Michael Chan [Tue, 22 Jan 2008 01:07:06 +0000 (17:07 -0800)]
[BNX2]: Add link-down workaround on 5706 serdes.
In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 22 Jan 2008 01:06:41 +0000 (17:06 -0800)]
[BNX2]: Fix minor bug in bnx2_has_work().
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/iwlwifi/iwl-3945.c: In function 'iwl3945_add_radiotap':
drivers/net/wireless/iwlwifi/iwl-3945.c:269: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefano Brivio [Sun, 13 Jan 2008 17:35:52 +0000 (18:35 +0100)]
b43legacy: fix use-after-free rfkill bug
Fix rfkill code which caused a use-after-free bug. Thanks to David
Woodhouse for spotting this out.
Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a warning print from ieee80211_sta_stop_rx_ba_session
in case the tid is inactive when interface goes down.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Sun, 13 Jan 2008 16:21:58 +0000 (18:21 +0200)]
mac80211: A-MPDU Rx stop aggregation on proper dev
This patch adds a check to insure that Rx A-MPDU will be stopped only
for the proper device.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 13 Jan 2008 13:16:47 +0000 (14:16 +0100)]
mac80211: Initialize vif pointer
Before calling update_beacon() mac80211 must
initialize the control.vif pointer so it can
be used by the driver to determine which
interface is trying to send the beacon.
v2: ieee80211_beacon_get() should also initialize the
vif pointer since it can be called by mac80211 internally
before calling config_interface().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 16 Jan 2008 14:59:52 +0000 (15:59 +0100)]
libertas: pepper main with debug statement
libertas: re-pepper debug statementThe recent fluff of updates
didn't put proper lbs_deb_enter/leave calls into the source code.
Add them where appropriate.
Also contains some whitespace changes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 16 Jan 2008 14:57:44 +0000 (15:57 +0100)]
libertas: don't blindly try mesh
The CF card only has a very old firmware (5.0.16p0). This firmware doesn't
know anything about mesh config. However, current code blindly calls
mesh_config when the card is inserted. So check the firmware version before
issuing this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
netif_rx should be called only from interrupt context. if_cs and if_sdio receive
packets from other contexts, and thus should call netif_rx_ni.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Tue, 15 Jan 2008 01:46:24 +0000 (17:46 -0800)]
iwlwifi: remove reference to non-existent documentation
The external iwlwifi driver comes with a README file that is
referenced by the Kconfig. This README is not present in the
driver included in the kernel. Remove references to this
documentation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 28 Jan 2008 04:41:38 +0000 (20:41 -0800)]
iwlwifi: 3954 renames iwl3945_rate_scale_priv to iwl3945_rs_sta
This patch renames iwl3945_rate_scale_priv to iwl3945_rs_sta as it
better represents the purpose of this variable.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomas Winkler [Tue, 15 Jan 2008 01:46:21 +0000 (17:46 -0800)]
iwlwifi: 4965 unify rate scale variable names for station data
1, This patch renames iwl4965_rate_scale_priv to iwl4965_lq_sta.
This type represents a station's link quality.
2. The names of the variables of this type were rs_priv, lq_data, lq, crl
across the file. All are now unified under the name lq_sta.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Jan 2008 01:46:20 +0000 (17:46 -0800)]
iwlwifi: move uCode helper functions to iwl-helpers.h
This patch adds iwl_free_fw_desc ucode helper function.
It also moves ucode helper functions to iwl-helpers.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 24 Jan 2008 10:19:38 +0000 (02:19 -0800)]
iwlwifi: fix problem when rf_killswitch change during suspend/resume
After we delay device initialization until interface up, there are more
conditions for the hardware rf_kill switch states during suspend and
resume. For example, before suspend we can have interface up or down,
rf_kill enable or disable; before resume we can have rf_kill enable or
disable. So there are totally 2^3 = 8 conditions to handle. This patch
addressed this problem and makes sure every condition works correctly.
This patch also merges the device suspend and resume handlers with the
mac_start and mac_stop code since they are basically doing the same
thing.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Tue, 15 Jan 2008 01:46:18 +0000 (17:46 -0800)]
iwlwifi: delay firmware loading from pci_probe to network interface open
This patch moves the firmware loading (read firmware from disk and load
it into the device SRAM) from pci_probe time to the first network
interface open time. There are two reasons for doing this:
1. To support kernel buildin iwlwifi drivers. Because kernel initializes
network devices subsystem before hard disk and SATA subsystem, it is
impossible to get the firmware image from hard disk in the PCI probe
handler. Thus delaying the firmware loading into the network
interface open time is the way to go. Note, we only read the firmware
image from hard disk the first time the interface is open. After this
is succeeded, we cache the firmware image into the host memory. This
is a performance gain when user open and close the interface multiple
times and is necessary for device suspend and resume.
2. For better power saving. When the iwlwifi modules are loaded (or
buildin the kernel) but the wireless network interface is not being
used, it is a good practice the wireless device consumes as less
power as possible. Unloading the firmware from the wireless device
and unregister the driver's interrupt handler in the network
interface close handler provides users a way to achieve this. User
space network configuration tools (i.e NetworkManager) can also
contribute here when it detects a wired cable is connected and
close the wireless interface automatically.
This patch also includes the pci_save/restore_state() fixed by Ian Schram
upon the first version.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Ian Schram <ischram@telenet.be> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Jan 2008 01:46:16 +0000 (17:46 -0800)]
iwlwifi: remove iwl4965_tx_cmd
This patch removes iwl4965_tx_cmd function and splits its content to
iwl4965_hw_build_tx_cmd_rate, iwl4965_build_tx_cmd_basic,
and iwl4965_tl_get_stats function. The latest one will be deprecated
when traffic load will move to rate scale module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Jan 2008 01:46:15 +0000 (17:46 -0800)]
iwlwifi: move iwl4965_get_dma_hi_address function to iwl-helpers.h
This patch moves iwl4965_get_dma_hi_address function to iwl-headers.h
as iwl_get_dma_hi_address. This function will be used in more chipsets
than only 4965.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 15 Jan 2008 01:46:14 +0000 (17:46 -0800)]
iwl4965: Remove redundant code in iwl4965_tx_cmd
This function removes redundant code in iwl4965_tx_cmd
function, leftovers of previous design.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Mon, 28 Jan 2008 22:47:41 +0000 (14:47 -0800)]
b43: Add support for new firmware
This patch adds support for new firmware.
Old firmware is still supported until July 2008.
To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Thu, 10 Jan 2008 21:02:44 +0000 (22:02 +0100)]
rt2x00: Data and desc pointer initialization
rt2500usb and rt73usb data and desc pointer initialization
was incorrect because it was using uninitialized variables
to determine the length.
In addition rt2500usb used skb_pull and removed the ieee80211
from each received frame instead of using skb_trim to remove
the device descriptor from the frame.
Finally this also fixes the descriptor override when 4 byte
aligning occured. We still need a completely valid descriptor
when using the TX/RX dumping capabilities in debugfs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 26 Dec 2007 17:26:17 +0000 (18:26 +0100)]
b43: Put multicast frames on the mcast queue
This queues frames flagged as "send after DTIM" by mac80211
on the special multicast queue. The firmware will take care
to send the packet after the DTIM.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 28 Dec 2007 13:32:58 +0000 (14:32 +0100)]
mac80211: add unified BSS configuration
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Wu [Wed, 26 Dec 2007 00:33:16 +0000 (19:33 -0500)]
mac80211: Fix rate reporting regression
Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.
Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an oops which was introduced as a regression by
commit fd640775bd16e1df50c867cc547af0, on the patch titled,
"mac80211: dont use interface indices in drivers".
ieee80211_generic_frame_duration() now relies on sdata->flags which
itself gets set upon bringing the interface up. We check for the
virtual interface now before setting the rate duration registers.
After the mode changes are introduced onto mac80211 we should revisit
these changes.
This patch was tested on the following cards:
1) BG card:
Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF2112A 2GHz radio found (0x46)
2) ABG card:
Atheros AR5213A chip found (MAC: 0x59,PHY: 0x43)
RF5112A multiband radio found (0x36)
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 19 Dec 2007 01:03:33 +0000 (02:03 +0100)]
mac80211: add beacon configuration via cfg80211
This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 19 Dec 2007 00:31:27 +0000 (01:31 +0100)]
mac80211: move interface type to vif structure
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 19 Dec 2007 00:31:26 +0000 (01:31 +0100)]
mac80211: dont use interface indices in drivers
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Wu [Sun, 14 Oct 2007 18:43:16 +0000 (14:43 -0400)]
Add rtl8180 wireless driver
This patch adds a mac80211 based wireless driver for the rtl8180 and
rtl8185 PCI wireless cards. Also included are some rtl8187 changes
required due to the relationship between that driver and this one.
Michael Wu is primarily responsible for the initial driver and rtl8185
support. Andreas Merello provided the additional rtl8180 support.
Thanks to Jukka Ruohonen for the donating a rtl8185 card! It was very
helpful for the rtl8225z2 code.
The Signed-off-by information below is collected from the individual
patches submitted to wireless-2.6 before merging this driver upstream.
Signed-off-by: Andrea Merello <andreamrl@tiscali.it> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Slaby [Sun, 12 Aug 2007 15:33:16 +0000 (17:33 +0200)]
[PATCH] Net: add ath5k wireless driver
add ath5k wireless driver
Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses. Specific license information is cited at the top
of each file.
Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.
Acked-by: Matthew W. S. Bell <mentor@madwifi.org> Acked-by: Michael Taylor <mike.taylor@apprion.com> Acked-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org> Signed-off-by: Bruno Randolf <bruno@thinktube.com> Signed-off-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it> Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Karen Sandler <karen@softwarefreedom.org> Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Matt Norwood <norwood@softwarefreedom.org> Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Richard Fontana <fontana@softwarefreedom.org> Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Thu, 10 Jan 2008 03:16:58 +0000 (22:16 -0500)]
hostap_cs: don't match revisions in presense of the MAC chip name
If the third PCMCIA ID string specifies the MAC chip, the fourth ID
string doesn't need to be matched. Even if it's different, it will be
compatible with the driver.
This ensures that other different revisions of the card will be
supported.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 9 Jan 2008 18:08:49 +0000 (19:08 +0100)]
b43: Remove the PHY spinlock
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:42:04 +0000 (23:42 +0100)]
rt2x00: Correctly initialize data and desc pointer
rt2500usb and rt73usb store the descriptor in different
places. This means we should move the initialization of
the 2 pointers to the driver callback function fill_rxdone().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:41:45 +0000 (23:41 +0100)]
rt2x00: Move init_txring and init_rxring into rt2x00lib
Prior to enabling the radio rt2x00lib should go through all
rings and for each entry should call the callback function
init_txentry() and init_rxentry().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:41:28 +0000 (23:41 +0100)]
rt2x00: Determine MY_BSS from descriptor
Use the MY_BSS descriptor field to determine if the
received frame belongs to the same BSS as the interface.
This can be used by rxdone to determine if the frame
should be updated or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:41:10 +0000 (23:41 +0100)]
rt2x00: Cleanup write_tx_desc() arguments
Send the skb structure with write_tx_desc() and use
the skbdesc structure to read all information about
the frame. This saves several arguments in the function
definition and it is easier to send more information
later as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:40:49 +0000 (23:40 +0100)]
rt2x00: Move packet filter flags
The packet filter flags don't belong in the interface structure
because they are device based instead of interface based.
So move the filter fields out of struct interface and into rt2x00_dev.
Additionally we shouldn't change the filter based on the working
mode, if such a thing is needed than mac80211 should have done that.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:40:07 +0000 (23:40 +0100)]
rt2x00: Move start() and stop() handlers into rt2x00lib.c
suspend & resume was broken since it called rt2x00mac_start()
and rt2x00mac_stop() which would fail to execute because the
DEVICE_PRESENT flag was not set.
Move the start and stop handlers into rt2x00lib.c which are called
from rt2x00mac_start() and rt2x00mac_stop() after they have checked
the DEVICE_PRESENT flag, while suspend and resume handlers can
directly call those functions.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:39:25 +0000 (23:39 +0100)]
rt2x00: Store queue idx and entry idx in data_ring and data_entry
Store the queue idx inside structure data_ring
Store the entry idx inside structure data_entry
This saves us a few calls to ARRAY_INDEX() which is now unused.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:38:58 +0000 (23:38 +0100)]
rt2x00: Only set the TBCN flag when the interface is configured to send beacons.
These flags used to be fixed to one in rt2500pci_config_type, which
caused the beacon timer interrupt to fire. This would lead to
rt2x00lib_beacondone adding work which called
rt2x00lib_beacondone_scheduled which called ieee80211_beacon_get which
printed an error about not having any beacon data.
With this patch, these interrupts are only generated when the interface
is configured to send beacons.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 6 Jan 2008 22:38:34 +0000 (23:38 +0100)]
rt2x00: Always call ieee80211_stop_queue() when return NETDEV_TX_BUSY
Apparently it was possible that ieee80211_stop_queue() was not full while
NETDEV_TX_BUSY was being reported back. I think that is what causing the WARN_ON().
This moves all calls to ieee80211_stop_queue() in rt2x00mac.c where it is easier
to determine if the queue should be halted.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 4 Jan 2008 16:06:29 +0000 (17:06 +0100)]
b43: Add NPHY kconfig option
This adds a new Kconfig option for enabling probing of N-PHYs.
This option will be removed again once the stuff works.
For now it is to help in development. This way real users won't
execute the broken N-PHY codepaths, but the developers can easily
enable N-PHY stuff.
To enable N-PHY probing simply remove the BROKEN dependency
and enable the option in the kernel config.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 26 Dec 2007 13:41:30 +0000 (14:41 +0100)]
b43: Remove PIO support
Remove b43 PIO support.
DMA works well on all supported devices. There's no reason to use PIO.
Additionally, new devices don't support PIO in hardware anymore.
b43 PIO support is dead and unused code.
After applying this patch please do
git rm drivers/net/wireless/b43/pio.h
git rm drivers/net/wireless/b43/pio.c
to remove the main PIO support code.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 22 Dec 2007 21:01:36 +0000 (22:01 +0100)]
ssb: Fix PCMCIA lowlevel register access
This fixes lowlevel register access for PCMCIA based devices.
The patch also adds a temporary workaround for the device mac address.
It simply adds generation of a random address. The real SPROM extraction
will follow in another patch.
The temporary workaround will be removed then, but for now it's OK.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 22 Dec 2007 20:51:30 +0000 (21:51 +0100)]
ssb: Fix extraction of values from SPROM
This fixes extraction of some values from the SPROM.
It mainly fixes extraction of antenna related values, which
is needed for another b43 fix sent later.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Sat, 5 Jan 2008 06:53:11 +0000 (22:53 -0800)]
iwlwifi: fix typo in 'drivers/net/wireless/iwlwifi/Kconfig'
Based on a patch by Miguel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Cc: Miguel Boton <mboton.lkml@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewing the semaphore usage I noticed these down_interruptible calls. Most
of these aren't returning anything, so a caller can't tell if the operation
completed or not. prism54_wpa_bss_ie_get() returns zero, but it's treated as
the function failing which doesn't seem correct.
Signed-off-by: Daniel Walker <dwalker@mvista.com> Cc: Michael Wu <flamingice@sourmilk.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Sunday 02 December 2007 17:17:51 Michael Wu wrote:
> CCK and OFDM power levels are stored in adjacent bytes, not nibbles.
>
This turns out to be true only for rtl8180. On rtl8187, power levels are
indeed stored in nibbles, so this patch is wrong. Please revert this patch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6-omap-h63xx.git / log