Ben Dooks [Tue, 15 Apr 2008 10:36:18 +0000 (11:36 +0100)]
[MTD] [NAND] S3C2410 Fix previous nFCE suspend save patch
Commit 03680b1e00d146df718c8a4eac34438566b70c85 incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Mon, 14 Apr 2008 06:39:39 +0000 (09:39 +0300)]
[MTD] [OneNAND] Allow for controller errors when reading
A power loss while writing can result in a page becoming unreadable.
When the device is mounted again, reading that page gives controller
errors. Upper level software like JFFS2 treat -EIO as fatal, refusing to
mount at all. That means it is necessary to treat the error as an ECC
error to allow recovery. Note that typically in this case, the
eraseblock can still be erased and rewritten i.e. it has not become a
bad block.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Trent Piepho [Mon, 31 Mar 2008 04:19:30 +0000 (21:19 -0700)]
[MTD] [NOR] Fixup for incorrect CFI data in Spansion S29GL064/32N flash chips
This is a known erratum confirmed by Spansion. I have an errata document,
but I can't find a link to it anywhere on their site to include here.
Some of the S29GL064N chips report 64 sectors when they should report 128,
and some of S29GL032N chips report 127 sectors when they should report 63.
Note that when the chip dies are fixed by Spansion, they will still have
the same id. The fix is done in such a way that it won't affect corrected
chips.
The fixups use the extended id made available by a previous patch. Without
that, virtually all newer AMD/Spansion chips will have the same ID (0x227e)
and it's not possible to apply the fixup to the correct chips.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Kay Sievers [Tue, 22 Apr 2008 20:16:49 +0000 (22:16 +0200)]
i2c: Fix platform driver hotplug/coldplug
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Magnus Damm [Tue, 22 Apr 2008 20:16:49 +0000 (22:16 +0200)]
i2c: New driver for the SuperH Mobile I2C bus controller
This is V5 of the SuperH Mobile I2C Controller Driver. A simple Master
only driver for the I2C block included in processors such as sh7343,
sh7722 and sh7723. Tested on a sh7722 MigoR using a rs5c732b rtc.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Hans Schillstrom [Tue, 22 Apr 2008 20:16:48 +0000 (22:16 +0200)]
i2c-bfin-twi: Fix mismatch in add timer and delete timer
Move init_completion to just before i2c transfer.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3385
Signed-off-by: Hans Schillstrom <hans.schillstrom@shlsys.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Blackfin TWI controller hardware pin should be requested from GPIO port controller
Before BF54x, there is no need to do this. But as long as BF54x and BF52x
are supported by this generic driver, the missing pin mux operation should be
added.
Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c-bfin-twi: Add platform_resource interface to support multi-port TWI controllers
- Dynamic alloc the resource of TWI driver data according to board information
- TWI register read/write accessor based on dynamic regs_base
- Support TWI0/TWI1 for BF54x
Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 22 Apr 2008 20:16:47 +0000 (22:16 +0200)]
i2c-dev: Split i2cdev_ioctl
Split the handling of the I2C_RDWR and I2C_SMBUS ioctls to their own
functions. This limits the stack usage, saves one level of indentation
and makes the code more readable.
Sean MacLennan [Tue, 22 Apr 2008 20:16:47 +0000 (22:16 +0200)]
i2c-ibm_iic: Support building as an of_platform driver
This patch allows the i2c-ibm_iic driver to be built either as an ocp
driver or an of_platform driver. This allows it to run under the powerpc
arch but maintains backward compatibility with the ppc arch.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wolfram Sang [Tue, 22 Apr 2008 20:16:46 +0000 (22:16 +0200)]
i2c-algo-pca: Extend for future drivers
The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.
Concerning the core struct i2c_algo_pca_data:
- A private data field was added, all hardware dependant data may go here.
Similar to other algorithms, now a pointer to this data is passed to the
adapter's functions. In order to make as less changes as possible to the
ISA-driver, it leaves the private data empty and still only uses its static
variables.
- A "reset_chip" function pointer was added; such a functionality must come
from the adapter, not the algorithm.
- use a variable "i2c_clock" instead of a function pointer "get_clock",
allowing for write access to a default in case a wrong value was supplied.
In the algorithm-file:
- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused
(The state-machine for I2C-communication was not touched.)
In the ISA-driver:
- adapt to new algorithm
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wolfram Sang [Tue, 22 Apr 2008 20:16:46 +0000 (22:16 +0200)]
i2c-algo-pca: Remove trailing whitespaces and unnecessary UTF
Remove trailing whitespaces to make further patches more readable. Also remove
an unnecessary UTF-char for simplicity ("us" for microseconds is fine enough).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 22 Apr 2008 20:16:46 +0000 (22:16 +0200)]
i2c: Remove the algorithm drivers from the config menu
The algorithm drivers are helper drivers that are selected automatically
as needed. There's no point in listing them in the config menu, it can
only confuse users and waste their time.
[SCSI] scsi_transport_sas: fix the lifetime of sas bsg objects
scsi_transport_sas calls blk_cleanup_queue too early for bsg
queues. If a user holds a sas_host, end_device, or expander device
open, remove the device, then send a request to it, we get a kernel
crash. We need to call blk_cleanup_queue in the release callback as we
do with scsi devices.
This patch moves blk_cleanup_queue to sas_expander_release and
sas_end_device_release from sas_bsg_remove. sas_host can't use the
release callback in struct device so use bsg's release callback.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds release callback support, which is called when a bsg
device goes away. bsg_register_queue() takes a pointer to a callback
function. This feature is useful for stuff like sas_host that can't
use the release callback in struct device.
If a caller doesn't need bsg's release callback, it can call
bsg_register_queue() with NULL pointer (e.g. scsi devices can use
release callback in struct device so they don't need bsg's callback).
With this patch, bsg uses kref for refcounts on bsg devices instead of
get/put_device in fops->open/release. bsg calls put_device and the
caller's release callback (if it was registered) in kref_put's
release.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sun, 23 Mar 2008 03:42:27 +0000 (22:42 -0500)]
[SCSI] rework scsi_target allocation
The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.
Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hannes Reinecke [Tue, 18 Mar 2008 13:32:28 +0000 (14:32 +0100)]
[SCSI] use default attributes for scsi_host
This patch removes the unused sysfs attibute overwriting logic for
the scsi host attibutes, and plugs them into the driver core default
attribute creation.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Fri, 21 Mar 2008 01:47:52 +0000 (20:47 -0500)]
[SCSI] sysfs: make group is_valid return a mode_t
We have a problem in scsi_transport_spi in that we need to customise
not only the visibility of the attributes, but also their mode. Fix
this by making the is_visible() callback return a mode, with 0
indicating is not visible.
Also add a sysfs_update_group() API to allow us to change either the
visibility or mode of the files at any time on the fly.
Acked-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hannes Reinecke [Tue, 18 Mar 2008 13:32:28 +0000 (14:32 +0100)]
[SCSI] qla2xxx, lfpc: Rename 'state' attribute to 'link_state'
lpfc and qla2xxx overwrite the standard 'state' attribute with
custom callbacks. So rename the custom attributes to 'link_state'
and retain the original meaning of the 'state' attribute.
Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Acked-by: James Smart <James.Smart@Emulex.Com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hannes Reinecke [Tue, 18 Mar 2008 13:32:28 +0000 (14:32 +0100)]
[SCSI] add scsi_host and scsi_target to scsi_bus
This patch implements scsi_host and scsi_target device types
and adds both to the scsi_bus.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 15 Mar 2008 18:01:40 +0000 (13:01 -0500)]
[SCSI] ses: fix up functionality after class_device->device conversion
ses uses an unusual two level class hierarchy which broke in this
conversion. Fix it up still with a two level hierarchy, but this time
let the ses device manage the links to and from the real device in the
enclosure.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Trent Piepho [Mon, 31 Mar 2008 04:19:29 +0000 (21:19 -0700)]
[MTD] [NOR] Read extended device ID from AMD/Spansion CFI flash chips
AMD/Spansion use a device id of 0x7e to indicate an extended device is
present at offset 0xe and 0xf in the query data.
I've verified with Spansion that all their chips (mfr == 0x01) with an id
of 0x7e use it to indicate an extended id is present. What's more, there
are no chips with a NON-extended id that is the same as a different chip's
extended id. In other words, when the extended ID is present, one can
replace the normal id with the extended id without losing any information.
Which is what I've done.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Anton Vorontsov [Fri, 28 Mar 2008 19:10:54 +0000 (22:10 +0300)]
[MTD] [NAND] fsl_elbc_nand: workaround for hangs during nand write
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Hamish Moffatt [Fri, 28 Mar 2008 04:00:00 +0000 (15:00 +1100)]
[MTD] [NAND] plat_nand: set mtd->name
This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.
Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: Hamish Moffatt <hamish@cloud.net.au> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Anton Vorontsov [Tue, 11 Mar 2008 19:33:13 +0000 (22:33 +0300)]
[MTD] [NAND] FSL UPM NAND driver
This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Lin Ming [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Fix to handle NULL package elements correctly
Fixed problem where NULL package elements were not returned to
the AcpiEvaluateObject interface correctly. Instead of returning a
NULL ACPI_OBJECT package element, the element was simply ignored,
potentially causing a buffer overflow and/or confusing the caller
who expected a fixed number of elements.
http://bugzilla.kernel.org/show_bug.cgi?id=10132
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Fix for extraneous debug message for packages
Fixed a problem where an extraneous debug message was produced for
package objects (when debugging enabled). The message "Package
List length larger than NumElements count" is now produced in
the correct case, and is also an error message rather than a
debug message. Added a debug message for the opposite case, where
NumElements is larger than the Package List, and the package has
been padded out with NULL elements.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
drivers/input/keyboard/lm8323.c: In function 'lm8323_pwm_store_time':
drivers/input/keyboard/lm8323.c:590: warning: passing argument 3 of 'strict_strtoul' from incompatible pointer type
drivers/input/keyboard/lm8323.c: In function 'lm8323_set_disable':
drivers/input/keyboard/lm8323.c:664: warning: passing argument 3 of 'strict_strtoul' from incompatible pointer type
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
[MTD] [MAPS] Extend plat-ram to support a supplied probe type
This enhances plat-ram to take a map_probes argument in
the platform_data structure which allow plat-ram to support
any direct-mapped device that MTD supports (jedec, cfi, amd ..)
A few items are also fixed:
- Don't panic if probes is 0
- Actually use the partition list that is passed in
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Paulius Zaleckas [Tue, 26 Feb 2008 23:42:39 +0000 (01:42 +0200)]
[MTD] XIP: Use generic xip_iprefetch() instead of asm volatile (...)
Untested, but shouldn't break anything... Makes MTD_XIP arch
independent. I guess this is why xip_iprefetch() was made for.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Fix for possible error when packages/buffers are passed to methods externally
Fixed a problem where buffer and package objects passed as
arguments to a control method via the external AcpiEvaluateObject
interface could cause an AE_AML_INTERNAL exception depending on the
order and type of operators executed by the target control method.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Update behavior of CopyObject to match ACPI spec
Fixed a problem where a CopyObject to RegionField, BankField, and
IndexField objects did not perform an implicit conversion as it
should. These types must retain their initial type permanently as
per the ACPI specification. However, a CopyObject to all other
object types should not perform an implicit conversion, as per
the ACPI specification.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Fix for resource descriptor optimization issues for _CRS/_SRC
Fixed a problem where resource descriptor size optimization
could cause a problem when a _CRS resource template is passed
to a _SRS method. The _SRS resource template must use the same
descriptors (with the same size) as returned from _CRS. This
change affects the following resource descriptors: IRQ/IRQNoFlags
and StartDependendentFn/StartDependentFnNoPri.
http://bugzilla.kernel.org/show_bug.cgi?id=9487
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:43 +0000 (19:06 +0400)]
ACPICA: Disassembler support for new ACPI tables
Implemented full disassembler support for the following new ACPI
tables: BERT, EINJ, and ERST. Partial disassembler support for
the complicated HEST table. These tables support the Windows
Hardware Error Architecture (WHEA).
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Fix for ACPI_HIDWORD macro
Fixed a regression introduced in version 20071114. The ACPI_HIDWORD
macro was inadvertently changed to return a 16-bit value instead of
a 32-bit value, truncating the upper Dword of a 64-bit value. This
macro is only used to display debug output, so no incorrect
calculations were made.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Added new error messages
New messages for the 2 AE_SUPPORT cases.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Add va_end statements as appropriate
Added missing va_end statements that should correspond with each
va_start statement.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Bulletproof disassembler for bad ACPI tables
Fixed a problem with the disassembler where invalid ACPI tables
could cause faults or infinite loops.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Include file support for new ACPI tables
Implemented header file support for new ACPI tables - BERT, ERST,
EINJ, HEST, IBFT, UEFI, WDAT. Disassembler support is forthcoming.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Fix for LoadTable operator, input strings
Fixed a problem with the LoadTable operator where the OemId
and OemTableId input strings could cause unexpected failures if
they were shorter than the maximum lengths allowed.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:42 +0000 (19:06 +0400)]
ACPICA: Methods now implicitly return 0 in slack mode
Implemented an enhancement to the interpreter "slack mode". In the
absence of an explicit return or an implicitly returned object from
the last executed opcode, a control method will now implicitly
return an integer of value 0 for Microsoft compatibility.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Fix for SizeOf when used with Buffers and Packages
Fixed a problem with the SizeOf operator when used with Package
and Buffer objects. These objects have deferred execution for some
arguments, and the execution is now completed before the SizeOf is
executed. This problem caused unexpected AE_PACKAGE_LIMIT errors
on some systems.
http://bugzilla.kernel.org/show_bug.cgi?id=9558
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Undo accidental checkin of not-fully-tested mutex changes
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Fixed a problem with Index Fields where the Index register was incorrectly limited to a maximum of 32 bits
Now any size may be used.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Fixed a problem with AcpiGetDevices where the search of a branch of the device tree could be terminated prematurely
In accordance with the ACPI specification, the search is terminated
if a device is both not present and not functional (instead of
just not present.) Yakui Zhao.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Fixed a problem with CopyObject used in conjunction with the Index operator
The reference was incorrectly dereferenced before the copy. The
reference is now correctly copied.
http://bugzilla.kernel.org/show_bug.cgi?id=5391
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:41 +0000 (19:06 +0400)]
ACPICA: Fixed a problem with Index references passed as method arguments
References passed as arguments to control methods were dereferenced
immediately (before control was passed to the called method). The
references are now correctly passed directly to the called
method.
http://bugzilla.kernel.org/show_bug.cgi?id=5389
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Fixed a problem with FromBCD and ToBCD with some compilers
On some compilers, the ShortDivide function worked incorrectly,
causing problems with the BCD functions with large input
values. (Truncation from 64-bit to 32-bit occurred.) Internal
http://www.acpica.org/bugzilla/show_bug.cgi?id=435
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Fixes a problem with control method references within packages
Completes the package changes started with version 20071019.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Cleanup of debug output
Improved output of object dump routine.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Cosmetic changes only, no functional changes
Lint changes, fix compiler warnings, etc.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Cosmetic changes only, no functional changes
Lint changes, fix compiler warnings, etc.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:40 +0000 (19:06 +0400)]
ACPICA: Added additional parameter validation for LoadTable
Implemented additional parameter validation for the LoadTable
operator. The length of the input strings SignatureString,
OemIdString, and OemTableId are now checked for maximum
lengths.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Fixed a memory leak when Device or Thermal objects referenced in packages
Problem introduced in fix for Package references.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Fix for Load/LoadTable to specify load location
Fixed a problem with the Load and LoadTable operators where
the table location within the namespace was ignored. Instead,
the table was always loaded into the root or current scope.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Add error checks to prevent faults
Added additional error checking to prevent run-time faults.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Fix for memory leak related to DdbHandle objects
Fixed a memory leak where DdbHandle objects were not deleted
automatically at control method exit.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Fix a fault when storing DdbHandle to Debug object
Fixed a problem with the Debug object where a store of a DdbHandle
reference object to the Debug object could cause a fault.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:39 +0000 (19:06 +0400)]
ACPICA: Fix for Alias operator to see target child objects
Fixed a problem with the Alias operator when the target of the
alias is a named ASL operator that opens a new scope -- Scope,
Device, PowerResource, Processor, and ThermalZone. In these cases,
any children of the original operator could not be accessed via
the alias, potentially causing unexpected AE_NOT_FOUND exceptions.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Fix for namespace lookup problem
Fixed a problem where objects of certain types (Device,
ThermalZone, Processor, PowerResource) can be not found if they
are declared and referenced from within the same control method
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: New interfaces for table event handlers
Designed and implemented new external interfaces to install and
remove handlers for ACPI table-related events. Current events that
are defined are LOAD and UNLOAD. These interfaces allow the host to
track ACPI tables as they are dynamically loaded and unloaded. See
AcpiInstallTableHandler and AcpiRemoveTableHandler.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Add minimal disassembly support for the SLIC table
SLIC - Software Licensing Description Table.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Support for iASL - multiple files and wildcards
Implemented support to allow multiple files to be
compiled/disassembled in a single invocation. This includes
command line wildcard support for both the Windows and Unix
versions of the compiler. This feature simplifies the disassembly
and compilation of multiple ACPI tables in a single directory.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Updated error message for dynamic method serialization
Added more information to make the message clearer.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Fix for update of the Global Lock Handle
Fixed a problem where the global lock handle was not properly
updated if a thread that acquired the global lock via
executing AML code then attempted to acquire the lock via the
AcpiAcquireGlobalLock interface.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Thu, 10 Apr 2008 15:06:38 +0000 (19:06 +0400)]
ACPICA: Fix for package reference counts
Prevents infinite loop of 'Large Reference Count' messages in
aslts-bdemo-b286 test.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
projects / linux-2.6-omap-h63xx.git / log