Dave Jones [Tue, 15 Jul 2008 23:54:53 +0000 (19:54 -0400)]
8139too: Make PIO/MMIO a runtime decision through a module parameter.
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wang Jian [Wed, 16 Jul 2008 13:46:17 +0000 (21:46 +0800)]
net/phy: Fix copper/fiber auto-selection for 88e1111
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This timer normally happens once a minute, there is no need to cause an
early wakeup for it, so align it to next second boundary to safe power.
It can't be deferred because then it could take too long on cleanup or DoS.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI PM: make more PCI PM core functionality available to drivers
Make more PCI PM core functionality available to drivers
* Export pci_pme_capable() so that it can be called directly by
drivers (for example, tg3 needs that).
* Move the state choosing part of pci_prepare_to_sleep() to a
separate function, pci_target_state(), that can be called directly
by drivers (for example, tg3 needs that).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adrian Bunk [Tue, 22 Jul 2008 21:21:30 +0000 (14:21 -0700)]
sctp: remove sctp_assoc_proc_exit()
Commit 20c2c1fd6c842caf70dcb1d94b9d58861949fd3d
(sctp: add sctp/remaddr table to complete RFC remote address table OID)
added an unused sctp_assoc_proc_exit() function that seems to have been
unintentionally created when copying the assocs code.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roland Dreier [Tue, 22 Jul 2008 21:20:05 +0000 (14:20 -0700)]
IB/mthca: Keep free count for MTT buddy allocator
MTT entries are allocated with a buddy allocator, which just keeps
bitmaps for each level of the buddy table. However, all free space
starts out at the highest order, and small allocations start scanning
from the lowest order. When the lowest order tables have no free
space, this can lead to scanning potentially millions of bits before
finding a free entry at a higher order.
We can avoid this by just keeping a count of how many free entries
each order has, and skipping the bitmap scan when an order is
completely empty. This provides a nice performance boost for a
negligible increase in memory usage.
Roland Dreier [Tue, 22 Jul 2008 21:19:40 +0000 (14:19 -0700)]
mlx4_core: Keep free count for MTT buddy allocator
MTT entries are allocated with a buddy allocator, which just keeps
bitmaps for each level of the buddy table. However, all free space
starts out at the highest order, and small allocations start scanning
from the lowest order. When the lowest order tables have no free
space, this can lead to scanning potentially millions of bits before
finding a free entry at a higher order.
We can avoid this by just keeping a count of how many free entries
each order has, and skipping the bitmap scan when an order is
completely empty. This provides a nice performance boost for a
negligible increase in memory usage.
Jack Morgenstein [Tue, 22 Jul 2008 21:19:37 +0000 (14:19 -0700)]
mlx4_core: Add module parameter to enable QoS support
Add a module parameter "enable_qos" to mlx4_core. If this param is
set, enable support for QoS in the INIT_HCA command. By default, the
parameter is set to 0 (disabled).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 22 Jul 2008 21:18:33 +0000 (14:18 -0700)]
IB/sa_query: Check if sm_ah is NULL in ib_sa_remove_one()
If update_sm_ah() fails, it leaves the port's sm_ah as NULL. Then if
the device or module is removed, ib_sa_remove_one() will dereference a
NULL pointer when it calls kref_put(). Fix this by testing if sm_ah
is NULL before dropping the reference.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Julia Lawall [Tue, 22 Jul 2008 21:18:10 +0000 (14:18 -0700)]
IB/ehca: Release mutex in error path of alloc_small_queue_page()
The pd->lock mutex is released on a successful return, so it should be
released on an error return as well.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Joachim Fenkes [Tue, 22 Jul 2008 21:18:07 +0000 (14:18 -0700)]
IB/ehca: Filter PATH_MIG events if QP was never armed
Certain firmware versions sometimes cause spurious PATH_MIG events to
occur during QP creation. Filter these events by making sure PATH_MIG
events are only handed down when they actually make sense (i.e. when
the QP has been armed at least once).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz [Tue, 22 Jul 2008 21:16:21 +0000 (14:16 -0700)]
IB/iser: Add support for RDMA_CM_EVENT_ADDR_CHANGE event
Enhance iser to act upon notification on network stack changes that
make its RDMA connection unaligned with the link used by the stack for
the <src,dst> IPs used to establish the connection.
When RDMA_CM_EVENT_ADDR_CHANGE arrives, just disconnect the
connection, assuming that the user space iscsid daemon will reconnect,
and the new connection will be aligned with the IP stack.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Amir Vadai [Tue, 22 Jul 2008 21:14:23 +0000 (14:14 -0700)]
RDMA/cma: Add RDMA_CM_EVENT_TIMEWAIT_EXIT event
Consumers that want to re-use their QPs in new connections need to
know when the QP has exited the timewait state. Report the timewait
event through the rdma_cm.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il> Acked-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz [Tue, 22 Jul 2008 21:14:22 +0000 (14:14 -0700)]
RDMA/cma: Add RDMA_CM_EVENT_ADDR_CHANGE event
Add an RDMA_CM_EVENT_ADDR_CHANGE event can be used by rdma-cm
consumers that wish to have their RDMA sessions always use the same
links (eg <hca/port>) as the IP stack does. In the current code, this
does not happen when bonding is used and fail-over happened but the IB
link used by an already existing session is operating fine.
Use the netevent notification for sensing that a change has happened
in the IP stack, then scan the rdma-cm ID list to see if there is an
ID that is "misaligned" with respect to the IP stack, and deliver
RDMA_CM_EVENT_ADDR_CHANGE for this ID. The consumer can act on the
event or just ignore it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Yong Wang [Tue, 22 Jul 2008 21:14:18 +0000 (14:14 -0700)]
PCI/DMAR: don't assume presence of RMRRs
RMRRs do not necessarily have to be present on all VT-d capable platforms.
The printk is just informational and does not need to be followed by an error
return.
Signed-off-by: Yong Y Wang <yong.y.wang@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: mark gross <mgross@linux.intel.com> Cc: Keshavamurthy, Anil S <anil.s.keshavamurthy@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Dave Jones [Tue, 22 Jul 2008 21:09:06 +0000 (14:09 -0700)]
net: Fix build failure with 'make mandocs'.
The function header comments have to go with the functions
they are documenting, or things go horribly wrong when we
try to process them with the docbook tools.
Warning(include/linux/netdevice.h:1006): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1033): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1067): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1093): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1474): No description found for parameter 'txq'
Error(net/core/dev.c:1674): cannot understand prototype: 'u32 simple_tx_hashrnd; '
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix crash due to missing debugctlmsr on AMD K6-3
x86: add PTE_FLAGS_MASK
x86: rename PTE_MASK to PTE_PFN_MASK
x86: fix pte_flags() to only return flags, fix lguest (updated)
x86: use setup_clear_cpu_cap with disable_apic, fix
x86: move the last Dprintk instance to pr_debug()
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
remove CONFIG_KMOD from core kernel code
remove CONFIG_KMOD from lib
remove CONFIG_KMOD from sparc64
rework try_then_request_module to do less in non-modular kernels
remove mention of CONFIG_KMOD from documentation
make CONFIG_KMOD invisible
modules: Take a shortcut for checking if an address is in a module
module: turn longs into ints for module sizes
Shrink struct module: CONFIG_UNUSED_SYMBOLS ifdefs
module: reorder struct module to save space on 64 bit builds
module: generic each_symbol iterator function
module: don't use stop_machine for waiting rmmod
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (49 commits)
powerpc: Fix build bug with binutils < 2.18 and GCC < 4.2
powerpc/eeh: Don't panic when EEH_MAX_FAILS is exceeded
fbdev: Teaches offb about palette on radeon r5xx/r6xx
powerpc/cell/edac: Log a syndrome code in case of correctable error
powerpc/cell: Add DMA_ATTR_WEAK_ORDERING dma attribute and use in Cell IOMMU code
powerpc: Indicate which oprofile counters to use while in compat mode
powerpc/boot: Change spaces to tabs
powerpc: Remove duplicate 6xx option in Kconfig
powerpc: Use PPC_LONG and PPC_LONG_ALIGN in lib/string.S
powerpc: Use PPC_LONG_ALIGN in uaccess.h
powerpc: Add a #define for aligning to a long-sized boundary
powerpc: Fix OF parsing of 64 bits PCI addresses
powerpc: Use WARN_ON(1) instead of __WARN()
powerpc: Fix support for latencytop
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add a sub-match id to ps3_system_bus
powerpc: Add a 6xx defconfig
powerpc/dma: Use the struct dma_attrs in iommu code
powerpc/cell: Add support for power button of future IBM cell blades
powerpc/cell: Cleanup sysreset_hack for IBM cell blades
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (79 commits)
arm: bus_id -> dev_name() and dev_set_name() conversions
sparc64: fix up bus_id changes in sparc core code
3c59x: handle pci_name() being const
MTD: handle pci_name() being const
HP iLO driver
sysdev: Convert the x86 mce tolerant sysdev attribute to generic attribute
sysdev: Add utility functions for simple int/ulong variable sysdev attributes
sysdev: Pass the attribute to the low level sysdev show/store function
driver core: Suppress sysfs warnings for device_rename().
kobject: Transmit return value of call_usermodehelper() to caller
sysfs-rules.txt: reword API stability statement
debugfs: Implement debugfs_remove_recursive()
HOWTO: change email addresses of James in HOWTO
always enable FW_LOADER unless EMBEDDED=y
uio-howto.tmpl: use unique output names
uio-howto.tmpl: use standard copyright/legal markings
sysfs: don't call notify_change
sysdev: fix debugging statements in registration code.
kobject: should use kobject_put() in kset-example
kobject: reorder kobject to save space on 64 bit builds
...
Switch to ioremap_wc(). We keep the MTRR code since ioremap_wc()
will use UC_MINUS when falling back to uncachable, and thus let
the MTRR WC take precedence.
Also rename the error path better.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wang Chen [Tue, 22 Jul 2008 05:13:18 +0000 (13:13 +0800)]
de4x5: Remove developer debug feature about set/clear promisc
IFF_PROMISC flag shouldn't be set or cleared by drivers, because
whether device be promisc mode is decided by how many upper layer
callers being referenced to it.
And the promisc changing feature of de4x5 ioctl is developer debug
feature, we can remove it now.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CC drivers/s390/net/qeth_l3_main.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/s390/net/qeth_l3_main.c:
In function 'qeth_l3_hard_start_xmit':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/s390/net/qeth_l3_main.c:
2654: error: implicit declaration of function 'VLAN_TX_SKB_CB'
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/s390/net/qeth_l3_main.c:
2654: error: invalid type argument of '->' (have 'int')
make[3]: *** [drivers/s390/net/qeth_l3_main.o] Error 1
The intention of the driver appears to be to invalidate the VLAN tag.
Change it to set skb->vlan_tci to zero, which has the same effect.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
fs_enet: Remove unused fields in the fs_mii_bb_platform_info structure.
The mdio_port, mdio_bit, mdc_port and mdc_bit fields in the
fs_mii_bb_platform_info structure are left-overs from the move to the Phy
Abstraction Layer subsystem. They are not used anymore and can be safely
removed.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Tue, 22 Jul 2008 12:44:14 +0000 (13:44 +0100)]
istallion: Use helpers
The ldisc needs to be referenced properly when used. The tty layer has a
helper for this which should have been used but this driver got missed
originally.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:22:14 +0000 (11:22 +0100)]
synclink_gt: add rx DMA buffer fill level control
Add run time control for receive DMA buffer fill level to allow
application to control receive latency when using stream oriented serial
protocols that pass receive data to application only after a DMA buffer
fills. This was previously a compile time option, but run time control is
needed when application changes data rate (and latency requirements) or
uses different data rates on different ports.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:22:04 +0000 (11:22 +0100)]
synclink_gt: leave transmitter in reset state after configuration
Leave the transmitter in reset state after configuration so that transmit
signal is held at mark until transmitter is explicitly enabled by
application, otherwise transmitter sends idle pattern.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:55 +0000 (11:21 +0100)]
synclink_gt: improve TIOCOUTQ accuracy
Improve the accuracy of TIOCOUTQ value as implemented in chars_in_buffer()
method by walking and counting tx DMA buffers, reading controller tx FIFO
level and accounting for controller tx shift register. The greatly
improves application control of transmit latency at lower data rates.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:28 +0000 (11:21 +0100)]
synclink_gt: improve and simplify write method
Improve write method by allowing multiple HDLC frames to be loaded into tx
DMA buffer ring for continuous frame transmission. This simplifies the
transmit code by using the common procedures for all serial protocols.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Jul 2008 10:21:07 +0000 (11:21 +0100)]
serial: 8250: fix shared interrupts issues with SMP and RT kernels
With SMP kernels _irqsave spinlock disables only local interrupts, while
the shared serial interrupt could be assigned to the CPU that is not
currently starting up the serial port.
This might cause issues because serial8250_startup() routine issues
IRQ-triggering operations before registering the port in the IRQ chain
(though, this is fine to do and done explicitly because we don't want to
process any interrupts on the port startup).
With RT kernels and preemptable hardirqs, _irqsave spinlock does not
disable local hardirqs, and the bug could be reproduced much easily:
After this, all serial ports on the given IRQ are non-functional.
To fix the issue we should explicitly disable shared IRQ before
issuing any IRQ-triggering operations.
I also changed spin_lock_irqsave to the ordinary spin_lock, since it
seems to be safe: chain does not contain new port (yet), thus nobody
will interfere us from the ISRs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:18:03 +0000 (11:18 +0100)]
tty: rework break handling
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:53 +0000 (11:17 +0100)]
tty: Mark unconverted drivers as BROKEN
Nobody seems to use these drivers anyway so if they want them they can
fix them up. I don't have the needed info to add break_ctl support to them.
Send patches if you don't like it.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:16 +0000 (11:17 +0100)]
specialix: Code cleanups
Go through the inlines and other oddments that are iffy. Remove various bits
of dead code and bogus debug. Turn the crtsdts compile time option into a
runtime switch.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log