Julia Lawall [Wed, 16 Jul 2008 14:34:54 +0000 (16:34 +0200)]
net/ieee80211: adjust error handling
Converts a test in error handling code to a sequence of labels.
The semantic match that found the problem is:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E,E1,E2;
@@
E = alloc_etherdev(...)
... when != E = E1
if (...) { ... free_netdev(E); ... return ...; }
... when != E = E2
(
if (...)
{
... when != free_netdev(E);
return dev; }
|
* if (...)
{
... when != free_netdev(E);
return ...; }
|
register_netdev(E)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Mon, 21 Jul 2008 18:02:46 +0000 (11:02 -0700)]
libertas: support boot commands to write persistent firmware and bootloader
Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively. Add more
suitable error codes for firmware programming process. Add capability checks
for persistent features before attempting to use them.
Based on patches from Brajesh Dave and Priyank Singh.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Louis Rilling [Fri, 15 Aug 2008 19:37:23 +0000 (12:37 -0700)]
[PATCH] configfs: Consolidate locking around configfs_detach_prep() in configfs_rmdir()
It appears that configfs_rmdir() can protect configfs_detach_prep() retries with
less calls to {spin,mutex}_{lock,unlock}, and a cleaner code.
This patch does not change any behavior, except that it removes two useless
lock/unlock pairs having nothing inside to protect and providing a useless
barrier.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com> Signed-off-by: Joel Becker <Joel.Becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Mark Fasheh [Tue, 5 Aug 2008 18:32:46 +0000 (11:32 -0700)]
ocfs2: correctly set i_blocks after inline dir gets expanded
We were setting i_blocks based on allocation before the extent insert, which
is wrong as the value is a calculation based on ip_clusters which gets
updated as a result of the insert. This patch moves the line in question
to just after the call to ocfs2_insert_extent().
Without this fix, inline directories were temporarily having an i_blocks
value of zero immediately after expansion to extents.
Reported-and-tested-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
ocfs2_mark_dead_nodes() was reading journal inodes while holding the
spinlock protecting our in-memory recovery state. The fix is very simple -
the disk state is protected by a cluster lock that's already held, so we
just move the spinlock down past the read.
Reviewed-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Adrian Bunk [Wed, 6 Aug 2008 21:11:12 +0000 (00:11 +0300)]
[PATCH] ocfs2/cluster/tcp.c: make some functions static
Commit 0f475b2abed6cbccee1da20a0bef2895eb2a0edd (ocfs2/net: Silence build
warnings) made sense as far as it fixed compile warnings, but it was not
required that it made the functions global.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Linus Torvalds [Fri, 22 Aug 2008 15:37:07 +0000 (08:37 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Update documentation to remind users to update mke2fs.conf
ext4: Fix small file fragmentation
ext4: Initialize writeback_index to 0 when allocating a new inode
ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC
ext4: journal credit fix for the delayed allocation's writepages() function
ext4: Rework the ext4_da_writepages() function
ext4: journal credits reservation fixes for DIO, fallocate
ext4: journal credits reservation fixes for extent file writepage
ext4: journal credits calulation cleanup and fix for non-extent writepage
ext4: Fix bug where we return ENOSPC even though we have plenty of inodes
ext4: don't try to resize if there are no reserved gdt blocks left
ext4: Use ext4_discard_reservations instead of mballoc-specific call
ext4: Fix ext4_dx_readdir hash collision handling
ext4: Fix delalloc release block reservation for truncate
ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty
ext4: Handle unwritten extent properly with delayed allocation
Linus Torvalds [Fri, 22 Aug 2008 15:36:20 +0000 (08:36 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: fix wrong event handler after online an offlined cpu
Linus Torvalds [Fri, 22 Aug 2008 15:23:53 +0000 (08:23 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: work around MTRR mask setting, v2
x86: fix section mismatch warning - uv_cpu_init
x86: fix VMI for early params
x86: fix two modpost warnings in mm/init_64.c
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
x86: work around MTRR mask setting
x86: PAT Update validate_pat_support for intel CPUs
devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS
x86: PAT proper tracking of set_memory_uc and friends
x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable)
x86: export pv_lock_ops non-GPL
x86, mmiotrace: silence section mismatch warning - leave_uniprocessor
x86: use WARN() in arch/x86/kernel
x86: use WARN() in arch/x86/mm/ioremap.c
werror: fix pci calgary
x86: fix oprofile + hibernation badness
x86, SGI UV: hardcode the TLB flush interrupt system vector
x86: fix Xorg startup/shutdown slowdown with PAT
x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)"
x86 iommu: remove unneeded parenthesis
Linus Torvalds [Fri, 22 Aug 2008 15:22:33 +0000 (08:22 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_it821x: fix warning
libata: Fix a large collection of DMA mode mismatches
ahci: sis controllers actually can do PMP
pata_via: clean up recent tf_load changes
libata: restore SControl on detach
libata: use ata_link_printk() when printing SError
libata: always do follow-up SRST if hardreset returned -EAGAIN
libata: fix EH action overwriting in ata_eh_reset()
sata_mv: add the Gen IIE flag to the SoC devices.
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
sata_mv: don't issue two DMA commands concurrently
libata: implement no[hs]rst force params
Linus Torvalds [Fri, 22 Aug 2008 15:21:48 +0000 (08:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix deadlock on RTNL in ipoib_stop()
IB/ipath: Fix incorrect check for max physical address in TID
IB/ipath: Fix lost UD send work request
Herbert Xu [Fri, 22 Aug 2008 15:04:06 +0000 (01:04 +1000)]
crypto: authenc - Avoid using clobbered request pointer
Authenc works in two stages for encryption, it first encrypts and
then computes an ICV. The context memory of the request is used
by both operations. The problem is that when an asynchronous
encryption completes, we will compute the ICV and then reread the
context memory of the encryption to get the original request.
It just happens that we have a buffer of 16 bytes in front of the
request pointer, so ICVs of 16 bytes (such as SHA1) do not trigger
the bug. However, any attempt to uses a larger ICV instantly kills
the machine when the first asynchronous encryption is completed.
This patch fixes this by saving the request pointer before we start
the ICV computation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Takashi Iwai [Fri, 22 Aug 2008 13:24:22 +0000 (15:24 +0200)]
ALSA: hda - Fix call of alc888_coef_init()
Using init_hook to call alc888_coef_init() is problematic for configurations
that already set another init_hook. Better to put it in alc_init() as is
(although it looks a bit hackish).
Oleg Nesterov [Wed, 20 Aug 2008 23:54:44 +0000 (16:54 -0700)]
wait_task_inactive: "improve" the returned value for ->nvcsw == 0
wait_task_inactive() returns 1 when p->nvcsw == 0 || p->nvcsw == 1. This
means that two subsequent calls can return the same number while the task
was scheduled in between.
Change the code to return "nvcsw | LONG_MIN" instead of "nvcsw ?: 1", now
the overlap always needs LONG_MAX schedules.
Oleg Nesterov [Wed, 20 Aug 2008 23:54:44 +0000 (16:54 -0700)]
wait_task_inactive(): don't consider task->nivcsw
If wait_task_inactive() returns success the task was deactivated. In that
case schedule() always increments ->nvcsw which alone can be used as a
"generation counter".
If the next call returns the same number, we can be sure that the task was
unscheduled. Otherwise, because we know that .on_rq == 0 again, ->nvcsw
should have been changed in between.
Q: perhaps it is better to do "ncsw = (p->nvcsw << 1) | 1" ? This
decreases the possibility of "was it unscheduled" false positive when
->nvcsw == 0.
Marcin Slusarz [Thu, 21 Aug 2008 18:49:05 +0000 (20:49 +0200)]
x86: fix section mismatch warning - uv_cpu_init
WARNING: vmlinux.o(.cpuinit.text+0x3cc4): Section mismatch in reference from the function uv_cpu_init() to the function .init.text:uv_system_init()
The function __cpuinit uv_cpu_init() references
a function __init uv_system_init().
If uv_system_init is only used by uv_cpu_init then
annotate uv_system_init with a matching annotation.
uv_system_init was ment to be called only once, so do it from codepath
(native_smp_prepare_cpus) which is called once, right before activation
of other cpus (smp_init).
Note: old code relied on uv_node_to_blade being initialized to 0,
but it'a not initialized from anywhere.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jarek Poplawski [Fri, 22 Aug 2008 10:24:05 +0000 (03:24 -0700)]
pkt_sched: Fix qdisc list locking
Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.
With feedback from Herbert Xu and David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
FUJITA Tomonori [Fri, 22 Aug 2008 07:29:10 +0000 (16:29 +0900)]
x86: dma_*_coherent rework patchset v2, fix
alloc_coherent dma_ops callback was added to GART, however, it doesn't
return a size aligned address wrt dma_alloc_coherent, as
DMA-mapping.txt defines. This patch fixes it.
This patch also removes unused gart_map_simple
(dma_mapping_ops->map_simple has gone).
Joerg Roedel [Tue, 19 Aug 2008 14:32:45 +0000 (16:32 +0200)]
x86: move dma_*_coherent functions to include file
All the x86 DMA-API functions are defined in asm/dma-mapping.h. This patch
moves the dma_*_coherent functions also to this header file because they are
now small enough to do so.
This is done as a separate patch because it also includes some renaming and
restructuring of the dma-mapping.h file.
Joerg Roedel [Tue, 19 Aug 2008 14:32:44 +0000 (16:32 +0200)]
x86: cleanup dma_*_coherent functions
All dma_ops implementations support the alloc_coherent and free_coherent
callbacks now. This allows a big simplification of the dma_alloc_coherent
function which is done with this patch. The dma_free_coherent functions is also
cleaned up and calls now the free_coherent callback of the dma_ops
implementation.
Joerg Roedel [Tue, 19 Aug 2008 14:32:39 +0000 (16:32 +0200)]
x86: add alloc_coherent dma_ops callback to GART driver
[ v2 - x86: make gart_alloc_coherent return zeroed memory
FUJITA Tomonori pointed it out that the dma_alloc_coherent function
should return memory set to zero. This patch adds this to the GART
implementation too. ]
Jeff Garzik [Fri, 22 Aug 2008 06:33:23 +0000 (02:33 -0400)]
[libata] pata_it821x: fix warning
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function
Alan Cox [Fri, 1 Aug 2008 08:18:34 +0000 (09:18 +0100)]
libata: Fix a large collection of DMA mode mismatches
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 1 Aug 2008 03:51:43 +0000 (12:51 +0900)]
ahci: sis controllers actually can do PMP
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15. However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first. Interestingly, the SRST itself
succeeds but the following commands fail.
If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.
Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Piter PUNK <piterpunk@slackware.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata: always do follow-up SRST if hardreset returned -EAGAIN
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN. However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN. This
makes reset paths more predictable and thus less error-prone.
While at it, move hardreset error checking such that it's done right
after hardreset is finished. This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata: fix EH action overwriting in ata_eh_reset()
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset(). The original intention was to clear reset action
which wasn't selected. This can cause unexpected behavior when other
EH actions are scheduled together with reset. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
x86: build fix in "xen spinlock updates and performance measurements"
Ingo Molnar wrote:
> -tip testing found this build failure:
>
> arch/x86/xen/spinlock.c: In function ‘spin_time_start’:
> arch/x86/xen/spinlock.c:60: error: implicit declaration of function ‘xen_clocksource_read’
>
> i've excluded these new commits for now from tip/master - could you
> please send a delta fix against tip/x86/xen?
Make xen_clocksource_read non-static.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tejun Heo [Wed, 13 Aug 2008 11:24:16 +0000 (20:24 +0900)]
sata_mv: don't issue two DMA commands concurrently
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows. Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Anton Vorontsov [Thu, 21 Aug 2008 18:58:28 +0000 (22:58 +0400)]
genirq: fix irq_desc->depth handling with DEBUG_SHIRQ
When DEBUG_SHIRQ is selected, a spurious IRQ is issued before
the setup_irq() initializes the desc->depth. An IRQ handler may
call disable_irq_nosync(), but then setup_irq() will overwrite
desc->depth, and upon enable_irq() we'll catch this WARN:
That trace corresponds to this line:
WARN(1, KERN_WARNING "Unbalanced enable for IRQ %d\n", irq);
The patch fixes the problem by moving the SHIRQ code below the
setup_irq().
Unfortunately we can't easily move the SHIRQ code inside the
setup_irq(), since it grabs a spinlock, so to prvent a 'real'
IRQ from interfere us we should disable that IRQ.
p.s. The driver in question is drivers/net/phy/phy.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich [Thu, 21 Aug 2008 13:27:22 +0000 (14:27 +0100)]
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
While I don't have a hotplug capable system at hand, I think two issues need
fixing:
- pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in
the after_bootmem case
- the locking done just around phys_pmd_{init,update}() would leave out pgd
updates, and it was needlessly covering code portions that do allocations
(perhaps using a more friendly gfp value in alloc_low_page() would then be
possible)
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roman Zippel [Wed, 20 Aug 2008 23:46:08 +0000 (16:46 -0700)]
ntp: fix ADJ_OFFSET_SS_READ bug and do_adjtimex() cleanup
Thanks to the review by Michael Kerrisk a bug in the recent
ADJ_OFFSET_SS_READ option was discovered, where the ntp time_offset was
inadvertently set by it. This fixes this by making the adjtime code
more separate from the ntp_adjtime code (both of which really want to
be separate syscalls).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rene Herman [Thu, 21 Aug 2008 17:15:46 +0000 (19:15 +0200)]
agp: enable optimized agp_alloc_pages methods
The pageattr-array patch that you currently have in tip/master only
enables it for intel-agp, not the others. The attached enables it for
all drivers currently directly using agp_generic_alloc_page() and
agp_generic_destroy_page() (ocal driver is amd-k7-agp).
The new agp_generic_alloc_pages() interface uses the also new
pageattr array interface API. This makes all AGP drivers that
up to now used generic_{alloc,destroy}_page() use it.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Fri, 22 Aug 2008 03:24:24 +0000 (20:24 -0700)]
x86: work around MTRR mask setting
Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is
usable. Booting with mtrr_show showed us the BIOS-initialized
MTRR settings - which are all wrong.
So the root cause is that the BIOS has not set the mask correctly:
x86, paravirt_ops: use unsigned long instead of u32 for alloc_p*() pfn args
This patch changes the pfn args from 'u32' to 'unsigned long'
on alloc_p*() functions on paravirt_ops, and the corresponding
implementations for Xen and VMI. The prototypes for CONFIG_PARAVIRT=n
are already using unsigned long, so paravirt.h now matches the prototypes
on asm-x86/pgalloc.h.
It shouldn't result in any changes on generated code on 32-bit, with
or without CONFIG_PARAVIRT. On both cases, 'codiff -f' didn't show any
change after applying this patch.
On 64-bit, there are (expected) binary changes only when CONFIG_PARAVIRT
is enabled, as the patch is really supposed to change the size of the
pfn args.
[ v2: KVM_GUEST: use the right parameter type on kvm_release_pt() ]
Per Andersson [Mon, 11 Aug 2008 10:00:52 +0000 (12:00 +0200)]
[ARM] Orion: Fix boot crash on Kurobox Pro
The Kurobox Pro crashes when any of the PCI controller registers
are accessed. This patch adds a function to the Orion PCI handling
code that board support code can call to disable enumerating the
PCI bus entirely, and makes the Kurobox Pro PCI-related init code
call this function.
Signed-off-by: Per Andersson <avtobiff@gmail.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Linus Torvalds [Thu, 21 Aug 2008 23:31:08 +0000 (16:31 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5212/1: pxa: fix build error when CPU_PXA310 is not defined
[ARM] 5208/1: fsg-setup.c fixes
[ARM] fix impd1.c build warning
[ARM] e400 config use MFP
[ARM] e740 config use MFP
[ARM] Fix eseries IRQ limit
[ARM] clocklib: Update users of aliases to new API
[ARM] clocklib: Allow dynamic alias creation
[ARM] eseries: whitespace fixes and cleanup
Greg KH [Thu, 21 Aug 2008 20:47:58 +0000 (13:47 -0700)]
PCI: fix reference leak in pci_get_dev_by_id()
Alex Chiang and Matthew Wilcox pointed out that pci_get_dev_by_id() does
not properly decrement the reference on the from pointer if it is
present, like the documentation for the function states it will.
It fixes a pretty bad leak in the hotplug core (we were leaking an
entire struct pci_dev for each function of each offlined card, the first
time around; subsequent onlines/offlines were ok).
Cc: Matthew Wilcox <matthew@wil.cx> Cc: stable <stable@kernel.org> Tested-by: Alex Chiang <achiang@hp.com> Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Alex Chiang [Thu, 21 Aug 2008 21:13:47 +0000 (15:13 -0600)]
PCI: shpchp: Rename duplicate slot name N as N-1, N-2, N-M...
Commit ef0ff95f136f0f2d035667af5d18b824609de320 (shpchp: fix slot name)
introduces the shpchp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit b3bd307c628af2f0a581c42d5d7e4bcdbbf64b6a (shpchp: add message about
shpchp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
Alex Chiang [Thu, 21 Aug 2008 21:13:29 +0000 (15:13 -0600)]
PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...
Commit 3800345f723fd130d50434d4717b99d4a9f383c8 (pciehp: fix slot name)
introduces the pciehp_slot_with_bus module parameter, which was intended
to help work around broken firmware that assigns the same name to multiple
slots.
Commit 9e4f2e8d4ddb04ad16a3828cd9a369a5a5287009 (pciehp: add message about
pciehp_slot_with_bus option) tells the user to use the above parameter
in the event of a name collision.
This approach is sub-optimal because it requires too much work from
the user.
Instead, let's rename the slot on behalf of the user. If firmware
assigns the name N to multiple slots, then:
The first registered slot is assigned N
The second registered slot is assigned N-1
The third registered slot is assigned N-2
The Mth registered slot becomes N-M
In the event we overflow the slot->name parameter, we report an
error to the user.
This is a temporary fix until the entire PCI core can be reworked
such that individual drivers no longer have to manage their own
slot names.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
pnp: fix "add acpi:* modalias entries"
UIO: generic irq handling for some uio platform devices
UIO: uio_pdrv: fix license specification
UIO: uio_pdrv: fix memory leak
block: drop references taken by class_find_device()
block: fix partial read() of /proc/{partitions,diskstats}
PM: Remove WARN_ON from device_pm_add
driver core: add init_name to struct device
PM: don't skip device PM init when CONFIG_PM_SLEEP isn't set and CONFIG_PM is set
driver model: anti-oopsing medicine
dev_printk(): constify the `dev' argument
drivers/base/driver.c: remove unused to_dev() macro
Documentation: HOWTO-ja_JP-sync patch
Japanese translation of Documentation/SubmitChecklist
kobject: Replace ALL occurrences of '/' with '!' instead of only the first one.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
USB: automatically enable RHSC interrupts
USB: Don't rebind before "complete" callback
USB: Add new PM callback methods for USB
USB: Defer Set-Interface for suspended devices
USB: Add udev argument to interface suspend/resume functions
USB: cdc-acm: don't unlock acm->mutex on error path
MUSB: Fix index register corruption seen with g_ether and Windows host
usb: musb: get rid of MUSB_LOGLEVEL and use parameter
usb: musb: get rid of procfs entry
USB: Fix pxa27x_udc usb speed handling.
USB: cdc-acm: quirk for Conexant CX93010 USB modem
USB: fix bug in usb_unlink_anchored_urbs()
usb-serial: option support HSDPA modem A2502
USB: ISP1760: fixed trivial math in comment
Paul Walmsley [Wed, 21 May 2008 00:41:35 +0000 (18:41 -0600)]
[ARM] OMAP: clockdomain: add clkdm_get_pwrdm()
Add clkdm_get_pwrdm() to the clockdomain code. It will return a
pointer to the powerdomain struct that the clockdomain is contained
within. Used by the PM code.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Thu, 26 Jun 2008 00:09:37 +0000 (18:09 -0600)]
[ARM] OMAP3 pwrdm: add hardware save-and-restore (SAR) support
OMAP3430ES2+ introduces a new feature: optional powerdomain context
hardware save-and-restore (SAR). Currently, this feature only applies
to USBHOST and USBTLL module context when the USBHOST or CORE
powerdomains enter a low-power sleep state[1]. This feature avoids
re-enumeration of USB devices when the powerdomains return from idle,
which is potentially time-consuming.
This patch adds support for enabling and disabling hardware
save-and-restore to the powerdomain code. Three new functions are
added, pwrdm_enable_hdwr_sar(), pwrdm_disable_hdwr_sar(), and
pwrdm_can_hdwr_sar(). A new struct powerdomain "flags" field is
added, with a PWRDM_HAS_HDWR_SAR flag to indicate powerdomains with
SAR support.
Thanks to Jouni Högander <jouni.hogander@nokia.com> for reviewing an
earlier version of these patches, and Richard Woodruff <r-woodruff2@ti.com>
for clarifying the purpose of these bits.
1. For the USBHOST controller module, context loss occurs when the
USBHOST powerdomain enters off-idle. For USBTLL, context loss
occurs either if CORE enters off-idle, or if the CORE logic is
configured to turn off when CORE enters retention-idle (OSWR).
34xx ES2 TRM 4.8.6.1.1, 4.8.6.1.2
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gerald Schaefer [Thu, 21 Aug 2008 17:46:40 +0000 (19:46 +0200)]
[S390] dcssblk: fix race in dcssblk_add_store()
Concurrently adding the same segment may lead to duplicate device_register()
calls, which will trigger an error in kobject code:
"... don't try to register things with the same name in the same directory".
This patch adds a check to avoid this.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] cio: call ccw driver notify function with lock held
Calling a ccw driver's notify function without the ccw device lock
held opens up a race window between discovery and handling of a change
in the device operational state. As a result, the device driver may
encounter unexpected device malfunction, leading to out-of-retry
situations or similar.
Remove race by extending the ccw device lock from state change
discovery to the calling of the notify function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Weinhuber [Thu, 21 Aug 2008 17:46:38 +0000 (19:46 +0200)]
[S390] dasd: fix data size for PSF/PRSSD command
The Perform Subsystem Function/Prepare for Read Subsystem Data
command requires 12 bytes of parameter data, but the respective data
structure dasd_psf_prssd_data has a length of 16 bytes.
Current storage servers ignore the obsolete bytes, but older models
fail to execute the command and report an incorrect length error.
This causes the device initilization for these devices to fail.
To fix this problem we need to correct the dasd_psf_prssd_data
structure and shorten it to the correct length.
Reported-by: Ivan Warren <ivan@vmfacility.fr> Reviewed-by: Ivan Warren <ivan@vmfacility.fr> Tested-by: Ivan Warren <ivan@vmfacility.fr> CC: stable <stable@kernel.org> Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Eric Sandeen [Thu, 21 Aug 2008 17:46:37 +0000 (19:46 +0200)]
[S390] fix ext2_find_next_bit
ext4 does not work on s390 because ext2_find_next_bit is broken. Fortunately
this function is only used by ext4. The function uses ffs which does not work
analog to ffz. The result of ffs has an offset of 1 which is not taken into
account. To fix this use the low level __ffs_word function directly instead
of the ill defined ffs.
In addition the patch improves find_next_zero_bit and ext2_find_next_zero_bit
by passing the bit offset into __ffz_word instead of adding it after the
function call returned.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Thu, 21 Aug 2008 17:46:35 +0000 (19:46 +0200)]
[S390] qdio: remove the module_get & module_put pair
Increasing the qdio reference count for every used subchannel
is unnecessary since unloading qdio (if build as a module) is
only possible if other modules that use qdio are unloaded.
Unloading modules that use qdio in turn requires that these
modules shut down all qdio subchannels. Therefore the additional
module_get reference is not needed.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Thu, 21 Aug 2008 17:46:34 +0000 (19:46 +0200)]
[S390] qdio: improve s390 debug feature usage
Improve s390 debug feature usage:
- log busy bit in dbf
- increase size of dbf views
- consistent logging of qdio api calls to setup view
- print subchannel number so one can associate the interface
with the dbf data
- only log events to one view
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Thu, 21 Aug 2008 17:46:33 +0000 (19:46 +0200)]
[S390] qdio: prevent oopsing if qdio_establish fails
If qdio_establish fails we call qdio_shutdown to cleanup the
qdio subchannel. The tiq_list entry may not be valid at that
time, therefore we must ignore queues with an invalid list entry
in tiqdio_remove_input_queues.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ever since commit 43ca5c3a1cefdaa09231d64485b8f676118bf1e0 ([S390] Convert
monitor calls to function calls.), the kernel refused to IPL with spinlock
debugging enabled.
Julien Brunel [Thu, 21 Aug 2008 17:46:30 +0000 (19:46 +0200)]
[S390] drivers/s390: Use an IS_ERR test rather than a NULL test
In case of error, functions dasd_kmalloc_request and idal_buffer_alloc
return an ERR pointer, but never return the NULL pointer. So after a
call to one of these functions, a NULL test should be replaced by an
IS_ERR test.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x =
(
dasd_kmalloc_request(...)
|
idal_buffer_alloc(...)
)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: USB2VGA dongle found at address 4
usb 1-2: Allocated 8 output buffers
usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32
usb 1-2: New USB device found, idVendor=0711, idProduct=0918
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Signed-off-by: Stefan Lippers-Hollmann <s.L-H@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 20 Aug 2008 21:22:05 +0000 (17:22 -0400)]
USB: automatically enable RHSC interrupts
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 12 Aug 2008 18:34:14 +0000 (14:34 -0400)]
USB: Don't rebind before "complete" callback
This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management. We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support. Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.
The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON. Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.
This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 12 Aug 2008 18:34:10 +0000 (14:34 -0400)]
USB: Add new PM callback methods for USB
This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.
A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure. This way they will be invoked only for USB devices, not
for USB interfaces. The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 12 Aug 2008 18:33:59 +0000 (14:33 -0400)]
USB: Defer Set-Interface for suspended devices
This patch (as1128) fixes one of the problems related to the new PM
infrastructure. We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.
The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed. Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 12 Aug 2008 18:33:27 +0000 (14:33 -0400)]
USB: Add udev argument to interface suspend/resume functions
This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines. Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.
It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexey Dobriyan [Wed, 20 Aug 2008 23:56:04 +0000 (16:56 -0700)]
USB: cdc-acm: don't unlock acm->mutex on error path
On Wed, Jul 23, 2008 at 03:52:36PM +0300, Andrei Popa wrote:
> I installed gnokii-0.6.22-r2 and gave the command "gnokii --identify"
> and the kernel oopsed:
>
> BUG: unable to handle kernel NULL pointer dereference at 00000458
> IP: [<c0444b52>] mutex_unlock+0x0/0xb
> [<c03830ae>] acm_tty_open+0x4c/0x214
projects / linux-2.6-omap-h63xx.git / log