nl80211: Fix comment merge error

The comments ended up in the wrong place due to a merge error.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: removing IWL4965_HT config

This patch removes CONFIG_IWL4965_HT #ifdefs for iwl 4965 and 5000. 11n
feature is stable in those drivers and its mode of operation is determined
in mac80211, so this dependency is not needed any more.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: cleanup: rename and remove local pointers

Mixed use of 'dev' and 'usbdev' for usbnet pointer can be confusing. So changing all 'usbnet *dev' to 'usbnet *usbdev'.

Also remove 'net_device *net' pointer from 'rndis_wext_bind' as 'usbdev->net' were already used where needed.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: check if set_multicast_list work is already scheduled

Don't queue set_multicast_list work if WORK_SET_MULTICAST_LIST
flag already set.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: update carrier flag when link state changes

Driver wasn't updating netif_carrier on link state changes but assumed
link layer was always up.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: do link-down state change in worker thread

rndis_wext_link_change() is called from within rndis_command() so it
isn't very good place to do any work. Move to worker thread.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: use simple_read_from_buffer()

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Rework alignment check.

Rework the alignment check in rt2x00dev.c to be independent of any
potential alignment measures that may be taken before. Just check
whether the payload is aligned based on the pointer addresses.

Note: This is preparatory for the dynamically mapped skb buffers
for the PCI drivers, as these need 4-byte alignment instead of the
currently enforced offset by 2 bytes.

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove unused defines

MAX_RX_SSI and MAX_NOISE are no longer used,
it is better to remove them entirely.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Clear IEEE80211_TX_CTL_USE_RTS_CTS flag for RTS frame

For RTS/CTS-to-self frames the IEEE80211_TX_CTL_USE_RTS_CTS flag
should be cleared for the tx_info flags.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use __builtin_choose_expr() instead of ?:

To really force the FIELD macros to determine
the first bit of the register field we should
use the __builtin_choose_expr() function.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix double usage of skb->cb in USB RX path.

It is not safe to use the skb->cb area for both the rxd and
skb_frame_desc data at the same time, while they occupy an overlapping
piece of memory. This can lead to hard to trace crashes as pointers
within skb_frame_desc are pointing into nowhere, or the rxd data is
overwritten with non-sense.

Fix it by copying the rxd to a small buffer on the stack.

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Centralize RX packet alignment handling in rt2x00lib.

When rt2x00pci will be switched over to dynamically mapped skb's
instead of statically allocated DMA buffers, it no longer can handle
alignment of RX packets in a copy step, and needs to implement the
same scheme as rt2x00usb does.

In order to make the patch on dynamically mapped skb's smaller,
already centralize the alignment handling into rt2x00lib. This allows
us to move more code in rt2x00lib, and thus remove code duplication
between rt2x00usb and rt2x00pci.

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Cleanup struct skb_frame_desc.

The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't kick TX queue after each frame

TX queues shouldn't be kicked after each frame that is put into the
queue.  This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.

In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move generic TX frame writing code into rt2x00queue

The write_tx_data functions in rt2x00pci and rt2x00usb have
a lot in common. This moves that duplicate code into
rt2x00queue_write_tx_frame().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement rt2x00usb_kick_tx_queue()

rt2x00usb_kick_tx_queue() will loop over all entries
within the INDEX_DONE->INDEX range and kick each entry
which is pending to be kicked. This makes the kick_tx_queue
approach work the same as with the PCI drivers which
will allow for more code generalisation into rt2x00lib.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix queue initialization

qid should be initialized to QID_BEACON and QID_ATIM
for the beacon and atim quue. This makes checking for
a particular queue much saner, and it shouldn't harm,
because the only places where the value is send to
the hardware, we are allowed to send any value we
want since it is only used as argument in the
TX done register.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.1.7

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Make rt2x00_set/get_field macros

The rt2x00_set_field functions are very often used,
but GCC is better able to optimize them when they
are macros instead of static inline functions.

After changing it to macro's each rt2x00 driver will
loose about ~3500 bytes in size.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Removed unused descriptor read in txdone

rt2x00usb doesn't need the TX descriptor in the TX done path.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove CTS/RTS check in tx()

mac80211 doesn't send RTS or CTS-to-self frames through
the tx() callback functions so we don't need to check it.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move led initialization into function

Reduce code duplication by moving led structure initialization
into a per-driver function.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Cleanup/optimize set_state() function callback function

* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages

This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Calculate register offset during compile time

By using __ffs() the register offsets were always calculated
at run-time which all FIELD32/FIELD16 definitions were builtin
constants. This means we can heavily optimize the register handling
by allowing GCC to do all the work during compilation.

Add some compile_ffs() macros to perform the calculation at
compile time. After this each rt2x00 module size is reduced
by ~2500 bytes. And the stack size of several functions is reduced
as well which further limits the number of rt2x00 results in
'make checkstack'.

v2: Merge GertJan's bugfix of patch [1/11] directly into this patch
      instead of providing it as seperate patch.
v3: Add extra parentheses when bitshifting __x

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ftrace: fix "notrace" filtering priority

This is a fix to give notrace filter rules priority over "set_ftrace_filter"
rules.

This fix ensures that functions which are set to be filtered and are
concurrently marked as "notrace" don't get recorded. As of now, if
a record is marked as FTRACE_FL_FILTER and is enabled, then the notrace
flag is not checked. Tested on x86-32.

Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

ACPI: no AC status notification

http://bugzilla.kernel.org/show_bug.cgi?id=10695

Signed-off-by: Len Brown <len.brown@intel.com>

ACPI Exception (video-1721): UNKNOWN_STATUS_CODE, Cant attach device

The child of a video bus device is not alway a video device.
It should be a warn message rather than an exception here.
http://bugzilla.kernel.org/show_bug.cgi?id=9761

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

Conflicts:

drivers/net/smc911x.c

[WATCHDOG 32/57] pcwd: clean up, unlocked_ioctl usage

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

rt2x00: Add D-link DWA111 support

Add new rt73usb USB ID for D-Link DWA111

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing new line in debug print HT_DEBUG

This patch adds '\n' in debug printk (wme.c HT DEBUG)

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 : fix for iwconfig in ad-hoc mode

The patch checks interface status, if it is in IBSS_JOINED mode
show cell id it is associated with.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Fix coherent DMA mask for PCI devices

This fixes setting the coherent DMA mask for PCI devices.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: LEDS build failure

Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.

The alternative is to select NEW_LEDS, which some drivers do.

This patch fixes the led_* symbols build errors.

(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: INPUT build failure

Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.

This patch fixes the input_* symbols build errors.

(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix noise calculation WARN_ON

This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample

The comment in the patch describes why it's safe to simply remove
the check.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix possible NULL pointer dereference in DMA code

This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().

This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.

Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Restrict DMA to 32-bit addresses.

None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.

Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't kill guardian_urb when it wasn't created

This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[WATCHDOG 31/57] pc87413_wdt: clean up, coding style, unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 30/57] omap_wdt: locking, unlocked_ioctl, tidy

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 29/57] mv64x60_wdt: clean up and locking checks

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 28/57] mtx-1_wdt: clean up, coding style, unlocked ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 27/57] mpcore watchdog: unlocked_ioctl and BKl work

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 26/57] mpc watchdog: clean up and locking

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 25/57] mixcomwd: coding style locking, unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 24/57] machzwd: clean up, coding style, unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 23/57] ks8695_wdt: clean up, coding style, unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 22/57] ixp4xx_wdt: unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 21/57] ixp2000_wdt: clean up and unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

[WATCHDOG 20/57] booke watchdog: clean up and unlocked_ioctl

Review and switch to unlocked_ioctl

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: update my email address
  parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3
  parisc: fix off by one in setup_sigcontext32
  parisc: export empty_zero_page
  parisc: export copy_user_page_asm
  parisc: move head.S to head.text section
  Revert "parisc: fix trivial section name warnings"

parisc: update my email address

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3

ip_fast_csum needs an asm "memory" clobber, otherwise the aggressive
optimizations in gcc-4.3 cause it to be miscompiled.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

parisc: fix off by one in setup_sigcontext32

Thankfully, the values were irrelevant... Spotted by
newer gcc.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

parisc: export empty_zero_page

Needed by ext4 when built as a module.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

parisc: export copy_user_page_asm

Needed by fuse (via copy_highpage).

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

parisc: move head.S to head.text section

And explicitly list it in vmlinux.lds...

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Revert "parisc: fix trivial section name warnings"

This reverts commit bd3bb8c15b9a80dbddfb7905b237a4a11a4725b4.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

ALSA: make snd_ctl_elem_read() and snd_ctl_elem_write() static

snd_ctl_elem_read() and snd_ctl_elem_write() are no longer used by
any other drivers.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - Remove unused mutex

Removed unused mutex from patch_*.c.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - Fix stac9205_cfg_tbl

Sort stac9205_cfg_table in the order of id numbers, and removed the
duplicated (obsoleted) entries for 0x01fc and 0x01fd.  This doesn't
change the driver behavior since the old entries are all secondary.

The duplication occured due to commit dfe495d0, and the old entries
were introduced by commit ae0a8ed8.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Cover also Nokia N810 WiMAX Edition in N810 machine driver

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Add TLV information to the LM4857 controls on the GTA01

Signed-off-by: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Add SOC_SINGLE_EXT_TLV control type

Signed-off-by: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Add TLV information to remaining WM8753 controls

Signed-off-by: Mike Montour <mail@mmontour.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Fix WM9713 voice PCM slave mode configuration

Reported-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Pass the DAI being configured into CPU DAI probe and remove

This allows per-DAI initialisation to be done by the CPU DAI drivers.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Add missing includes

Ensure that DAIs are prototyped in the codec drivers that define them.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Tweak tlv320aicx reg_cache_size

ASoC codec drivers frequently set the register cache size using sizeof()
rather than ARRAY_SIZE(). For tlv320aicx either is correct since the
registers are 8 bit but update to use ARRAY_SIZE() for clarity.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Fix register cache size for UDA1380

The register cache size is used by the codec_reg sysfs file which works in
terms of the register cache access functions rather than in terms of raw
access to the cache so the size specified needs to be in terms of the
number of elements.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: ASoC: Fix register cache sizes for Wolfson codecs

The register cache size is used by the codec_reg sysfs file which works in
terms of the register cache access functions rather than in terms of raw
access to the cache so the size specified needs to be in terms of the
number of elements.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: opti93x: use cs4231 lib

This patch converts the Opti93x driver to use
the cs4231 library instead of duplicating the code.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: opti93x: add support for Opti93x codec in cs4231-lib

This patch adds support for WSS compatible Opti93x
codec to the cs4231-lib.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - Add a warning if pending IRQ is found

The pending IRQ handling is a very hackish workaround and should be
avoided as much as possible via a larger bdl_pos_adj option value.
Put a warning message if this situation occurs so that the user may have
a chance to notice that something is wrong.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ahci: Workaround HW bug for SB600/700 SATA controller PMP support
  ahci: workarounds for mcp65

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  tcp: Revert 'process defer accept as established' changes.
  ipv6: Fix duplicate initialization of rawv6_prot.destroy
  bnx2x: Updating the Maintainer
  net: Eliminate flush_scheduled_work() calls while RTNL is held.
  drivers/net/r6040.c: correct bad use of round_jiffies()
  fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
  ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
  netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
  netfilter: Make nflog quiet when no one listen in userspace.
  ipv6: Fail with appropriate error code when setting not-applicable sockopt.
  ipv6: Check IPV6_MULTICAST_LOOP option value.
  ipv6: Check the hop limit setting in ancillary data.
  ipv6 route: Fix route lifetime in netlink message.
  ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
  dccp: Bug in initial acknowledgment number assignment
  dccp ccid-3: X truncated due to type conversion
  dccp ccid-3: TFRC reverse-lookup Bug-Fix
  dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
  dccp: Fix sparse warnings
  dccp ccid-3: Bug-Fix - Zero RTT is possible

ALSA: hda - Add description of bdl_pos_adj option

Added a brief description of the new bdl_pos_adj option to
ALSA-Configuration.txt.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - Fix bdl_pos_adj value for ATI SB chipsets

ATI SB controllers seem to report the DMA ahead in the amount of FIFO.
Thus bdl_pos_adj should be 32 for them as default.

Also, the default value is set to -1, which means to make the driver
to choose the appropriate value.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - bdl_pos_adj option to each instance

The option bdl_pos_adj should be provided for each card instance instead of
a global one because the value depends rather on each controller-chip.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: get leo framebuffer working

ALSA: hda - remove position_fix=3

position_fix=3 is the option to correct the DMA position with the
FIFO size.  But, it never worked correctly, and we have now more other
workarounds for the DMA position fixes.  Thus better to remove it.

Also, change POS_FIX_NONE to POS_FIX_LPIB to represent its real role
better.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: hda - Add bdl_pos_adj option

Added a new option, bdl_pos_adj, to adjust the delay of IRQ-wakeup
timing.

Most HD-audio hardwares have a problem that a BDL IRQ is issued before
actually the data and the DMA pointer are updated.
We have already a mechanism to force to delay snd_pcm_period_elapsed()
calls via workq, but this costs much CPU, and typically the delay is
within one sample.  Thus, it's more clever to adjust the BDL entries
instead.

The new option adds the size of the delay in frames.  As default,
it's set to 1 -- that is, one sample delay.  Even the hardware is
really correct, one sample delay is relatively harmless in comparison
with reporting wrong positions.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

sound: sound/oss/dmasound/: cleanups

This patch contains the following cleanups:
- make the following needlessly global functions static:
  - dmasound_core.c: get_afmt_string()
  - dmasound_paula.c: dmasound_paula_init()
  - dmasound_q40.c: dmasound_q40_init()
- remove the following unused global variable:
  - dmasound_core.c: software_input_volume

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

ALSA: emu10k1 - Fix page allocation with GFP_DMA

Added the missing GFP_ATOMIC to page_alloc when called with GFP_DMA.
GFP_KERNEL often results in stalls for ZONE_DMA, so GFP_ATOMIC is more
prgmatic.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

[ALSA] hda - Add Toshiba dynabook SS RX1 support

I have Toshiba dynabook SS RX1 and this patch adds that support.

Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

[ALSA] opti93x: fix sound ouput for Opti930

This patch fixes silenced output from the Opti930.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

[ALSA] ac97 - Fix power_save option value as time-out

The power_save option was set as boot although it was meant to be a
timeout value like the same option of snd-hda-intel originally.
Now fixed to the same style.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

[ALSA] ASoC: Fix default mono mixer configuration for WM8510

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

[ALSA] ac97: add support for wm9711 master left inv switch

This patch adds support for Master Left Inv Switch on wm9711.
At least required to drive the mono speaker on the PXA270 platfrom

Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

stacktrace: print_stack_trace() cleanup

- shorter code and better atomicity with regards to printk().

(It's been tested with the backtrace self-test code on i386 and x86_64.)

Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

udp: reorder udp_iter_state to remove padding on 64bit builds

reorder udp_iter_state to remove padding on 64bit builds

shrinks from 24 to 16 bytes, moving to a smaller slab when
CONFIG_NET_NS is undefined & seq_net_private = {}

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

cputopology: always define CPU topology information, clean up

simplify drivers/base/topology.c a bit.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

cpu topology: always define CPU topology information

This can result in an empty topology directory in sysfs, and requires
in-kernel users to protect all uses with #ifdef - see
<http://marc.info/?l=linux-netdev&m=120639033904472&w=2>.

The documentation of CPU topology specifies what the defaults should be if
only partial information is available from the hardware.  So we can
provide these defaults as a fallback.

This patch:

- Adds default definitions of the 4 topology macros to <linux/topology.h>
- Changes drivers/base/topology.c to use the topology macros unconditionally
  and to cope with definitions that aren't lvalues
- Updates documentation accordingly

[ From: Andrew Morton <akpm@linux-foundation.org>
  - fold now-duplicated code
  - fix layout
]

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: John Hawkes <hawkes@sgi.com>
Cc: Zhang, Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

lockdep: output lock_class key instead of address for forward dependency output

The key instead of address of lock_class should be output in
/proc/lockdep when forward dependency is output, because key is
output for lock_class itself as identifier too.

This patch is based on x86/auto-latest branch of git-x86 tree, and has
been tested on x86_64 platform.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

ahci: Workaround HW bug for SB600/700 SATA controller PMP support

There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ahci: workarounds for mcp65

MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability.  Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drm: the sg alloc ioctl should write back the handle to userspace

Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: use drms ioctl cmd not what we get passed from userspace.

This enforces us to use the drm ioctl types so read/write works correctly and not believe
what userspace tells us.

It does this hopefully without breaking the drm api.

Fixes bug from thread: BUG: unable to handle kernel NULL pointer dereference (drm_getunique)

Signed-off-by: Dave Airlie <airlied@redhat.com>