform:s3c2400-uart");
/* linux/drivers/serial/s3c2410.c
*
- * Driver for Samsung SoC onboard UARTs.
+ * Driver for Samsung S3C2410 SoC onboard UARTs.
*
- * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics
+ * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics
* http://armlinux.simtec.co.uk/
*
* This program is free software; you can redistribute it and/or modify
* published by the Free Software Foundation.
*/
-/* Note on 2440 fclk clock source handling
- *
- * Whilst it is possible to use the fclk as clock source, the method
- * of properly switching too/from this is currently un-implemented, so
- * whichever way is configured at startup is the one that will be used.
-*/
-
-/* Hote on 2410 error handling
- *
- * The s3c2410 manual has a love/hate affair with the contents of the
- * UERSTAT register in the UART blocks, and keeps marking some of the
- * error bits as reserved. Having checked with the s3c2410x01,
- * it copes with BREAKs properly, so I am happy to ignore the RESERVED
- * feature from the latter versions of the manual.
- *
- * If it becomes aparrent that latter versions of the 2410 remove these
- * bits, then action will have to be taken to differentiate the versions
- * and change the policy on BREAK
- *
- * BJD, 04-Nov-2004
-*/
-
-
-#if defined(CONFIG_SERIAL_S3C2410_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/sysrq.h>
-#include <linux/console.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#include <asm/hardware.h>
-
-#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-
-/* structures */
-
-struct s3c24xx_uart_info {
- char *name;
- unsigned int type;
- unsigned int fifosize;
- unsigned long rx_fifomask;
- unsigned long rx_fifoshift;
- unsigned long rx_fifofull;
- unsigned long tx_fifomask;
- unsigned long tx_fifoshift;
- unsigned long tx_fifofull;
-
- /* clock source control */
-
- int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
- int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
-
- /* uart controls */
- int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *);
-};
-
-struct s3c24xx_uart_port {
- unsigned char rx_claimed;
- unsigned char tx_claimed;
-
- struct s3c24xx_uart_info *info;
- struct s3c24xx_uart_clksrc *clksrc;
- struct clk *clk;
- struct clk *baudclk;
- struct uart_port port;
-};
-
-
-/* configuration defines */
-
-#if 0
-#if 1
-/* send debug to the low-level output routines */
-
-extern void printascii(const char *);
-
-static void
-s3c24xx_serial_dbg(const char *fmt, ...)
-{
- va_list va;
- char buff[256];
-
- va_start(va, fmt);
- vsprintf(buff, fmt, va);
- va_end(va);
-
- printascii(buff);
-}
-
-#define dbg(x...) s3c24xx_serial_dbg(x)
-
-#else
-#define dbg(x...) printk(KERN_DEBUG "s3c24xx: ");
-#endif
-#else /* no debug */
-#define dbg(x...) do {} while(0)
-#endif
-
-/* UART name and device definitions */
-
-#define S3C24XX_SERIAL_NAME "ttySAC"
-#define S3C24XX_SERIAL_MAJOR 204
-#define S3C24XX_SERIAL_MINOR 64
-
-
-/* conversion functions */
-
-#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev)
-#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data)
-
-/* we can support 3 uarts, but not always use them */
-
-#ifdef CONFIG_CPU_S3C2400
-#define NR_PORTS (2)
-#else
-#define NR_PORTS (3)
-#endif
-
-/* port irq numbers */
-
-#define TX_IRQ(port) ((port)->irq + 1)
-#define RX_IRQ(port) ((port)->irq)
-
-/* register access controls */
-
-#define portaddr(port, reg) ((port)->membase + (reg))
-
-#define rd_regb(port, reg) (__raw_readb(portaddr(port, reg)))
-#define rd_regl(port, reg) (__raw_readl(portaddr(port, reg)))
-
-#define wr_regb(port, reg, val) \
- do { __raw_writeb(val, portaddr(port, reg)); } while(0)
-
-#define wr_regl(port, reg, val) \
- do { __raw_writel(val, portaddr(port, reg)); } while(0)
-
-/* macros to change one thing to another */
-
-#define tx_enabled(port) ((port)->unused[0])
-#define rx_enabled(port) ((port)->unused[1])
-
-/* flag to ignore all characters comming in */
-#define RXSTAT_DUMMY_READ (0x10000000)
-
-static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port)
-{
- return container_of(port, struct s3c24xx_uart_port, port);
-}
-
-/* translate a port to the device name */
-
-static inline const char *s3c24xx_serial_portname(struct uart_port *port)
-{
- return to_platform_device(port->dev)->name;
-}
-
-static int s3c24xx_serial_txempty_nofifo(struct uart_port *port)
-{
- return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE);
-}
-
-static void s3c24xx_serial_rx_enable(struct uart_port *port)
-{
- unsigned long flags;
- unsigned int ucon, ufcon;
- int count = 10000;
-
- spin_lock_irqsave(&port->lock, flags);
-
- while (--count && !s3c24xx_serial_txempty_nofifo(port))
- udelay(100);
-
- ufcon = rd_regl(port, S3C2410_UFCON);
- ufcon |= S3C2410_UFCON_RESETRX;
- wr_regl(port, S3C2410_UFCON, ufcon);
-
- ucon = rd_regl(port, S3C2410_UCON);
- ucon |= S3C2410_UCON_RXIRQMODE;
- wr_regl(port, S3C2410_UCON, ucon);
-
- rx_enabled(port) = 1;
- spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static void s3c24xx_serial_rx_disable(struct uart_port *port)
-{
- unsigned long flags;
- unsigned int ucon;
-
- spin_lock_irqsave(&port->lock, flags);
-
- ucon = rd_regl(port, S3C2410_UCON);
- ucon &= ~S3C2410_UCON_RXIRQMODE;
- wr_regl(port, S3C2410_UCON, ucon);
-
- rx_enabled(port) = 0;
- spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static void s3c24xx_serial_stop_tx(struct uart_port *port)
-{
- if (tx_enabled(port)) {
- disable_irq(TX_IRQ(port));
- tx_enabled(port) = 0;
- if (port->flags & UPF_CONS_FLOW)
- s3c24xx_serial_rx_enable(port);
- }
-}
-
-static void s3c24xx_serial_start_tx(struct uart_port *port)
-{
- if (!tx_enabled(port)) {
- if (port->flags & UPF_CONS_FLOW)
- s3c24xx_serial_rx_disable(port);
-
- enable_irq(TX_IRQ(port));
- tx_enabled(port) = 1;
- }
-}
-
-
-static void s3c24xx_serial_stop_rx(struct uart_port *port)
-{
- if (rx_enabled(port)) {
- dbg("s3c24xx_serial_stop_rx: port=%p\n", port);
- disable_irq(RX_IRQ(port));
- rx_enabled(port) = 0;
- }
-}
-
-static void s3c24xx_serial_enable_ms(struct uart_port *port)
-{
-}
-
-static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port)
-{
- return to_ourport(port)->info;
-}
-
-static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port)
-{
- if (port->dev == NULL)
- return NULL;
-
- return (struct s3c2410_uartcfg *)port->dev->platform_data;
-}
-
-static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport,
- unsigned long ufstat)
-{
- struct s3c24xx_uart_info *info = ourport->info;
-
- if (ufstat & info->rx_fifofull)
- return info->fifosize;
-
- return (ufstat & info->rx_fifomask) >> info->rx_fifoshift;
-}
-
-
-/* ? - where has parity gone?? */
-#define S3C2410_UERSTAT_PARITY (0x1000)
-
-static irqreturn_t
-s3c24xx_serial_rx_chars(int irq, void *dev_id)
-{
- struct s3c24xx_uart_port *ourport = dev_id;
- struct uart_port *port = &ourport->port;
- struct tty_struct *tty = port->info->tty;
- unsigned int ufcon, ch, flag, ufstat, uerstat;
- int max_count = 64;
-
- while (max_count-- > 0) {
- ufcon = rd_regl(port, S3C2410_UFCON);
- ufstat = rd_regl(port, S3C2410_UFSTAT);
-
- if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
- break;
-
- uerstat = rd_regl(port, S3C2410_UERSTAT);
- ch = rd_regb(port, S3C2410_URXH);
-
- if (port->flags & UPF_CONS_FLOW) {
- int txe = s3c24xx_serial_txempty_nofifo(port);
-
- if (rx_enabled(port)) {
- if (!txe) {
- rx_enabled(port) = 0;
- continue;
- }
- } else {
- if (txe) {
- ufcon |= S3C2410_UFCON_RESETRX;
- wr_regl(port, S3C2410_UFCON, ufcon);
- rx_enabled(port) = 1;
- goto out;
- }
- continue;
- }
- }
-
- /* insert the character into the buffer */
-
- flag = TTY_NORMAL;
- port->icount.rx++;
-
- if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) {
- dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n",
- ch, uerstat);
-
- /* check for break */
- if (uerstat & S3C2410_UERSTAT_BREAK) {
- dbg("break!\n");
- port->icount.brk++;
- if (uart_handle_break(port))
- goto ignore_char;
- }
-
- if (uerstat & S3C2410_UERSTAT_FRAME)
- port->icount.frame++;
- if (uerstat & S3C2410_UERSTAT_OVERRUN)
- port->icount.overrun++;
-
- uerstat &= port->read_status_mask;
-
- if (uerstat & S3C2410_UERSTAT_BREAK)
- flag = TTY_BREAK;
- else if (uerstat & S3C2410_UERSTAT_PARITY)
- flag = TTY_PARITY;
- else if (uerstat & ( S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_OVERRUN))
- flag = TTY_FRAME;
- }
-
- if (uart_handle_sysrq_char(port, ch))
- goto ignore_char;
-
- uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN, ch, flag);
-
- ignore_char:
- continue;
- }
- tty_flip_buffer_push(tty);
-
- out:
- return IRQ_HANDLED;
-}
-
-static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id)
-{
- struct s3c24xx_uart_port *ourport = id;
- struct uart_port *port = &ourport->port;
- struct circ_buf *xmit = &port->info->xmit;
- int count = 256;
-
- if (port->x_char) {
- wr_regb(port, S3C2410_UTXH, port->x_char);
- port->icount.tx++;
- port->x_char = 0;
- goto out;
- }
-
- /* if there isnt anything more to transmit, or the uart is now
- * stopped, disable the uart and exit
- */
-
- if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
- s3c24xx_serial_stop_tx(port);
- goto out;
- }
-
- /* try and drain the buffer... */
-
- while (!uart_circ_empty(xmit) && count-- > 0) {
- if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull)
- break;
-
- wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]);
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- port->icount.tx++;
- }
-
- if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
- uart_write_wakeup(port);
-
- if (uart_circ_empty(xmit))
- s3c24xx_serial_stop_tx(port);
-
- out:
- return IRQ_HANDLED;
-}
-
-static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT);
- unsigned long ufcon = rd_regl(port, S3C2410_UFCON);
-
- if (ufcon & S3C2410_UFCON_FIFOMODE) {
- if ((ufstat & info->tx_fifomask) != 0 ||
- (ufstat & info->tx_fifofull))
- return 0;
-
- return 1;
- }
-
- return s3c24xx_serial_txempty_nofifo(port);
-}
-
-/* no modem control lines */
-static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
-{
- unsigned int umstat = rd_regb(port,S3C2410_UMSTAT);
-
- if (umstat & S3C2410_UMSTAT_CTS)
- return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
- else
- return TIOCM_CAR | TIOCM_DSR;
-}
-
-static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
- /* todo - possibly remove AFC and do manual CTS */
-}
-
-static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
-{
- unsigned long flags;
- unsigned int ucon;
-
- spin_lock_irqsave(&port->lock, flags);
-
- ucon = rd_regl(port, S3C2410_UCON);
-
- if (break_state)
- ucon |= S3C2410_UCON_SBREAK;
- else
- ucon &= ~S3C2410_UCON_SBREAK;
-
- wr_regl(port, S3C2410_UCON, ucon);
-
- spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static void s3c24xx_serial_shutdown(struct uart_port *port)
-{
- struct s3c24xx_uart_port *ourport = to_ourport(port);
-
- if (ourport->tx_claimed) {
- free_irq(TX_IRQ(port), ourport);
- tx_enabled(port) = 0;
- ourport->tx_claimed = 0;
- }
-
- if (ourport->rx_claimed) {
- free_irq(RX_IRQ(port), ourport);
- ourport->rx_claimed = 0;
- rx_enabled(port) = 0;
- }
-}
-
-
-static int s3c24xx_serial_startup(struct uart_port *port)
-{
- struct s3c24xx_uart_port *ourport = to_ourport(port);
- int ret;
-
- dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n",
- port->mapbase, port->membase);
-
- rx_enabled(port) = 1;
-
- ret = request_irq(RX_IRQ(port),
- s3c24xx_serial_rx_chars, 0,
- s3c24xx_serial_portname(port), ourport);
-
- if (ret != 0) {
- printk(KERN_ERR "cannot get irq %d\n", RX_IRQ(port));
- return ret;
- }
-
- ourport->rx_claimed = 1;
-
- dbg("requesting tx irq...\n");
-
- tx_enabled(port) = 1;
-
- ret = request_irq(TX_IRQ(port),
- s3c24xx_serial_tx_chars, 0,
- s3c24xx_serial_portname(port), ourport);
-
- if (ret) {
- printk(KERN_ERR "cannot get irq %d\n", TX_IRQ(port));
- goto err;
- }
-
- ourport->tx_claimed = 1;
-
- dbg("s3c24xx_serial_startup ok\n");
-
- /* the port reset code should have done the correct
- * register setup for the port controls */
-
- return ret;
-
- err:
- s3c24xx_serial_shutdown(port);
- return ret;
-}
-
-/* power power management control */
-
-static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
- unsigned int old)
-{
- struct s3c24xx_uart_port *ourport = to_ourport(port);
-
- switch (level) {
- case 3:
- if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
- clk_disable(ourport->baudclk);
-
- clk_disable(ourport->clk);
- break;
-
- case 0:
- clk_enable(ourport->clk);
-
- if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
- clk_enable(ourport->baudclk);
-
- break;
- default:
- printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level);
- }
-}
-
-/* baud rate calculation
- *
- * The UARTs on the S3C2410/S3C2440 can take their clocks from a number
- * of different sources, including the peripheral clock ("pclk") and an
- * external clock ("uclk"). The S3C2440 also adds the core clock ("fclk")
- * with a programmable extra divisor.
- *
- * The following code goes through the clock sources, and calculates the
- * baud clocks (and the resultant actual baud rates) and then tries to
- * pick the closest one and select that.
- *
-*/
-
-
-#define MAX_CLKS (8)
-
-static struct s3c24xx_uart_clksrc tmp_clksrc = {
- .name = "pclk",
- .min_baud = 0,
- .max_baud = 0,
- .divisor = 1,
-};
-
-static inline int
-s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
-
- return (info->get_clksrc)(port, c);
-}
-
-static inline int
-s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
-
- return (info->set_clksrc)(port, c);
-}
-
-struct baud_calc {
- struct s3c24xx_uart_clksrc *clksrc;
- unsigned int calc;
- unsigned int quot;
- struct clk *src;
-};
-
-static int s3c24xx_serial_calcbaud(struct baud_calc *calc,
- struct uart_port *port,
- struct s3c24xx_uart_clksrc *clksrc,
- unsigned int baud)
-{
- unsigned long rate;
-
- calc->src = clk_get(port->dev, clksrc->name);
- if (calc->src == NULL || IS_ERR(calc->src))
- return 0;
-
- rate = clk_get_rate(calc->src);
- rate /= clksrc->divisor;
-
- calc->clksrc = clksrc;
- calc->quot = (rate + (8 * baud)) / (16 * baud);
- calc->calc = (rate / (calc->quot * 16));
-
- calc->quot--;
- return 1;
-}
-
-static unsigned int s3c24xx_serial_getclk(struct uart_port *port,
- struct s3c24xx_uart_clksrc **clksrc,
- struct clk **clk,
- unsigned int baud)
-{
- struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
- struct s3c24xx_uart_clksrc *clkp;
- struct baud_calc res[MAX_CLKS];
- struct baud_calc *resptr, *best, *sptr;
- int i;
-
- clkp = cfg->clocks;
- best = NULL;
-
- if (cfg->clocks_size < 2) {
- if (cfg->clocks_size == 0)
- clkp = &tmp_clksrc;
-
- /* check to see if we're sourcing fclk, and if so we're
- * going to have to update the clock source
- */
-
- if (strcmp(clkp->name, "fclk") == 0) {
- struct s3c24xx_uart_clksrc src;
-
- s3c24xx_serial_getsource(port, &src);
-
- /* check that the port already using fclk, and if
- * not, then re-select fclk
- */
-
- if (strcmp(src.name, clkp->name) == 0) {
- s3c24xx_serial_setsource(port, clkp);
- s3c24xx_serial_getsource(port, &src);
- }
-
- clkp->divisor = src.divisor;
- }
-
- s3c24xx_serial_calcbaud(res, port, clkp, baud);
- best = res;
- resptr = best + 1;
- } else {
- resptr = res;
-
- for (i = 0; i < cfg->clocks_size; i++, clkp++) {
- if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud))
- resptr++;
- }
- }
-
- /* ok, we now need to select the best clock we found */
-
- if (!best) {
- unsigned int deviation = (1<<30)|((1<<30)-1);
- int calc_deviation;
-
- for (sptr = res; sptr < resptr; sptr++) {
- calc_deviation = baud - sptr->calc;
- if (calc_deviation < 0)
- calc_deviation = -calc_deviation;
-
- if (calc_deviation < deviation) {
- best = sptr;
- deviation = calc_deviation;
- }
- }
- }
-
- /* store results to pass back */
-
- *clksrc = best->clksrc;
- *clk = best->src;
-
- return best->quot;
-}
-
-static void s3c24xx_serial_set_termios(struct uart_port *port,
- struct ktermios *termios,
- struct ktermios *old)
-{
- struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
- struct s3c24xx_uart_port *ourport = to_ourport(port);
- struct s3c24xx_uart_clksrc *clksrc = NULL;
- struct clk *clk = NULL;
- unsigned long flags;
- unsigned int baud, quot;
- unsigned int ulcon;
- unsigned int umcon;
-
- /*
- * We don't support modem control lines.
- */
- termios->c_cflag &= ~(HUPCL | CMSPAR);
- termios->c_cflag |= CLOCAL;
-
- /*
- * Ask the core to calculate the divisor for us.
- */
-
- baud = uart_get_baud_rate(port, termios, old, 0, 115200*8);
-
- if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
- quot = port->custom_divisor;
- else
- quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud);
-
- /* check to see if we need to change clock source */
-
- if (ourport->clksrc != clksrc || ourport->baudclk != clk) {
- s3c24xx_serial_setsource(port, clksrc);
-
- if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
- clk_disable(ourport->baudclk);
- ourport->baudclk = NULL;
- }
-
- clk_enable(clk);
-
- ourport->clksrc = clksrc;
- ourport->baudclk = clk;
- }
-
- switch (termios->c_cflag & CSIZE) {
- case CS5:
- dbg("config: 5bits/char\n");
- ulcon = S3C2410_LCON_CS5;
- break;
- case CS6:
- dbg("config: 6bits/char\n");
- ulcon = S3C2410_LCON_CS6;
- break;
- case CS7:
- dbg("config: 7bits/char\n");
- ulcon = S3C2410_LCON_CS7;
- break;
- case CS8:
- default:
- dbg("config: 8bits/char\n");
- ulcon = S3C2410_LCON_CS8;
- break;
- }
-
- /* preserve original lcon IR settings */
- ulcon |= (cfg->ulcon & S3C2410_LCON_IRM);
-
- if (termios->c_cflag & CSTOPB)
- ulcon |= S3C2410_LCON_STOPB;
-
- umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0;
-
- if (termios->c_cflag & PARENB) {
- if (termios->c_cflag & PARODD)
- ulcon |= S3C2410_LCON_PODD;
- else
- ulcon |= S3C2410_LCON_PEVEN;
- } else {
- ulcon |= S3C2410_LCON_PNONE;
- }
-
- spin_lock_irqsave(&port->lock, flags);
-
- dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot);
-
- wr_regl(port, S3C2410_ULCON, ulcon);
- wr_regl(port, S3C2410_UBRDIV, quot);
- wr_regl(port, S3C2410_UMCON, umcon);
-
- dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
- rd_regl(port, S3C2410_ULCON),
- rd_regl(port, S3C2410_UCON),
- rd_regl(port, S3C2410_UFCON));
-
- /*
- * Update the per-port timeout.
- */
- uart_update_timeout(port, termios->c_cflag, baud);
-
- /*
- * Which character status flags are we interested in?
- */
- port->read_status_mask = S3C2410_UERSTAT_OVERRUN;
- if (termios->c_iflag & INPCK)
- port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY;
-
- /*
- * Which character status flags should we ignore?
- */
- port->ignore_status_mask = 0;
- if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN;
- if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= S3C2410_UERSTAT_FRAME;
-
- /*
- * Ignore all characters if CREAD is not set.
- */
- if ((termios->c_cflag & CREAD) == 0)
- port->ignore_status_mask |= RXSTAT_DUMMY_READ;
-
- spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static const char *s3c24xx_serial_type(struct uart_port *port)
-{
- switch (port->type) {
- case PORT_S3C2410:
- return "S3C2410";
- case PORT_S3C2440:
- return "S3C2440";
- case PORT_S3C2412:
- return "S3C2412";
- default:
- return NULL;
- }
-}
-
-#define MAP_SIZE (0x100)
-
-static void s3c24xx_serial_release_port(struct uart_port *port)
-{
- release_mem_region(port->mapbase, MAP_SIZE);
-}
-
-static int s3c24xx_serial_request_port(struct uart_port *port)
-{
- const char *name = s3c24xx_serial_portname(port);
- return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY;
-}
-
-static void s3c24xx_serial_config_port(struct uart_port *port, int flags)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
-
- if (flags & UART_CONFIG_TYPE &&
- s3c24xx_serial_request_port(port) == 0)
- port->type = info->type;
-}
-
-/*
- * verify the new serial_struct (for TIOCSSERIAL).
- */
-static int
-s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
-
- if (ser->type != PORT_UNKNOWN && ser->type != info->type)
- return -EINVAL;
-
- return 0;
-}
-
-
-#ifdef CONFIG_SERIAL_S3C2410_CONSOLE
-
-static struct console s3c24xx_serial_console;
-
-#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console
-#else
-#define S3C24XX_SERIAL_CONSOLE NULL
-#endif
-
-static struct uart_ops s3c24xx_serial_ops = {
- .pm = s3c24xx_serial_pm,
- .tx_empty = s3c24xx_serial_tx_empty,
- .get_mctrl = s3c24xx_serial_get_mctrl,
- .set_mctrl = s3c24xx_serial_set_mctrl,
- .stop_tx = s3c24xx_serial_stop_tx,
- .start_tx = s3c24xx_serial_start_tx,
- .stop_rx = s3c24xx_serial_stop_rx,
- .enable_ms = s3c24xx_serial_enable_ms,
- .break_ctl = s3c24xx_serial_break_ctl,
- .startup = s3c24xx_serial_startup,
- .shutdown = s3c24xx_serial_shutdown,
- .set_termios = s3c24xx_serial_set_termios,
- .type = s3c24xx_serial_type,
- .release_port = s3c24xx_serial_release_port,
- .request_port = s3c24xx_serial_request_port,
- .config_port = s3c24xx_serial_config_port,
- .verify_port = s3c24xx_serial_verify_port,
-};
-
-
-static struct uart_driver s3c24xx_uart_drv = {
- .owner = THIS_MODULE,
- .dev_name = "s3c2410_serial",
- .nr = 3,
- .cons = S3C24XX_SERIAL_CONSOLE,
- .driver_name = S3C24XX_SERIAL_NAME,
- .major = S3C24XX_SERIAL_MAJOR,
- .minor = S3C24XX_SERIAL_MINOR,
-};
-
-static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = {
- [0] = {
- .port = {
- .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock),
- .iotype = UPIO_MEM,
- .irq = IRQ_S3CUART_RX0,
- .uartclk = 0,
- .fifosize = 16,
- .ops = &s3c24xx_serial_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- }
- },
- [1] = {
- .port = {
- .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock),
- .iotype = UPIO_MEM,
- .irq = IRQ_S3CUART_RX1,
- .uartclk = 0,
- .fifosize = 16,
- .ops = &s3c24xx_serial_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- }
- },
-#if NR_PORTS > 2
-
- [2] = {
- .port = {
- .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock),
- .iotype = UPIO_MEM,
- .irq = IRQ_S3CUART_RX2,
- .uartclk = 0,
- .fifosize = 16,
- .ops = &s3c24xx_serial_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- }
- }
-#endif
-};
-
-/* s3c24xx_serial_resetport
- *
- * wrapper to call the specific reset for this port (reset the fifos
- * and the settings)
-*/
-
-static inline int s3c24xx_serial_resetport(struct uart_port * port,
- struct s3c2410_uartcfg *cfg)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
-
- return (info->reset_port)(port, cfg);
-}
-
-/* s3c24xx_serial_init_port
- *
- * initialise a single serial port from the platform device given
- */
-
-static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
- struct s3c24xx_uart_info *info,
- struct platform_device *platdev)
-{
- struct uart_port *port = &ourport->port;
- struct s3c2410_uartcfg *cfg;
- struct resource *res;
- int ret;
-
- dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev);
-
- if (platdev == NULL)
- return -ENODEV;
-
- cfg = s3c24xx_dev_to_cfg(&platdev->dev);
-
- if (port->mapbase != 0)
- return 0;
-
- if (cfg->hwport > 3)
- return -EINVAL;
-
- /* setup info for port */
- port->dev = &platdev->dev;
- ourport->info = info;
-
- /* copy the info in from provided structure */
- ourport->port.fifosize = info->fifosize;
-
- dbg("s3c24xx_serial_init_port: %p (hw %d)...\n", port, cfg->hwport);
-
- port->uartclk = 1;
-
- if (cfg->uart_flags & UPF_CONS_FLOW) {
- dbg("s3c24xx_serial_init_port: enabling flow control\n");
- port->flags |= UPF_CONS_FLOW;
- }
-
- /* sort our the physical and virtual addresses for each UART */
-
- res = platform_get_resource(platdev, IORESOURCE_MEM, 0);
- if (res == NULL) {
- printk(KERN_ERR "failed to find memory resource for uart\n");
- return -EINVAL;
- }
-
- dbg("resource %p (%lx..%lx)\n", res, res->start, res->end);
-
- port->mapbase = res->start;
- port->membase = S3C24XX_VA_UART + (res->start - S3C24XX_PA_UART);
- ret = platform_get_irq(platdev, 0);
- if (ret < 0)
- port->irq = 0;
- else
- port->irq = ret;
-
- ourport->clk = clk_get(&platdev->dev, "uart");
-
- dbg("port: map=%08x, mem=%08x, irq=%d, clock=%ld\n",
- port->mapbase, port->membase, port->irq, port->uartclk);
-
- /* reset the fifos (and setup the uart) */
- s3c24xx_serial_resetport(port, cfg);
- return 0;
-}
-
-static ssize_t s3c24xx_serial_show_clksrc(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct uart_port *port = s3c24xx_dev_to_port(dev);
- struct s3c24xx_uart_port *ourport = to_ourport(port);
-
- return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->clksrc->name);
-}
-
-static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
-
-/* Device driver serial port probe */
-
-static int probe_index = 0;
-
-static int s3c24xx_serial_probe(struct platform_device *dev,
- struct s3c24xx_uart_info *info)
-{
- struct s3c24xx_uart_port *ourport;
- int ret;
-
- dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index);
-
- ourport = &s3c24xx_serial_ports[probe_index];
- probe_index++;
-
- dbg("%s: initialising port %p...\n", __func__, ourport);
-
- ret = s3c24xx_serial_init_port(ourport, info, dev);
- if (ret < 0)
- goto probe_err;
-
- dbg("%s: adding port\n", __func__);
- uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
- platform_set_drvdata(dev, &ourport->port);
-
- ret = device_create_file(&dev->dev, &dev_attr_clock_source);
- if (ret < 0) {
- printk(KERN_ERR "%s: failed to add clksrc attr.\n", __func__);
- }
-
- return 0;
-
- probe_err:
- return ret;
-}
-
-static int s3c24xx_serial_remove(struct platform_device *dev)
-{
- struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
-
- if (port) {
- device_remove_file(&dev->dev, &dev_attr_clock_source);
- uart_remove_one_port(&s3c24xx_uart_drv, port);
- }
-
- return 0;
-}
-
-/* UART power management code */
-
-#ifdef CONFIG_PM
-
-static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t state)
-{
- struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
-
- if (port)
- uart_suspend_port(&s3c24xx_uart_drv, port);
-
- return 0;
-}
-
-static int s3c24xx_serial_resume(struct platform_device *dev)
-{
- struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
- struct s3c24xx_uart_port *ourport = to_ourport(port);
-
- if (port) {
- clk_enable(ourport->clk);
- s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port));
- clk_disable(ourport->clk);
-
- uart_resume_port(&s3c24xx_uart_drv, port);
- }
-
- return 0;
-}
-
-#else
-#define s3c24xx_serial_suspend NULL
-#define s3c24xx_serial_resume NULL
-#endif
-
-static int s3c24xx_serial_init(struct platform_driver *drv,
- struct s3c24xx_uart_info *info)
-{
- dbg("s3c24xx_serial_init(%p,%p)\n", drv, info);
- return platform_driver_register(drv);
-}
-
-
-/* now comes the code to initialise either the s3c2410 or s3c2440 serial
- * port information
-*/
-
-/* cpu specific variations on the serial port support */
-
-#ifdef CONFIG_CPU_S3C2400
-
-static int s3c2400_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- clk->divisor = 1;
- clk->name = "pclk";
-
- return 0;
-}
-
-static int s3c2400_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- return 0;
-}
-
-static int s3c2400_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- wr_regl(port, S3C2410_UCON, cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2400_uart_inf = {
- .name = "Samsung S3C2400 UART",
- .type = PORT_S3C2400,
- .fifosize = 16,
- .rx_fifomask = S3C2410_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2410_UFSTAT_RXFULL,
- .tx_fifofull = S3C2410_UFSTAT_TXFULL,
- .tx_fifomask = S3C2410_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2400_serial_getsource,
- .set_clksrc = s3c2400_serial_setsource,
- .reset_port = s3c2400_serial_resetport,
-};
-
-static int s3c2400_serial_probe(struct platform_device *dev)
-{
- return s3c24xx_serial_probe(dev, &s3c2400_uart_inf);
-}
-
-static struct platform_driver s3c2400_serial_drv = {
- .probe = s3c2400_serial_probe,
- .remove = s3c24xx_serial_remove,
- .suspend = s3c24xx_serial_suspend,
- .resume = s3c24xx_serial_resume,
- .driver = {
- .name = "s3c2400-uart",
- .owner = THIS_MODULE,
- },
-};
-
-static inline int s3c2400_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf);
-}
-
-static inline void s3c2400_serial_exit(void)
-{
- platform_driver_unregister(&s3c2400_serial_drv);
-}
-
-#define s3c2400_uart_inf_at &s3c2400_uart_inf
-#else
-
-static inline int s3c2400_serial_init(void)
-{
- return 0;
-}
-
-static inline void s3c2400_serial_exit(void)
-{
-}
-
-#define s3c2400_uart_inf_at NULL
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
-#endif /* CONFIG_CPU_S3C2400 */
+#include <asm/irq.h>
+#include <asm/hardware.h>
-/* S3C2410 support */
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
-#ifdef CONFIG_CPU_S3C2410
+#include "samsung.h"
static int s3c2410_serial_setsource(struct uart_port *port,
struct s3c24xx_uart_clksrc *clk)
.reset_port = s3c2410_serial_resetport,
};
-/* device management */
-
static int s3c2410_serial_probe(struct platform_device *dev)
{
return s3c24xx_serial_probe(dev, &s3c2410_uart_inf);
static struct platform_driver s3c2410_serial_drv = {
.probe = s3c2410_serial_probe,
.remove = s3c24xx_serial_remove,
- .suspend = s3c24xx_serial_suspend,
- .resume = s3c24xx_serial_resume,
.driver = {
.name = "s3c2410-uart",
.owner = THIS_MODULE,
},
};
-static inline int s3c2410_serial_init(void)
+s3c24xx_console_init(&s3c2410_serial_drv, &s3c2410_uart_inf);
+
+static int __init s3c2410_serial_init(void)
{
return s3c24xx_serial_init(&s3c2410_serial_drv, &s3c2410_uart_inf);
}
-static inline void s3c2410_serial_exit(void)
+static void __exit s3c2410_serial_exit(void)
{
platform_driver_unregister(&s3c2410_serial_drv);
}
-#define s3c2410_uart_inf_at &s3c2410_uart_inf
-#else
-
-static inline int s3c2410_serial_init(void)
-{
- return 0;
-}
-
-static inline void s3c2410_serial_exit(void)
-{
-}
-
-#define s3c2410_uart_inf_at NULL
-
-#endif /* CONFIG_CPU_S3C2410 */
-
-#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442)
-
-static int s3c2440_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- // todo - proper fclk<>nonfclk switch //
-
- ucon &= ~S3C2440_UCON_CLKMASK;
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2440_UCON_UCLK;
- else if (strcmp(clk->name, "pclk") == 0)
- ucon |= S3C2440_UCON_PCLK;
- else if (strcmp(clk->name, "fclk") == 0)
- ucon |= S3C2440_UCON_FCLK;
- else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s3c2440_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
- unsigned long ucon0, ucon1, ucon2;
-
- switch (ucon & S3C2440_UCON_CLKMASK) {
- case S3C2440_UCON_UCLK:
- clk->divisor = 1;
- clk->name = "uclk";
- break;
-
- case S3C2440_UCON_PCLK:
- case S3C2440_UCON_PCLK2:
- clk->divisor = 1;
- clk->name = "pclk";
- break;
-
- case S3C2440_UCON_FCLK:
- /* the fun of calculating the uart divisors on
- * the s3c2440 */
-
- ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON);
- ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON);
- ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON);
-
- printk("ucons: %08lx, %08lx, %08lx\n", ucon0, ucon1, ucon2);
-
- ucon0 &= S3C2440_UCON0_DIVMASK;
- ucon1 &= S3C2440_UCON1_DIVMASK;
- ucon2 &= S3C2440_UCON2_DIVMASK;
-
- if (ucon0 != 0) {
- clk->divisor = ucon0 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 6;
- } else if (ucon1 != 0) {
- clk->divisor = ucon1 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 21;
- } else if (ucon2 != 0) {
- clk->divisor = ucon2 >> S3C2440_UCON_DIVSHIFT;
- clk->divisor += 36;
- } else {
- /* manual calims 44, seems to be 9 */
- clk->divisor = 9;
- }
-
- clk->name = "fclk";
- break;
- }
-
- return 0;
-}
-
-static int s3c2440_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- dbg("s3c2440_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- /* ensure we don't change the clock settings... */
-
- ucon &= (S3C2440_UCON0_DIVMASK | (3<<10));
-
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2440_uart_inf = {
- .name = "Samsung S3C2440 UART",
- .type = PORT_S3C2440,
- .fifosize = 64,
- .rx_fifomask = S3C2440_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2440_UFSTAT_RXFULL,
- .tx_fifofull = S3C2440_UFSTAT_TXFULL,
- .tx_fifomask = S3C2440_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2440_serial_getsource,
- .set_clksrc = s3c2440_serial_setsource,
- .reset_port = s3c2440_serial_resetport,
-};
-
-/* device management */
-
-static int s3c2440_serial_probe(struct platform_device *dev)
-{
- dbg("s3c2440_serial_probe: dev=%p\n", dev);
- return s3c24xx_serial_probe(dev, &s3c2440_uart_inf);
-}
-
-static struct platform_driver s3c2440_serial_drv = {
- .probe = s3c2440_serial_probe,
- .remove = s3c24xx_serial_remove,
- .suspend = s3c24xx_serial_suspend,
- .resume = s3c24xx_serial_resume,
- .driver = {
- .name = "s3c2440-uart",
- .owner = THIS_MODULE,
- },
-};
-
-
-static inline int s3c2440_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf);
-}
-
-static inline void s3c2440_serial_exit(void)
-{
- platform_driver_unregister(&s3c2440_serial_drv);
-}
-
-#define s3c2440_uart_inf_at &s3c2440_uart_inf
-#else
-
-static inline int s3c2440_serial_init(void)
-{
- return 0;
-}
-
-static inline void s3c2440_serial_exit(void)
-{
-}
-
-#define s3c2440_uart_inf_at NULL
-#endif /* CONFIG_CPU_S3C2440 */
-
-#if defined(CONFIG_CPU_S3C2412)
-
-static int s3c2412_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- ucon &= ~S3C2412_UCON_CLKMASK;
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2440_UCON_UCLK;
- else if (strcmp(clk->name, "pclk") == 0)
- ucon |= S3C2440_UCON_PCLK;
- else if (strcmp(clk->name, "usysclk") == 0)
- ucon |= S3C2412_UCON_USYSCLK;
- else {
- printk(KERN_ERR "unknown clock source %s\n", clk->name);
- return -EINVAL;
- }
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-
-static int s3c2412_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- switch (ucon & S3C2412_UCON_CLKMASK) {
- case S3C2412_UCON_UCLK:
- clk->divisor = 1;
- clk->name = "uclk";
- break;
-
- case S3C2412_UCON_PCLK:
- case S3C2412_UCON_PCLK2:
- clk->divisor = 1;
- clk->name = "pclk";
- break;
-
- case S3C2412_UCON_USYSCLK:
- clk->divisor = 1;
- clk->name = "usysclk";
- break;
- }
-
- return 0;
-}
-
-static int s3c2412_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- dbg("%s: port=%p (%08lx), cfg=%p\n",
- __func__, port, port->mapbase, cfg);
-
- /* ensure we don't change the clock settings... */
-
- ucon &= S3C2412_UCON_CLKMASK;
-
- wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2412_uart_inf = {
- .name = "Samsung S3C2412 UART",
- .type = PORT_S3C2412,
- .fifosize = 64,
- .rx_fifomask = S3C2440_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2440_UFSTAT_RXFULL,
- .tx_fifofull = S3C2440_UFSTAT_TXFULL,
- .tx_fifomask = S3C2440_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2412_serial_getsource,
- .set_clksrc = s3c2412_serial_setsource,
- .reset_port = s3c2412_serial_resetport,
-};
-
-/* device management */
-
-static int s3c2412_serial_probe(struct platform_device *dev)
-{
- dbg("s3c2440_serial_probe: dev=%p\n", dev);
- return s3c24xx_serial_probe(dev, &s3c2412_uart_inf);
-}
-
-static struct platform_driver s3c2412_serial_drv = {
- .probe = s3c2412_serial_probe,
- .remove = s3c24xx_serial_remove,
- .suspend = s3c24xx_serial_suspend,
- .resume = s3c24xx_serial_resume,
- .driver = {
- .name = "s3c2412-uart",
- .owner = THIS_MODULE,
- },
-};
-
-
-static inline int s3c2412_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf);
-}
-
-static inline void s3c2412_serial_exit(void)
-{
- platform_driver_unregister(&s3c2412_serial_drv);
-}
-
-#define s3c2412_uart_inf_at &s3c2412_uart_inf
-#else
-
-static inline int s3c2412_serial_init(void)
-{
- return 0;
-}
-
-static inline void s3c2412_serial_exit(void)
-{
-}
-
-#define s3c2412_uart_inf_at NULL
-#endif /* CONFIG_CPU_S3C2440 */
-
-
-/* module initialisation code */
-
-static int __init s3c24xx_serial_modinit(void)
-{
- int ret;
-
- ret = uart_register_driver(&s3c24xx_uart_drv);
- if (ret < 0) {
- printk(KERN_ERR "failed to register UART driver\n");
- return -1;
- }
-
- s3c2400_serial_init();
- s3c2410_serial_init();
- s3c2412_serial_init();
- s3c2440_serial_init();
-
- return 0;
-}
-
-static void __exit s3c24xx_serial_modexit(void)
-{
- s3c2400_serial_exit();
- s3c2410_serial_exit();
- s3c2412_serial_exit();
- s3c2440_serial_exit();
-
- uart_unregister_driver(&s3c24xx_uart_drv);
-}
-
-
-module_init(s3c24xx_serial_modinit);
-module_exit(s3c24xx_serial_modexit);
-
-/* Console code */
-
-#ifdef CONFIG_SERIAL_S3C2410_CONSOLE
-
-static struct uart_port *cons_uart;
-
-static int
-s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
-{
- struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned long ufstat, utrstat;
-
- if (ufcon & S3C2410_UFCON_FIFOMODE) {
- /* fifo mode - check ammount of data in fifo registers... */
-
- ufstat = rd_regl(port, S3C2410_UFSTAT);
- return (ufstat & info->tx_fifofull) ? 0 : 1;
- }
-
- /* in non-fifo mode, we go and use the tx buffer empty */
-
- utrstat = rd_regl(port, S3C2410_UTRSTAT);
- return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0;
-}
-
-static void
-s3c24xx_serial_console_putchar(struct uart_port *port, int ch)
-{
- unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON);
- while (!s3c24xx_serial_console_txrdy(port, ufcon))
- barrier();
- wr_regb(cons_uart, S3C2410_UTXH, ch);
-}
-
-static void
-s3c24xx_serial_console_write(struct console *co, const char *s,
- unsigned int count)
-{
- uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar);
-}
-
-static void __init
-s3c24xx_serial_get_options(struct uart_port *port, int *baud,
- int *parity, int *bits)
-{
- struct s3c24xx_uart_clksrc clksrc;
- struct clk *clk;
- unsigned int ulcon;
- unsigned int ucon;
- unsigned int ubrdiv;
- unsigned long rate;
-
- ulcon = rd_regl(port, S3C2410_ULCON);
- ucon = rd_regl(port, S3C2410_UCON);
- ubrdiv = rd_regl(port, S3C2410_UBRDIV);
-
- dbg("s3c24xx_serial_get_options: port=%p\n"
- "registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n",
- port, ulcon, ucon, ubrdiv);
-
- if ((ucon & 0xf) != 0) {
- /* consider the serial port configured if the tx/rx mode set */
-
- switch (ulcon & S3C2410_LCON_CSMASK) {
- case S3C2410_LCON_CS5:
- *bits = 5;
- break;
- case S3C2410_LCON_CS6:
- *bits = 6;
- break;
- case S3C2410_LCON_CS7:
- *bits = 7;
- break;
- default:
- case S3C2410_LCON_CS8:
- *bits = 8;
- break;
- }
-
- switch (ulcon & S3C2410_LCON_PMASK) {
- case S3C2410_LCON_PEVEN:
- *parity = 'e';
- break;
-
- case S3C2410_LCON_PODD:
- *parity = 'o';
- break;
-
- case S3C2410_LCON_PNONE:
- default:
- *parity = 'n';
- }
-
- /* now calculate the baud rate */
-
- s3c24xx_serial_getsource(port, &clksrc);
-
- clk = clk_get(port->dev, clksrc.name);
- if (!IS_ERR(clk) && clk != NULL)
- rate = clk_get_rate(clk) / clksrc.divisor;
- else
- rate = 1;
-
-
- *baud = rate / ( 16 * (ubrdiv + 1));
- dbg("calculated baud %d\n", *baud);
- }
-
-}
-
-/* s3c24xx_serial_init_ports
- *
- * initialise the serial ports from the machine provided initialisation
- * data.
-*/
-
-static int s3c24xx_serial_init_ports(struct s3c24xx_uart_info *info)
-{
- struct s3c24xx_uart_port *ptr = s3c24xx_serial_ports;
- struct platform_device **platdev_ptr;
- int i;
-
- dbg("s3c24xx_serial_init_ports: initialising ports...\n");
-
- platdev_ptr = s3c24xx_uart_devs;
-
- for (i = 0; i < NR_PORTS; i++, ptr++, platdev_ptr++) {
- s3c24xx_serial_init_port(ptr, info, *platdev_ptr);
- }
-
- return 0;
-}
-
-static int __init
-s3c24xx_serial_console_setup(struct console *co, char *options)
-{
- struct uart_port *port;
- int baud = 9600;
- int bits = 8;
- int parity = 'n';
- int flow = 'n';
-
- dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n",
- co, co->index, options);
-
- /* is this a valid port */
-
- if (co->index == -1 || co->index >= NR_PORTS)
- co->index = 0;
-
- port = &s3c24xx_serial_ports[co->index].port;
-
- /* is the port configured? */
-
- if (port->mapbase == 0x0) {
- co->index = 0;
- port = &s3c24xx_serial_ports[co->index].port;
- }
-
- cons_uart = port;
-
- dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index);
-
- /*
- * Check whether an invalid uart number has been specified, and
- * if so, search for the first available port that does have
- * console support.
- */
- if (options)
- uart_parse_options(options, &baud, &parity, &bits, &flow);
- else
- s3c24xx_serial_get_options(port, &baud, &parity, &bits);
-
- dbg("s3c24xx_serial_console_setup: baud %d\n", baud);
-
- return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-/* s3c24xx_serial_initconsole
- *
- * initialise the console from one of the uart drivers
-*/
-
-static struct console s3c24xx_serial_console =
-{
- .name = S3C24XX_SERIAL_NAME,
- .device = uart_console_device,
- .flags = CON_PRINTBUFFER,
- .index = -1,
- .write = s3c24xx_serial_console_write,
- .setup = s3c24xx_serial_console_setup
-};
-
-static int s3c24xx_serial_initconsole(void)
-{
- struct s3c24xx_uart_info *info;
- struct platform_device *dev = s3c24xx_uart_devs[0];
-
- dbg("s3c24xx_serial_initconsole\n");
-
- /* select driver based on the cpu */
-
- if (dev == NULL) {
- printk(KERN_ERR "s3c24xx: no devices for console init\n");
- return 0;
- }
-
- if (strcmp(dev->name, "s3c2400-uart") == 0) {
- info = s3c2400_uart_inf_at;
- } else if (strcmp(dev->name, "s3c2410-uart") == 0) {
- info = s3c2410_uart_inf_at;
- } else if (strcmp(dev->name, "s3c2440-uart") == 0) {
- info = s3c2440_uart_inf_at;
- } else if (strcmp(dev->name, "s3c2412-uart") == 0) {
- info = s3c2412_uart_inf_at;
- } else {
- printk(KERN_ERR "s3c24xx: no driver for %s\n", dev->name);
- return 0;
- }
-
- if (info == NULL) {
- printk(KERN_ERR "s3c24xx: no driver for console\n");
- return 0;
- }
-
- s3c24xx_serial_console.data = &s3c24xx_uart_drv;
- s3c24xx_serial_init_ports(info);
-
- register_console(&s3c24xx_serial_console);
- return 0;
-}
-
-console_initcall(s3c24xx_serial_initconsole);
-
-#endif /* CONFIG_SERIAL_S3C2410_CONSOLE */
+module_init(s3c2410_serial_init);
+module_exit(s3c2410_serial_exit);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_DESCRIPTION("Samsung S3C2410/S3C2440/S3C2412 Serial port driver");
-MODULE_ALIAS("platform:s3c2400-uart");
+MODULE_DESCRIPTION("Samsung S3C2410 SoC Serial port driver");
MODULE_ALIAS("platform:s3c2410-uart");
-MODULE_ALIAS("platform:s3c2412-uart");
-MODULE_ALIAS("platform:s3c2440-uart");
--- /dev/null
+/* linux/drivers/serial/s3c2412.c
+ *
+ * Driver for Samsung S3C2412 and S3C2413 SoC onboard UARTs.
+ *
+ * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+
+#include <asm/irq.h>
+#include <asm/hardware.h>
+
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+
+#include "samsung.h"
+
+static int s3c2412_serial_setsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+
+ ucon &= ~S3C2412_UCON_CLKMASK;
+
+ if (strcmp(clk->name, "uclk") == 0)
+ ucon |= S3C2440_UCON_UCLK;
+ else if (strcmp(clk->name, "pclk") == 0)
+ ucon |= S3C2440_UCON_PCLK;
+ else if (strcmp(clk->name, "usysclk") == 0)
+ ucon |= S3C2412_UCON_USYSCLK;
+ else {
+ printk(KERN_ERR "unknown clock source %s\n", clk->name);
+ return -EINVAL;
+ }
+
+ wr_regl(port, S3C2410_UCON, ucon);
+ return 0;
+}
+
+
+static int s3c2412_serial_getsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+
+ switch (ucon & S3C2412_UCON_CLKMASK) {
+ case S3C2412_UCON_UCLK:
+ clk->divisor = 1;
+ clk->name = "uclk";
+ break;
+
+ case S3C2412_UCON_PCLK:
+ case S3C2412_UCON_PCLK2:
+ clk->divisor = 1;
+ clk->name = "pclk";
+ break;
+
+ case S3C2412_UCON_USYSCLK:
+ clk->divisor = 1;
+ clk->name = "usysclk";
+ break;
+ }
+
+ return 0;
+}
+
+static int s3c2412_serial_resetport(struct uart_port *port,
+ struct s3c2410_uartcfg *cfg)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+
+ dbg("%s: port=%p (%08lx), cfg=%p\n",
+ __func__, port, port->mapbase, cfg);
+
+ /* ensure we don't change the clock settings... */
+
+ ucon &= S3C2412_UCON_CLKMASK;
+
+ wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
+ wr_regl(port, S3C2410_ULCON, cfg->ulcon);
+
+ /* reset both fifos */
+
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon);
+
+ return 0;
+}
+
+static struct s3c24xx_uart_info s3c2412_uart_inf = {
+ .name = "Samsung S3C2412 UART",
+ .type = PORT_S3C2412,
+ .fifosize = 64,
+ .rx_fifomask = S3C2440_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2440_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2440_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2440_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
+ .get_clksrc = s3c2412_serial_getsource,
+ .set_clksrc = s3c2412_serial_setsource,
+ .reset_port = s3c2412_serial_resetport,
+};
+
+/* device management */
+
+static int s3c2412_serial_probe(struct platform_device *dev)
+{
+ dbg("s3c2440_serial_probe: dev=%p\n", dev);
+ return s3c24xx_serial_probe(dev, &s3c2412_uart_inf);
+}
+
+static struct platform_driver s3c2412_serial_drv = {
+ .probe = s3c2412_serial_probe,
+ .remove = s3c24xx_serial_remove,
+ .driver = {
+ .name = "s3c2412-uart",
+ .owner = THIS_MODULE,
+ },
+};
+
+s3c24xx_console_init(&s3c2412_serial_drv, &s3c2412_uart_inf);
+
+static inline int s3c2412_serial_init(void)
+{
+ return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf);
+}
+
+static inline void s3c2412_serial_exit(void)
+{
+ platform_driver_unregister(&s3c2412_serial_drv);
+}
+
+module_init(s3c2412_serial_init);
+module_exit(s3c2412_serial_exit);
+
+MODULE_DESCRIPTION("Samsung S3C2412,S3C2413 SoC Serial port driver");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:s3c2412-uart");
--- /dev/null
+/* linux/drivers/serial/s3c2440.c
+ *
+ * Driver for Samsung S3C2440 and S3C2442 SoC onboard UARTs.
+ *
+ * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+
+#include <asm/irq.h>
+#include <asm/hardware.h>
+
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+
+#include "samsung.h"
+
+
+static int s3c2440_serial_setsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+
+ /* todo - proper fclk<>nonfclk switch. */
+
+ ucon &= ~S3C2440_UCON_CLKMASK;
+
+ if (strcmp(clk->name, "uclk") == 0)
+ ucon |= S3C2440_UCON_UCLK;
+ else if (strcmp(clk->name, "pclk") == 0)
+ ucon |= S3C2440_UCON_PCLK;
+ else if (strcmp(clk->name, "fclk") == 0)
+ ucon |= S3C2440_UCON_FCLK;
+ else {
+ printk(KERN_ERR "unknown clock source %s\n", clk->name);
+ return -EINVAL;
+ }
+
+ wr_regl(port, S3C2410_UCON, ucon);
+ return 0;
+}
+
+
+static int s3c2440_serial_getsource(struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clk)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+ unsigned long ucon0, ucon1, ucon2;
+
+ switch (ucon & S3C2440_UCON_CLKMASK) {
+ case S3C2440_UCON_UCLK:
+ clk->divisor = 1;
+ clk->name = "uclk";
+ break;
+
+ case S3C2440_UCON_PCLK:
+ case S3C2440_UCON_PCLK2:
+ clk->divisor = 1;
+ clk->name = "pclk";
+ break;
+
+ case S3C2440_UCON_FCLK:
+ /* the fun of calculating the uart divisors on
+ * the s3c2440 */
+
+ ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON);
+ ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON);
+ ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON);
+
+ printk("ucons: %08lx, %08lx, %08lx\n", ucon0, ucon1, ucon2);
+
+ ucon0 &= S3C2440_UCON0_DIVMASK;
+ ucon1 &= S3C2440_UCON1_DIVMASK;
+ ucon2 &= S3C2440_UCON2_DIVMASK;
+
+ if (ucon0 != 0) {
+ clk->divisor = ucon0 >> S3C2440_UCON_DIVSHIFT;
+ clk->divisor += 6;
+ } else if (ucon1 != 0) {
+ clk->divisor = ucon1 >> S3C2440_UCON_DIVSHIFT;
+ clk->divisor += 21;
+ } else if (ucon2 != 0) {
+ clk->divisor = ucon2 >> S3C2440_UCON_DIVSHIFT;
+ clk->divisor += 36;
+ } else {
+ /* manual calims 44, seems to be 9 */
+ clk->divisor = 9;
+ }
+
+ clk->name = "fclk";
+ break;
+ }
+
+ return 0;
+}
+
+static int s3c2440_serial_resetport(struct uart_port *port,
+ struct s3c2410_uartcfg *cfg)
+{
+ unsigned long ucon = rd_regl(port, S3C2410_UCON);
+
+ dbg("s3c2440_serial_resetport: port=%p (%08lx), cfg=%p\n",
+ port, port->mapbase, cfg);
+
+ /* ensure we don't change the clock settings... */
+
+ ucon &= (S3C2440_UCON0_DIVMASK | (3<<10));
+
+ wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
+ wr_regl(port, S3C2410_ULCON, cfg->ulcon);
+
+ /* reset both fifos */
+
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
+ wr_regl(port, S3C2410_UFCON, cfg->ufcon);
+
+ return 0;
+}
+
+static struct s3c24xx_uart_info s3c2440_uart_inf = {
+ .name = "Samsung S3C2440 UART",
+ .type = PORT_S3C2440,
+ .fifosize = 64,
+ .rx_fifomask = S3C2440_UFSTAT_RXMASK,
+ .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
+ .rx_fifofull = S3C2440_UFSTAT_RXFULL,
+ .tx_fifofull = S3C2440_UFSTAT_TXFULL,
+ .tx_fifomask = S3C2440_UFSTAT_TXMASK,
+ .tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
+ .get_clksrc = s3c2440_serial_getsource,
+ .set_clksrc = s3c2440_serial_setsource,
+ .reset_port = s3c2440_serial_resetport,
+};
+
+/* device management */
+
+static int s3c2440_serial_probe(struct platform_device *dev)
+{
+ dbg("s3c2440_serial_probe: dev=%p\n", dev);
+ return s3c24xx_serial_probe(dev, &s3c2440_uart_inf);
+}
+
+static struct platform_driver s3c2440_serial_drv = {
+ .probe = s3c2440_serial_probe,
+ .remove = s3c24xx_serial_remove,
+ .driver = {
+ .name = "s3c2440-uart",
+ .owner = THIS_MODULE,
+ },
+};
+
+s3c24xx_console_init(&s3c2440_serial_drv, &s3c2440_uart_inf);
+
+static int __init s3c2440_serial_init(void)
+{
+ return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf);
+}
+
+static void __exit s3c2440_serial_exit(void)
+{
+ platform_driver_unregister(&s3c2440_serial_drv);
+}
+
+module_init(s3c2440_serial_init);
+module_exit(s3c2440_serial_exit);
+
+MODULE_DESCRIPTION("Samsung S3C2440,S3C2442 SoC Serial port driver");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_LICENSE("GPLi v2");
+MODULE_ALIAS("platform:s3c2440-uart");
--- /dev/null
+/* linux/drivers/serial/samsuing.c
+ *
+ * Driver core for Samsung SoC onboard UARTs.
+ *
+ * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* Hote on 2410 error handling
+ *
+ * The s3c2410 manual has a love/hate affair with the contents of the
+ * UERSTAT register in the UART blocks, and keeps marking some of the
+ * error bits as reserved. Having checked with the s3c2410x01,
+ * it copes with BREAKs properly, so I am happy to ignore the RESERVED
+ * feature from the latter versions of the manual.
+ *
+ * If it becomes aparrent that latter versions of the 2410 remove these
+ * bits, then action will have to be taken to differentiate the versions
+ * and change the policy on BREAK
+ *
+ * BJD, 04-Nov-2004
+*/
+
+#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/sysrq.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include <asm/irq.h>
+
+#include <asm/hardware.h>
+
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/arch/regs-gpio.h>
+
+#include "samsung.h"
+
+/* UART name and device definitions */
+
+#define S3C24XX_SERIAL_NAME "ttySAC"
+#define S3C24XX_SERIAL_MAJOR 204
+#define S3C24XX_SERIAL_MINOR 64
+
+/* we can support 3 uarts, but not always use them */
+
+#ifdef CONFIG_CPU_S3C2400
+#define NR_PORTS (2)
+#else
+#define NR_PORTS (3)
+#endif
+
+/* port irq numbers */
+
+#define TX_IRQ(port) ((port)->irq + 1)
+#define RX_IRQ(port) ((port)->irq)
+
+/* macros to change one thing to another */
+
+#define tx_enabled(port) ((port)->unused[0])
+#define rx_enabled(port) ((port)->unused[1])
+
+/* flag to ignore all characters comming in */
+#define RXSTAT_DUMMY_READ (0x10000000)
+
+static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port)
+{
+ return container_of(port, struct s3c24xx_uart_port, port);
+}
+
+/* translate a port to the device name */
+
+static inline const char *s3c24xx_serial_portname(struct uart_port *port)
+{
+ return to_platform_device(port->dev)->name;
+}
+
+static int s3c24xx_serial_txempty_nofifo(struct uart_port *port)
+{
+ return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE);
+}
+
+static void s3c24xx_serial_rx_enable(struct uart_port *port)
+{
+ unsigned long flags;
+ unsigned int ucon, ufcon;
+ int count = 10000;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ while (--count && !s3c24xx_serial_txempty_nofifo(port))
+ udelay(100);
+
+ ufcon = rd_regl(port, S3C2410_UFCON);
+ ufcon |= S3C2410_UFCON_RESETRX;
+ wr_regl(port, S3C2410_UFCON, ufcon);
+
+ ucon = rd_regl(port, S3C2410_UCON);
+ ucon |= S3C2410_UCON_RXIRQMODE;
+ wr_regl(port, S3C2410_UCON, ucon);
+
+ rx_enabled(port) = 1;
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void s3c24xx_serial_rx_disable(struct uart_port *port)
+{
+ unsigned long flags;
+ unsigned int ucon;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ ucon = rd_regl(port, S3C2410_UCON);
+ ucon &= ~S3C2410_UCON_RXIRQMODE;
+ wr_regl(port, S3C2410_UCON, ucon);
+
+ rx_enabled(port) = 0;
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void s3c24xx_serial_stop_tx(struct uart_port *port)
+{
+ if (tx_enabled(port)) {
+ disable_irq(TX_IRQ(port));
+ tx_enabled(port) = 0;
+ if (port->flags & UPF_CONS_FLOW)
+ s3c24xx_serial_rx_enable(port);
+ }
+}
+
+static void s3c24xx_serial_start_tx(struct uart_port *port)
+{
+ if (!tx_enabled(port)) {
+ if (port->flags & UPF_CONS_FLOW)
+ s3c24xx_serial_rx_disable(port);
+
+ enable_irq(TX_IRQ(port));
+ tx_enabled(port) = 1;
+ }
+}
+
+
+static void s3c24xx_serial_stop_rx(struct uart_port *port)
+{
+ if (rx_enabled(port)) {
+ dbg("s3c24xx_serial_stop_rx: port=%p\n", port);
+ disable_irq(RX_IRQ(port));
+ rx_enabled(port) = 0;
+ }
+}
+
+static void s3c24xx_serial_enable_ms(struct uart_port *port)
+{
+}
+
+static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port)
+{
+ return to_ourport(port)->info;
+}
+
+static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port)
+{
+ if (port->dev == NULL)
+ return NULL;
+
+ return (struct s3c2410_uartcfg *)port->dev->platform_data;
+}
+
+static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport,
+ unsigned long ufstat)
+{
+ struct s3c24xx_uart_info *info = ourport->info;
+
+ if (ufstat & info->rx_fifofull)
+ return info->fifosize;
+
+ return (ufstat & info->rx_fifomask) >> info->rx_fifoshift;
+}
+
+
+/* ? - where has parity gone?? */
+#define S3C2410_UERSTAT_PARITY (0x1000)
+
+static irqreturn_t
+s3c24xx_serial_rx_chars(int irq, void *dev_id)
+{
+ struct s3c24xx_uart_port *ourport = dev_id;
+ struct uart_port *port = &ourport->port;
+ struct tty_struct *tty = port->info->tty;
+ unsigned int ufcon, ch, flag, ufstat, uerstat;
+ int max_count = 64;
+
+ while (max_count-- > 0) {
+ ufcon = rd_regl(port, S3C2410_UFCON);
+ ufstat = rd_regl(port, S3C2410_UFSTAT);
+
+ if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
+ break;
+
+ uerstat = rd_regl(port, S3C2410_UERSTAT);
+ ch = rd_regb(port, S3C2410_URXH);
+
+ if (port->flags & UPF_CONS_FLOW) {
+ int txe = s3c24xx_serial_txempty_nofifo(port);
+
+ if (rx_enabled(port)) {
+ if (!txe) {
+ rx_enabled(port) = 0;
+ continue;
+ }
+ } else {
+ if (txe) {
+ ufcon |= S3C2410_UFCON_RESETRX;
+ wr_regl(port, S3C2410_UFCON, ufcon);
+ rx_enabled(port) = 1;
+ goto out;
+ }
+ continue;
+ }
+ }
+
+ /* insert the character into the buffer */
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) {
+ dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n",
+ ch, uerstat);
+
+ /* check for break */
+ if (uerstat & S3C2410_UERSTAT_BREAK) {
+ dbg("break!\n");
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ goto ignore_char;
+ }
+
+ if (uerstat & S3C2410_UERSTAT_FRAME)
+ port->icount.frame++;
+ if (uerstat & S3C2410_UERSTAT_OVERRUN)
+ port->icount.overrun++;
+
+ uerstat &= port->read_status_mask;
+
+ if (uerstat & S3C2410_UERSTAT_BREAK)
+ flag = TTY_BREAK;
+ else if (uerstat & S3C2410_UERSTAT_PARITY)
+ flag = TTY_PARITY;
+ else if (uerstat & (S3C2410_UERSTAT_FRAME |
+ S3C2410_UERSTAT_OVERRUN))
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char(port, ch))
+ goto ignore_char;
+
+ uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN,
+ ch, flag);
+
+ ignore_char:
+ continue;
+ }
+ tty_flip_buffer_push(tty);
+
+ out:
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id)
+{
+ struct s3c24xx_uart_port *ourport = id;
+ struct uart_port *port = &ourport->port;
+ struct circ_buf *xmit = &port->info->xmit;
+ int count = 256;
+
+ if (port->x_char) {
+ wr_regb(port, S3C2410_UTXH, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ goto out;
+ }
+
+ /* if there isnt anything more to transmit, or the uart is now
+ * stopped, disable the uart and exit
+ */
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ s3c24xx_serial_stop_tx(port);
+ goto out;
+ }
+
+ /* try and drain the buffer... */
+
+ while (!uart_circ_empty(xmit) && count-- > 0) {
+ if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull)
+ break;
+
+ wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ s3c24xx_serial_stop_tx(port);
+
+ out:
+ return IRQ_HANDLED;
+}
+
+static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT);
+ unsigned long ufcon = rd_regl(port, S3C2410_UFCON);
+
+ if (ufcon & S3C2410_UFCON_FIFOMODE) {
+ if ((ufstat & info->tx_fifomask) != 0 ||
+ (ufstat & info->tx_fifofull))
+ return 0;
+
+ return 1;
+ }
+
+ return s3c24xx_serial_txempty_nofifo(port);
+}
+
+/* no modem control lines */
+static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
+{
+ unsigned int umstat = rd_regb(port, S3C2410_UMSTAT);
+
+ if (umstat & S3C2410_UMSTAT_CTS)
+ return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+ else
+ return TIOCM_CAR | TIOCM_DSR;
+}
+
+static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ /* todo - possibly remove AFC and do manual CTS */
+}
+
+static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
+{
+ unsigned long flags;
+ unsigned int ucon;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ ucon = rd_regl(port, S3C2410_UCON);
+
+ if (break_state)
+ ucon |= S3C2410_UCON_SBREAK;
+ else
+ ucon &= ~S3C2410_UCON_SBREAK;
+
+ wr_regl(port, S3C2410_UCON, ucon);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void s3c24xx_serial_shutdown(struct uart_port *port)
+{
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+
+ if (ourport->tx_claimed) {
+ free_irq(TX_IRQ(port), ourport);
+ tx_enabled(port) = 0;
+ ourport->tx_claimed = 0;
+ }
+
+ if (ourport->rx_claimed) {
+ free_irq(RX_IRQ(port), ourport);
+ ourport->rx_claimed = 0;
+ rx_enabled(port) = 0;
+ }
+}
+
+
+static int s3c24xx_serial_startup(struct uart_port *port)
+{
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+ int ret;
+
+ dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n",
+ port->mapbase, port->membase);
+
+ rx_enabled(port) = 1;
+
+ ret = request_irq(RX_IRQ(port),
+ s3c24xx_serial_rx_chars, 0,
+ s3c24xx_serial_portname(port), ourport);
+
+ if (ret != 0) {
+ printk(KERN_ERR "cannot get irq %d\n", RX_IRQ(port));
+ return ret;
+ }
+
+ ourport->rx_claimed = 1;
+
+ dbg("requesting tx irq...\n");
+
+ tx_enabled(port) = 1;
+
+ ret = request_irq(TX_IRQ(port),
+ s3c24xx_serial_tx_chars, 0,
+ s3c24xx_serial_portname(port), ourport);
+
+ if (ret) {
+ printk(KERN_ERR "cannot get irq %d\n", TX_IRQ(port));
+ goto err;
+ }
+
+ ourport->tx_claimed = 1;
+
+ dbg("s3c24xx_serial_startup ok\n");
+
+ /* the port reset code should have done the correct
+ * register setup for the port controls */
+
+ return ret;
+
+ err:
+ s3c24xx_serial_shutdown(port);
+ return ret;
+}
+
+/* power power management control */
+
+static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
+ unsigned int old)
+{
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+
+ switch (level) {
+ case 3:
+ if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+ clk_disable(ourport->baudclk);
+
+ clk_disable(ourport->clk);
+ break;
+
+ case 0:
+ clk_enable(ourport->clk);
+
+ if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+ clk_enable(ourport->baudclk);
+
+ break;
+ default:
+ printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level);
+ }
+}
+
+/* baud rate calculation
+ *
+ * The UARTs on the S3C2410/S3C2440 can take their clocks from a number
+ * of different sources, including the peripheral clock ("pclk") and an
+ * external clock ("uclk"). The S3C2440 also adds the core clock ("fclk")
+ * with a programmable extra divisor.
+ *
+ * The following code goes through the clock sources, and calculates the
+ * baud clocks (and the resultant actual baud rates) and then tries to
+ * pick the closest one and select that.
+ *
+*/
+
+
+#define MAX_CLKS (8)
+
+static struct s3c24xx_uart_clksrc tmp_clksrc = {
+ .name = "pclk",
+ .min_baud = 0,
+ .max_baud = 0,
+ .divisor = 1,
+};
+
+static inline int
+s3c24xx_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+
+ return (info->get_clksrc)(port, c);
+}
+
+static inline int
+s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+
+ return (info->set_clksrc)(port, c);
+}
+
+struct baud_calc {
+ struct s3c24xx_uart_clksrc *clksrc;
+ unsigned int calc;
+ unsigned int quot;
+ struct clk *src;
+};
+
+static int s3c24xx_serial_calcbaud(struct baud_calc *calc,
+ struct uart_port *port,
+ struct s3c24xx_uart_clksrc *clksrc,
+ unsigned int baud)
+{
+ unsigned long rate;
+
+ calc->src = clk_get(port->dev, clksrc->name);
+ if (calc->src == NULL || IS_ERR(calc->src))
+ return 0;
+
+ rate = clk_get_rate(calc->src);
+ rate /= clksrc->divisor;
+
+ calc->clksrc = clksrc;
+ calc->quot = (rate + (8 * baud)) / (16 * baud);
+ calc->calc = (rate / (calc->quot * 16));
+
+ calc->quot--;
+ return 1;
+}
+
+static unsigned int s3c24xx_serial_getclk(struct uart_port *port,
+ struct s3c24xx_uart_clksrc **clksrc,
+ struct clk **clk,
+ unsigned int baud)
+{
+ struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
+ struct s3c24xx_uart_clksrc *clkp;
+ struct baud_calc res[MAX_CLKS];
+ struct baud_calc *resptr, *best, *sptr;
+ int i;
+
+ clkp = cfg->clocks;
+ best = NULL;
+
+ if (cfg->clocks_size < 2) {
+ if (cfg->clocks_size == 0)
+ clkp = &tmp_clksrc;
+
+ /* check to see if we're sourcing fclk, and if so we're
+ * going to have to update the clock source
+ */
+
+ if (strcmp(clkp->name, "fclk") == 0) {
+ struct s3c24xx_uart_clksrc src;
+
+ s3c24xx_serial_getsource(port, &src);
+
+ /* check that the port already using fclk, and if
+ * not, then re-select fclk
+ */
+
+ if (strcmp(src.name, clkp->name) == 0) {
+ s3c24xx_serial_setsource(port, clkp);
+ s3c24xx_serial_getsource(port, &src);
+ }
+
+ clkp->divisor = src.divisor;
+ }
+
+ s3c24xx_serial_calcbaud(res, port, clkp, baud);
+ best = res;
+ resptr = best + 1;
+ } else {
+ resptr = res;
+
+ for (i = 0; i < cfg->clocks_size; i++, clkp++) {
+ if (s3c24xx_serial_calcbaud(resptr, port, clkp, baud))
+ resptr++;
+ }
+ }
+
+ /* ok, we now need to select the best clock we found */
+
+ if (!best) {
+ unsigned int deviation = (1<<30)|((1<<30)-1);
+ int calc_deviation;
+
+ for (sptr = res; sptr < resptr; sptr++) {
+ calc_deviation = baud - sptr->calc;
+ if (calc_deviation < 0)
+ calc_deviation = -calc_deviation;
+
+ if (calc_deviation < deviation) {
+ best = sptr;
+ deviation = calc_deviation;
+ }
+ }
+ }
+
+ /* store results to pass back */
+
+ *clksrc = best->clksrc;
+ *clk = best->src;
+
+ return best->quot;
+}
+
+static void s3c24xx_serial_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+ struct s3c24xx_uart_clksrc *clksrc = NULL;
+ struct clk *clk = NULL;
+ unsigned long flags;
+ unsigned int baud, quot;
+ unsigned int ulcon;
+ unsigned int umcon;
+
+ /*
+ * We don't support modem control lines.
+ */
+ termios->c_cflag &= ~(HUPCL | CMSPAR);
+ termios->c_cflag |= CLOCAL;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+
+ baud = uart_get_baud_rate(port, termios, old, 0, 115200*8);
+
+ if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
+ quot = port->custom_divisor;
+ else
+ quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud);
+
+ /* check to see if we need to change clock source */
+
+ if (ourport->clksrc != clksrc || ourport->baudclk != clk) {
+ s3c24xx_serial_setsource(port, clksrc);
+
+ if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
+ clk_disable(ourport->baudclk);
+ ourport->baudclk = NULL;
+ }
+
+ clk_enable(clk);
+
+ ourport->clksrc = clksrc;
+ ourport->baudclk = clk;
+ }
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ dbg("config: 5bits/char\n");
+ ulcon = S3C2410_LCON_CS5;
+ break;
+ case CS6:
+ dbg("config: 6bits/char\n");
+ ulcon = S3C2410_LCON_CS6;
+ break;
+ case CS7:
+ dbg("config: 7bits/char\n");
+ ulcon = S3C2410_LCON_CS7;
+ break;
+ case CS8:
+ default:
+ dbg("config: 8bits/char\n");
+ ulcon = S3C2410_LCON_CS8;
+ break;
+ }
+
+ /* preserve original lcon IR settings */
+ ulcon |= (cfg->ulcon & S3C2410_LCON_IRM);
+
+ if (termios->c_cflag & CSTOPB)
+ ulcon |= S3C2410_LCON_STOPB;
+
+ umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0;
+
+ if (termios->c_cflag & PARENB) {
+ if (termios->c_cflag & PARODD)
+ ulcon |= S3C2410_LCON_PODD;
+ else
+ ulcon |= S3C2410_LCON_PEVEN;
+ } else {
+ ulcon |= S3C2410_LCON_PNONE;
+ }
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot);
+
+ wr_regl(port, S3C2410_ULCON, ulcon);
+ wr_regl(port, S3C2410_UBRDIV, quot);
+ wr_regl(port, S3C2410_UMCON, umcon);
+
+ dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
+ rd_regl(port, S3C2410_ULCON),
+ rd_regl(port, S3C2410_UCON),
+ rd_regl(port, S3C2410_UFCON));
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ /*
+ * Which character status flags are we interested in?
+ */
+ port->read_status_mask = S3C2410_UERSTAT_OVERRUN;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY;
+
+ /*
+ * Which character status flags should we ignore?
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN;
+ if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= S3C2410_UERSTAT_FRAME;
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->ignore_status_mask |= RXSTAT_DUMMY_READ;
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *s3c24xx_serial_type(struct uart_port *port)
+{
+ switch (port->type) {
+ case PORT_S3C2410:
+ return "S3C2410";
+ case PORT_S3C2440:
+ return "S3C2440";
+ case PORT_S3C2412:
+ return "S3C2412";
+ default:
+ return NULL;
+ }
+}
+
+#define MAP_SIZE (0x100)
+
+static void s3c24xx_serial_release_port(struct uart_port *port)
+{
+ release_mem_region(port->mapbase, MAP_SIZE);
+}
+
+static int s3c24xx_serial_request_port(struct uart_port *port)
+{
+ const char *name = s3c24xx_serial_portname(port);
+ return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY;
+}
+
+static void s3c24xx_serial_config_port(struct uart_port *port, int flags)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+
+ if (flags & UART_CONFIG_TYPE &&
+ s3c24xx_serial_request_port(port) == 0)
+ port->type = info->type;
+}
+
+/*
+ * verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int
+s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+
+ if (ser->type != PORT_UNKNOWN && ser->type != info->type)
+ return -EINVAL;
+
+ return 0;
+}
+
+
+#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
+
+static struct console s3c24xx_serial_console;
+
+#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console
+#else
+#define S3C24XX_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_ops s3c24xx_serial_ops = {
+ .pm = s3c24xx_serial_pm,
+ .tx_empty = s3c24xx_serial_tx_empty,
+ .get_mctrl = s3c24xx_serial_get_mctrl,
+ .set_mctrl = s3c24xx_serial_set_mctrl,
+ .stop_tx = s3c24xx_serial_stop_tx,
+ .start_tx = s3c24xx_serial_start_tx,
+ .stop_rx = s3c24xx_serial_stop_rx,
+ .enable_ms = s3c24xx_serial_enable_ms,
+ .break_ctl = s3c24xx_serial_break_ctl,
+ .startup = s3c24xx_serial_startup,
+ .shutdown = s3c24xx_serial_shutdown,
+ .set_termios = s3c24xx_serial_set_termios,
+ .type = s3c24xx_serial_type,
+ .release_port = s3c24xx_serial_release_port,
+ .request_port = s3c24xx_serial_request_port,
+ .config_port = s3c24xx_serial_config_port,
+ .verify_port = s3c24xx_serial_verify_port,
+};
+
+
+static struct uart_driver s3c24xx_uart_drv = {
+ .owner = THIS_MODULE,
+ .dev_name = "s3c2410_serial",
+ .nr = 3,
+ .cons = S3C24XX_SERIAL_CONSOLE,
+ .driver_name = S3C24XX_SERIAL_NAME,
+ .major = S3C24XX_SERIAL_MAJOR,
+ .minor = S3C24XX_SERIAL_MINOR,
+};
+
+static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = {
+ [0] = {
+ .port = {
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock),
+ .iotype = UPIO_MEM,
+ .irq = IRQ_S3CUART_RX0,
+ .uartclk = 0,
+ .fifosize = 16,
+ .ops = &s3c24xx_serial_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 0,
+ }
+ },
+ [1] = {
+ .port = {
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock),
+ .iotype = UPIO_MEM,
+ .irq = IRQ_S3CUART_RX1,
+ .uartclk = 0,
+ .fifosize = 16,
+ .ops = &s3c24xx_serial_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 1,
+ }
+ },
+#if NR_PORTS > 2
+
+ [2] = {
+ .port = {
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock),
+ .iotype = UPIO_MEM,
+ .irq = IRQ_S3CUART_RX2,
+ .uartclk = 0,
+ .fifosize = 16,
+ .ops = &s3c24xx_serial_ops,
+ .flags = UPF_BOOT_AUTOCONF,
+ .line = 2,
+ }
+ }
+#endif
+};
+
+/* s3c24xx_serial_resetport
+ *
+ * wrapper to call the specific reset for this port (reset the fifos
+ * and the settings)
+*/
+
+static inline int s3c24xx_serial_resetport(struct uart_port *port,
+ struct s3c2410_uartcfg *cfg)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+
+ return (info->reset_port)(port, cfg);
+}
+
+/* s3c24xx_serial_init_port
+ *
+ * initialise a single serial port from the platform device given
+ */
+
+static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
+ struct s3c24xx_uart_info *info,
+ struct platform_device *platdev)
+{
+ struct uart_port *port = &ourport->port;
+ struct s3c2410_uartcfg *cfg;
+ struct resource *res;
+ int ret;
+
+ dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev);
+
+ if (platdev == NULL)
+ return -ENODEV;
+
+ cfg = s3c24xx_dev_to_cfg(&platdev->dev);
+
+ if (port->mapbase != 0)
+ return 0;
+
+ if (cfg->hwport > 3)
+ return -EINVAL;
+
+ /* setup info for port */
+ port->dev = &platdev->dev;
+ ourport->info = info;
+
+ /* copy the info in from provided structure */
+ ourport->port.fifosize = info->fifosize;
+
+ dbg("s3c24xx_serial_init_port: %p (hw %d)...\n", port, cfg->hwport);
+
+ port->uartclk = 1;
+
+ if (cfg->uart_flags & UPF_CONS_FLOW) {
+ dbg("s3c24xx_serial_init_port: enabling flow control\n");
+ port->flags |= UPF_CONS_FLOW;
+ }
+
+ /* sort our the physical and virtual addresses for each UART */
+
+ res = platform_get_resource(platdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ printk(KERN_ERR "failed to find memory resource for uart\n");
+ return -EINVAL;
+ }
+
+ dbg("resource %p (%lx..%lx)\n", res, res->start, res->end);
+
+ port->mapbase = res->start;
+ port->membase = S3C24XX_VA_UART + (res->start - S3C24XX_PA_UART);
+ ret = platform_get_irq(platdev, 0);
+ if (ret < 0)
+ port->irq = 0;
+ else
+ port->irq = ret;
+
+ ourport->clk = clk_get(&platdev->dev, "uart");
+
+ dbg("port: map=%08x, mem=%08x, irq=%d, clock=%ld\n",
+ port->mapbase, port->membase, port->irq, port->uartclk);
+
+ /* reset the fifos (and setup the uart) */
+ s3c24xx_serial_resetport(port, cfg);
+ return 0;
+}
+
+static ssize_t s3c24xx_serial_show_clksrc(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct uart_port *port = s3c24xx_dev_to_port(dev);
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+
+ return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->clksrc->name);
+}
+
+static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
+
+/* Device driver serial port probe */
+
+static int probe_index;
+
+int s3c24xx_serial_probe(struct platform_device *dev,
+ struct s3c24xx_uart_info *info)
+{
+ struct s3c24xx_uart_port *ourport;
+ int ret;
+
+ dbg("s3c24xx_serial_probe(%p, %p) %d\n", dev, info, probe_index);
+
+ ourport = &s3c24xx_serial_ports[probe_index];
+ probe_index++;
+
+ dbg("%s: initialising port %p...\n", __func__, ourport);
+
+ ret = s3c24xx_serial_init_port(ourport, info, dev);
+ if (ret < 0)
+ goto probe_err;
+
+ dbg("%s: adding port\n", __func__);
+ uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
+ platform_set_drvdata(dev, &ourport->port);
+
+ ret = device_create_file(&dev->dev, &dev_attr_clock_source);
+ if (ret < 0)
+ printk(KERN_ERR "%s: failed to add clksrc attr.\n", __func__);
+
+ return 0;
+
+ probe_err:
+ return ret;
+}
+
+EXPORT_SYMBOL_GPL(s3c24xx_serial_probe);
+
+int s3c24xx_serial_remove(struct platform_device *dev)
+{
+ struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+
+ if (port) {
+ device_remove_file(&dev->dev, &dev_attr_clock_source);
+ uart_remove_one_port(&s3c24xx_uart_drv, port);
+ }
+
+ return 0;
+}
+
+EXPORT_SYMBOL_GPL(s3c24xx_serial_remove);
+
+/* UART power management code */
+
+#ifdef CONFIG_PM
+
+static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+
+ if (port)
+ uart_suspend_port(&s3c24xx_uart_drv, port);
+
+ return 0;
+}
+
+static int s3c24xx_serial_resume(struct platform_device *dev)
+{
+ struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+
+ if (port) {
+ clk_enable(ourport->clk);
+ s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port));
+ clk_disable(ourport->clk);
+
+ uart_resume_port(&s3c24xx_uart_drv, port);
+ }
+
+ return 0;
+}
+#endif
+
+int s3c24xx_serial_init(struct platform_driver *drv,
+ struct s3c24xx_uart_info *info)
+{
+ dbg("s3c24xx_serial_init(%p,%p)\n", drv, info);
+
+#ifdef CONFIG_PM
+ drv->suspend = s3c24xx_serial_suspend;
+ drv->resume = s3c24xx_serial_resume;
+#endif
+
+ return platform_driver_register(drv);
+}
+
+EXPORT_SYMBOL_GPL(s3c24xx_serial_init);
+
+/* module initialisation code */
+
+static int __init s3c24xx_serial_modinit(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&s3c24xx_uart_drv);
+ if (ret < 0) {
+ printk(KERN_ERR "failed to register UART driver\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+static void __exit s3c24xx_serial_modexit(void)
+{
+ uart_unregister_driver(&s3c24xx_uart_drv);
+}
+
+module_init(s3c24xx_serial_modinit);
+module_exit(s3c24xx_serial_modexit);
+
+/* Console code */
+
+#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
+
+static struct uart_port *cons_uart;
+
+static int
+s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
+{
+ struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
+ unsigned long ufstat, utrstat;
+
+ if (ufcon & S3C2410_UFCON_FIFOMODE) {
+ /* fifo mode - check ammount of data in fifo registers... */
+
+ ufstat = rd_regl(port, S3C2410_UFSTAT);
+ return (ufstat & info->tx_fifofull) ? 0 : 1;
+ }
+
+ /* in non-fifo mode, we go and use the tx buffer empty */
+
+ utrstat = rd_regl(port, S3C2410_UTRSTAT);
+ return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0;
+}
+
+static void
+s3c24xx_serial_console_putchar(struct uart_port *port, int ch)
+{
+ unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON);
+ while (!s3c24xx_serial_console_txrdy(port, ufcon))
+ barrier();
+ wr_regb(cons_uart, S3C2410_UTXH, ch);
+}
+
+static void
+s3c24xx_serial_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar);
+}
+
+static void __init
+s3c24xx_serial_get_options(struct uart_port *port, int *baud,
+ int *parity, int *bits)
+{
+ struct s3c24xx_uart_clksrc clksrc;
+ struct clk *clk;
+ unsigned int ulcon;
+ unsigned int ucon;
+ unsigned int ubrdiv;
+ unsigned long rate;
+
+ ulcon = rd_regl(port, S3C2410_ULCON);
+ ucon = rd_regl(port, S3C2410_UCON);
+ ubrdiv = rd_regl(port, S3C2410_UBRDIV);
+
+ dbg("s3c24xx_serial_get_options: port=%p\n"
+ "registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n",
+ port, ulcon, ucon, ubrdiv);
+
+ if ((ucon & 0xf) != 0) {
+ /* consider the serial port configured if the tx/rx mode set */
+
+ switch (ulcon & S3C2410_LCON_CSMASK) {
+ case S3C2410_LCON_CS5:
+ *bits = 5;
+ break;
+ case S3C2410_LCON_CS6:
+ *bits = 6;
+ break;
+ case S3C2410_LCON_CS7:
+ *bits = 7;
+ break;
+ default:
+ case S3C2410_LCON_CS8:
+ *bits = 8;
+ break;
+ }
+
+ switch (ulcon & S3C2410_LCON_PMASK) {
+ case S3C2410_LCON_PEVEN:
+ *parity = 'e';
+ break;
+
+ case S3C2410_LCON_PODD:
+ *parity = 'o';
+ break;
+
+ case S3C2410_LCON_PNONE:
+ default:
+ *parity = 'n';
+ }
+
+ /* now calculate the baud rate */
+
+ s3c24xx_serial_getsource(port, &clksrc);
+
+ clk = clk_get(port->dev, clksrc.name);
+ if (!IS_ERR(clk) && clk != NULL)
+ rate = clk_get_rate(clk) / clksrc.divisor;
+ else
+ rate = 1;
+
+
+ *baud = rate / (16 * (ubrdiv + 1));
+ dbg("calculated baud %d\n", *baud);
+ }
+
+}
+
+/* s3c24xx_serial_init_ports
+ *
+ * initialise the serial ports from the machine provided initialisation
+ * data.
+*/
+
+static int s3c24xx_serial_init_ports(struct s3c24xx_uart_info *info)
+{
+ struct s3c24xx_uart_port *ptr = s3c24xx_serial_ports;
+ struct platform_device **platdev_ptr;
+ int i;
+
+ dbg("s3c24xx_serial_init_ports: initialising ports...\n");
+
+ platdev_ptr = s3c24xx_uart_devs;
+
+ for (i = 0; i < NR_PORTS; i++, ptr++, platdev_ptr++) {
+ s3c24xx_serial_init_port(ptr, info, *platdev_ptr);
+ }
+
+ return 0;
+}
+
+static int __init
+s3c24xx_serial_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n",
+ co, co->index, options);
+
+ /* is this a valid port */
+
+ if (co->index == -1 || co->index >= NR_PORTS)
+ co->index = 0;
+
+ port = &s3c24xx_serial_ports[co->index].port;
+
+ /* is the port configured? */
+
+ if (port->mapbase == 0x0) {
+ co->index = 0;
+ port = &s3c24xx_serial_ports[co->index].port;
+ }
+
+ cons_uart = port;
+
+ dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index);
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ else
+ s3c24xx_serial_get_options(port, &baud, &parity, &bits);
+
+ dbg("s3c24xx_serial_console_setup: baud %d\n", baud);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+/* s3c24xx_serial_initconsole
+ *
+ * initialise the console from one of the uart drivers
+*/
+
+static struct console s3c24xx_serial_console = {
+ .name = S3C24XX_SERIAL_NAME,
+ .device = uart_console_device,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .write = s3c24xx_serial_console_write,
+ .setup = s3c24xx_serial_console_setup
+};
+
+int s3c24xx_serial_initconsole(struct platform_driver *drv,
+ struct s3c24xx_uart_info *info)
+
+{
+ struct platform_device *dev = s3c24xx_uart_devs[0];
+
+ dbg("s3c24xx_serial_initconsole\n");
+
+ /* select driver based on the cpu */
+
+ if (dev == NULL) {
+ printk(KERN_ERR "s3c24xx: no devices for console init\n");
+ return 0;
+ }
+
+ if (strcmp(dev->name, drv->driver.name) != 0)
+ return 0;
+
+ s3c24xx_serial_console.data = &s3c24xx_uart_drv;
+ s3c24xx_serial_init_ports(info);
+
+ register_console(&s3c24xx_serial_console);
+ return 0;
+}
+
+#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */
+
+MODULE_DESCRIPTION("Samsung SoC Serial port driver");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/* linux/drivers/serial/samsung.h
+ *
+ * Driver for Samsung SoC onboard UARTs.
+ *
+ * Ben Dooks, Copyright (c) 2003-2005,2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+struct s3c24xx_uart_info {
+ char *name;
+ unsigned int type;
+ unsigned int fifosize;
+ unsigned long rx_fifomask;
+ unsigned long rx_fifoshift;
+ unsigned long rx_fifofull;
+ unsigned long tx_fifomask;
+ unsigned long tx_fifoshift;
+ unsigned long tx_fifofull;
+
+ /* clock source control */
+
+ int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
+ int (*set_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
+
+ /* uart controls */
+ int (*reset_port)(struct uart_port *, struct s3c2410_uartcfg *);
+};
+
+struct s3c24xx_uart_port {
+ unsigned char rx_claimed;
+ unsigned char tx_claimed;
+
+ struct s3c24xx_uart_info *info;
+ struct s3c24xx_uart_clksrc *clksrc;
+ struct clk *clk;
+ struct clk *baudclk;
+ struct uart_port port;
+};
+
+/* conversion functions */
+
+#define s3c24xx_dev_to_port(__dev) (struct uart_port *)dev_get_drvdata(__dev)
+#define s3c24xx_dev_to_cfg(__dev) (struct s3c2410_uartcfg *)((__dev)->platform_data)
+
+/* register access controls */
+
+#define portaddr(port, reg) ((port)->membase + (reg))
+
+#define rd_regb(port, reg) (__raw_readb(portaddr(port, reg)))
+#define rd_regl(port, reg) (__raw_readl(portaddr(port, reg)))
+
+#define wr_regb(port, reg, val) __raw_writeb(val, portaddr(port, reg))
+#define wr_regl(port, reg, val) __raw_writel(val, portaddr(port, reg))
+
+extern int s3c24xx_serial_probe(struct platform_device *dev,
+ struct s3c24xx_uart_info *uart);
+
+extern int s3c24xx_serial_remove(struct platform_device *dev);
+
+extern int s3c24xx_serial_initconsole(struct platform_driver *drv,
+ struct s3c24xx_uart_info *uart);
+
+extern int s3c24xx_serial_init(struct platform_driver *drv,
+ struct s3c24xx_uart_info *info);
+
+#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
+
+#define s3c24xx_console_init(__drv, __inf) \
+static int __init s3c_serial_console_init(void) \
+{ \
+ return s3c24xx_serial_initconsole(__drv, __inf); \
+} \
+ \
+console_initcall(s3c_serial_console_init)
+
+#else
+#define s3c24xx_console_init(drv, inf) extern void no_console(void)
+#endif
+
+#ifdef CONFIG_SERIAL_SAMSUNG_DEBUG
+
+extern void printascii(const char *);
+
+static void dbg(const char *fmt, ...)
+{
+ va_list va;
+ char buff[256];
+
+ va_start(va, fmt);
+ vsprintf(buff, fmt, va);
+ va_end(va);
+
+ printascii(buff);
+}
+
+#else
+#define dbg(x...) do { } while (0)
+#endif
projects / linux-2.6-omap-h63xx.git / commitdiff